Abstract
The wire electric discharge machining (WEDM) process is a violent thermal process in which a certain volume of metal is eroded by thousands of electrical discharges in a fraction of 1 s. The process is widely used in tooling, especially in the cutlery and mold industry. However, the poor properties of surfaces such as high tensile residual stresses, high surface roughness, white layers, and microcracks are generated in the process. These properties vary with different levels of process parameters. In this paper, a new graphical evaluation of micron-scale surface topography on WEDM process is proposed by the fractal method. The objective is to quantify 3D micron-scale surface topography effect of process parameters such as pulse-on time, pulse-off time, cutting feed rate, wire tension, wire speed, and water pressure on working surface in dressing. Firstly, adaptive measuring was conducted on the basis of 3D micron-scale surface topography by the Ł18(21×35) Taguchi standard orthogonal experiments; secondly, the fractal dimension was conducted to identify 3D micron-scale surface topography; and finally, the effect of WEDM process parameters was investigated with reference to the fractal dimension (FD) of 3D micron-scale surface. The results have shown that the pulse-on time is the most dominant factor in affecting the surface texture. Moreover, the interaction effect between process parameters is analyzed. It has also been observed that the optimized combination of pulse-on time of 3 μs, pulse-off time of 20 μs, cutting feed rate of 4 mm/min, wire tension of 6 kgf, wire speed of 6 m/min, and water pressure of 5 kgf is suitable for 3D micron-scale surface, and the FD of 3D micron-scale surface is increased by 11 %.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Rajurkar KP, Pandit SM (1988) Recent progress in electrical discharge machine technology and research. In: Proceedings of Manufacturing International 1988 Atlanta, Georgia, April, Vol 1, pp 219–226
Yang YD, Guo JW, Cheng XF, Masanori K (2011) Molecular dynamics simulation of the material removal mechanism in micro-EDM. Precis Eng 35:51–57
Qu J, Shih AJ, Scattergood RO (2002) Development of the cylindrical wire electrical discharge machining process, part 2: surface integrity and roundness. ASME J Manuf Sci Eng 124:708–714
Liao YS, Woo JC (1997) The effects of machining settings on the behavior of pulse trains in the WEDM process. J Mater Process Technol 71:433–439
Gatto A, Iuliano L (1997) Cutting mechanisms and surface features of WED machined metal matrix composites. J Mater Process Technol 65:209–214
Aminollah M, Alireza FT, Emanian E, Karimi D (2008) A new approach to surface roughness and roundness improvement in wire electrical discharge turning based on statistical analyses. Int J Adv Manuf Technol 39:64–73
Ramakrishnan R, Karunamoorthy L (2004) Surface roughness model for CNC wire electro discharge machining. J Manuf Techol Today 3(5):8–11
Mohammadi A, Tehrani AF, Emanian E, Karimi D (2008) Statistical analysis of wire electrical discharge turning on material removal rate. J Mater Process Technol 205:283–289
Patowari PK, Saha P, Mishr PK (2011) Taguchi analysis of surface modification technique using W-Cu powder metallurgy sintered tools in EDM and characterization of the deposited layer. Int J Adv Manuf Technol 54:593–04
Huang Y, Ming WY, Guo JW, Zhang Z, Liu GD, Li MZ, Zhang GJ (2013) Optimization of cutting conditions of YG15 on rough and finish cutting in WEDM based on statistical analyses. Int J Adv Manuf Technol. doi:10.1007/s00170-013-5037-3
Assarzadeh S, Ghoreishi M (2008) Neural-network-based modeling and optimization of the electro-discharge machining process. Int J Adv Manuf Technol 39:488–500
Yang RT, Tzeng CJ, Yang YK, Hsieh MH (2012) Optimization of wire electrical discharge machining process parameters for cutting tungsten. Int J Adv Manuf Technol 60:135–147
Patowari PK, Saha P, Mishra PK (2010) Artificial neural network model in surface modification by EDM using tungsten copper powder metallurgy sintered electrodes. Int J Adv Manuf Technol 51:627–638
Shi HZ, Xie S, Wang X (2013) A warpage optimization method for injection molding using artificial neural network with parametric sampling evaluation strategy. Int J Adv Manuf Technol 65:343–353
Razfar MR, Zinati RF, Haghshenas M (2011) Optimum surface roughness prediction in face milling by using neural network and harmony search algorithm. Int J Adv Manuf Technol 52:487–495
Ramasawmyam H, Blunt L (2002) 3D surface topography assessment of the effect of different electrolytes during electrochemical polishing of EDM surfaces. Int J Mach Tools Manuf 42:567–574
Ramasawmya H, Blunt L (2004) Effect of EDM process parameters on 3D surface topography. J Mater Process Technol 148:155–164
Jiang ZD, Wang HR, Fei B (2001) Research into the application of fractal geometry in characterising machined surfaces. Int J Mach Tools Manuf 41:2179–2185
Chen MJ, Pang QL, Wang JH, Cheng K (2008) Analysis of 3D microtopography in machined KDP crystal surfaces based on fractal and wavelet methods. Int J Mach Tools Manuf 48:905–913
Pentland P (1984) Fractal-based description of natural scenes. IEEE Trans Pattern Anal Mach Intell 6 (6):661–674
Rimini NR, Maimon O, Romano R (2012) Visual analysis of quality-related manufacturing data using fractal geometry Noa Ruschin-Rimini. J Intell Manuf 23:481–495
Eiji U, Takanori K, Hideaki M, Noriaki S (2013) Tissue characterization of coronary plaque by kNN classifier with fractal-based features of IVUS RF-signal. J Intel Manuf. doi:10.1007/s10845-013-0793-3
Mandelbrot BB (1982) The fractal geometry of nature. Freeman, San Francisco
Falconer KJ (1990) Fractal geometry mathematical foundation and application. Wiley, New York
Russel D, Hanson J, Ott E (1980) Dimension of strange attractors. Phys Rev Lett 45(14):1175–1178
Mason RL, Gunt RF, Hess JL (2003) Statistical design and analysis of experiments. Wiley, New York
Hicks CR, Turner JK (1999) Fundamental concepts and the design of experiments. Oxford University Press, New York
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Luo, G., Ming, W., Zhang, Z. et al. Investigating the effect of WEDM process parameters on 3D micron-scale surface topography related to fractal dimension. Int J Adv Manuf Technol 75, 1773–1786 (2014). https://doi.org/10.1007/s00170-014-6271-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-014-6271-z