Abstract
The electrochemical micromachining appears to be a promising candidate as a future micromachining technique that utilizes high frequency pulses for micron- to nanoscale material dissolution. This article presents a step towards the in-process monitoring based on waveforms generated during electrochemical micromachining. An attempt has been taken to correlate between the waveforms generated during machining and experimental outcomes such as material removal rate, machining time, and the dimensions of the microholes fabricated on commercially available nickel plate with prefabricated tungsten microtools. An electrical function generator is used as a signal source and a digital storage oscilloscope is provided for observing the nature of electrical pulses used and recording the waveforms generated during machining. The waveforms are subgrouped depending on the parameters used and analyzed to correlate the waveform shape and the machining outcomes. The digital storage oscilloscope also facilitates for observing the short-circuit condition which may occur during microdrilling. These results show that the shape of the waveforms and their corresponding values are in good agreement with the material removal rate, machining time, and on the dimension of fabricated microholes. Therefore, the proposed monitoring technique can be employed as a predictive tool in electrochemical micromachining.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Weng FT (2005) A study of supersonic-aided electrolysis. Int J Adv Manuf Technol 25:480–483
Lee ES, Shin TH, Kim BK, Baek SY (2010) Investigation of short pulse electrochemical machining for groove process on Ni-Ti shape memory alloy. Int J Prec Eng Manuf 11(1):113–118
Fan ZW, Hourng LW (2009) The analysis and investigation on the microelectrode fabrication by electrochemical machining. Int J Mach Tools Manuf 49:659–666
Bhattacharyya B, Mitra S, Boro AK (2002) Electrochemical machining: new possibilities for micromachining. Robot CIM Int Manuf 18:283–289
Bhattacharyya B, Malapati M, Munda J, Sarkar A (2007) Influence of tool vibration on machining performance in electrochemical micro-machining of copper. Int J Mach Tools Manuf 47(2):335–342
Ahn SH, Ryu SH, Choi DK, Chu CN (2004) Electro-chemical micro drilling using ultra short pulses. Precis Eng 28:129–134
Lee ES, Baek SY, Cho CR (2007) A study of the characteristics for electrochemical micromachining with ultrashort voltage pulses. Int J Adv Manuf Technol 31:762–769
Schuster R, Kirchner V, Allongue P, Ertl G (2000) Electrochemical micromachining. Science 289(5476):98–101
Kock M, Kirchner V, Schuster R (2003) Electrochemical micromachining with ultrashort voltage pulses—a versatile method with lithographical precision. Electrochim Acta 48:3213–3219
Ryu SH (2009) Micro fabrication by electrochemical process in citric acid electrolyte. J Mater Process Technol 209:2831–2837
Park JW, Lee DW (2009) Pulse electrochemical polishing for microrecesses based on a coulostatic analysis. Int J Adv Manuf Technol 40:742–748
Wang J (2006) Analytical electrochemistry, 3rd edn. Wiley, New Jersey
Bard AJ, Faulkner LR (2001) Electrochemical methods: fundamentals and applications, 2nd edn. Wiley, New York
Park BJ, Kim BH, Chu CN (2006) The effects of tool electrode size on characteristics of micro electrochemical machining. CIRP Ann Manuf Technol 55(1):197–200
Mithu MAM, Fantoni G, Ciampi J (2011) The effect of high frequency and duty cycle in electrochemical microdrilling. Int J Adv Manuf Technol. doi:10.1007/s00170-010-3123-3
Lu Y, Liu K, Zhao D (2010) Experimental investigation on monitoring interelectrode gap of ECM with six-axis force sensor. Int J Adv Manuf Technol. doi:10.1007/s00170-010-3105-5
Kurita T, Chikamori K, Kubota S, Hattori M (2006) A study of three-dimensional shape machining with an ECμM system. Int J Mach Tools Manuf 46:1311–1318
Choi SH, Ryu SH, Choi DK, Chu CN (2007) Fabrication of WC micro-shaft by using electrochemical etching. Int J Adv Manuf Technol 31:682–687
Zhu D, Rajurkar KP, Wei B (1997) Modeling and monitoring and control systems. J Manuf Sci Eng Trans ASME 119(4):770–775
Lu YH, Zhao DB, Zhu D (2004) Mechanical property analysis of inter-electrode gap in electrochemical machining based on six force components. Chin J Mech Eng 15(23):2142–2145
Rivera JL, Michalek DJ, Sutherland JW (2007) Air quality in manufacturing. In: Kutz M (ed) Environmentally conscious manufacturing. Wiley, New Jersey, pp 145–178
Lim YM, Lim HJ, Liu JR, Kim SH (2003) Fabrication of cylindrical micropins with various diameters using DC current density control. J Mater Process Technol 141:251–255
De Silva AKM, McGeough JA (1998) Process monitoring of electrochemical micromachining. J Mater Process Technol 76:165–169
Bhattacharyya B, Munda J, Malapati M (2004) Advancement in electrochemical micro-machining. Int J Mach Tools Manuf 44:1577–1589
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Mithu, M.A.H., Fantoni, G. & Ciampi, J. A step towards the in-process monitoring for electrochemical microdrilling. Int J Adv Manuf Technol 57, 969–982 (2011). https://doi.org/10.1007/s00170-011-3355-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-011-3355-x