Abstract
The effects of nonmetallic inclusions on weld metal microstructures were investigated. The inclusions were extracted from niobium microalloyed steel weld metal specimens, and examined with light and electron microscopic techniques. An EDS (Energy Dispensive Spectroscopy) system was used to determine the chemical composition of the inclusions. Correlation between weld metal and inclusion composition was established. Aluminum, titanium, sulfur, and iron were the most important elements in the inclusions that affect the final weld metal microstructure. Mn/Si ratio was also found to affect the amount of oxygen and acicular ferrite in the weld. The state of deoxidation, as indicated by the amount of FeO present in the inclusions, actually determines the recovery of alloying elements and the amount of oxygen in the weld pool. It also determines the chemical composition of the nonmetallic inclusions. Inclusions with high aluminum content tend to cluster together forming larger particles while pure silica or silicate particles are small and well disseminated in the weld metal. This explains the different inclusion size distributions observed in the weld specimens of different oxygen concentration. Consequently, the prior austenite grain size will be different resulting in different amounts of acicular ferrite and grain boundary ferrite.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
R. Kiessling, “Non-Metallic Inclusions in Steel. Parts I–IV,” London, The Metal Society, 1978.
L.G. Twidwell, “Physical Chemistry of Iron and Steel-making,” Butte, Montana College of Mineral Science and Technology.
U.S. Steel Corporation “The Making, Shaping, and Treating of Steels,” 9th Edition, Pittsburgh, U.S. Steel Corporation, p. 281, 1971.
E.T. Turkdogan, “Deoxidation of Steel,”Journal of The Iron and Steel Institute, 1972, v. 12, p. 21.
O. Grong, T.A. Siewert, G.P. Martins, and D.L. Olson, “A model for the sequence of reactions occurring during silicon-manganese deoxidation of mild and low alloy steel weld metals.” Submitted for publication.
N.E. Hannerz and T. Werlefors, “The Influence of Parent Material Aluminum Content on Microstructure, Inclusion Distribution, and Mechanical Properties of Submerged Arc Weld Metal” in Proc. Intl. Conf. on “Trends in Steels and Consumables for Welding,” London, The Welding Institute, p. 335, 1978.
K. Narita, “Observation, Identification and Determination of Nonmetallic Inclusions and Precipitates in Steel,”Trans. ISIJ, 1976, V. 16, p. 208.
I. Taguchi, “Inclusion Analysis of Steel Samples” in Proc. Symp. on “Analysisof Ferrous and Non-Ferrous Metals,” Peking, 1980.
F. Kurosawa, I. Taguchi, M. Tanino, H.G. Suzuki, and R. Matsumoto, “Observation and Analysis of Precipitates Formed in Steels at Elevated Temperatures using the Non-Aqueous Electrolytic-Potentiostatic Etching Method,”Journal of Japan Institute of Metals, 1981, V. 45, p. 72.
P.H. Salmon Cox, and J.A. Charles, “Further Observations on the Analysis and Distribution of Non-Metallic Inclusions in a 0.2% C Steel Ingot,”Journal of The Iron and Steel Institute, 1965, v. 5, p. 493.
S.E. Lunner, “Origin and Types of Slag Inclusions in Non-Stabilized Austenitic Acid Resistant Steel,”Journal of The Iron and Steel Institute, 1972, v. 12, p. 168.
A.S. Venkatadri, “Mechanisms of Formation of Non-Metallic Inclusions in Aluminum-Killed Steels,”Trans. ISIJ, 1978, V. 18, p. 591.
B. Ahlblom, H. Bergstrom, N.E. Hannerz, and I. Werlefors, “Influence of Welding Parameters on Nitrogen Content and Microstructure of Submerged Arc Weld Metal” in Proc. Intl. Conf. on “The Effects of Residual, Impurity and Micro-alloying Elements on Weldability and Weld Properties,” London, The Welding Institute, Paper 38, 1983.
R.C. Cochrane, J.L. Ward, and B.R. Keville, “The Influence of Deoxidation and/or Desulphurisation Practice on the Weld Metal Toughness of High Dilution Welds” in Proc. Intl. Conf. on “The Effects of Residual, Impurity and Micro-alloying Elements on Weldability and Weld Properties,” London, The Welding Institute, Paper 16, 1983.
S. Liu, C.B. Dallam, and D.L. Olson, “Performance of the CaF2-CaO-SiO2 system as a submerged arc welding flux for a niobium based HSLA steel” in Proc. of ASM Intl. Conf. on “Welding Technology for Energy Applications,” Gatlinburg, Tenn., p. 445, 1982.
J.H. Doyle, “ZAG 80: An improved Quantitative Analysis for the Flextran Language Systems,” Rockwell Int. Report, RFP-3215, Rocky Flats Plant, Golden, Co., 1981.
D.J. Widgery, “New ideas on Submerged Arc Welding” in Proc. Intl. Conf. on “Trends in Steels and Consumables for Welding,” London, The Welding Institute, p. 217, 1978.
B.A. Graville, “Factors affecting the Toughness of Submerged Arc Weld Metal—Part II,”Technology Focus (Welding Institute of Canada), V. 2, p. 1, 1980.
C.B. Dallam, S. Liu, and D.L. Olson, “Flux composition dependence of microstructure and toughness of submerged arc HSLA weldments,”Welding Journal, 1985, 64(5): pp. 140-s–151-s.
P.L. Harrison, and R. A. Farrar, “Influence of oxygenrich inclusions on the austenite to ferrite phase transformation in high-strength low-alloy (HSLA) steel weld metals,”Journal of Materials Science, 1981, vol. 16: p. 2218.
M. Ferrante, and R. A. Farrar, “The role of oxygen rich inclusions in determining the microstructure of weld metal deposits,”Journal of Materials Science, 1982, vol. 17, p. 3293.
S. Liu and D.L. Olson, “The Role of Inclusions in Controlling HSLA Steel Weld Microstructures,”Welding Journal, 1986, vol. 65(6); pp. 139-s–150-s.
J.W. Jang, S. Shah, and J.E. Indacochea, “Influence of SAW Fluxes on Low Carbon Steel Weld Microstructure” in Conference ProceedingsASM Materials Week ’85, Toronto, Canada, 1985.
S. Kanazawa, A. Nakashima, K. Okamoto, and K. Kanaya, “Improvement of weld fusion zone toughness by fine TiN,”Transactions ISTJ 16, p. 486, 1976.
G.W. Heintze, and R. McPherson, “Grain refinement of steels by titanium innoculation during submerged arc welding,”Australian Welding Journal, 1983, vol. 28, p. 37.
N. Mori, H. Homma, S. Okita, and K. Asano, “The behavior of B and N in notch toughness improvement of Ti-B bearing weld metals,” IIW DOC IX-1158-80, 1980.
G.W. Heintze and R. McPherson, “Solidification Control of Submerged Arc Welds in Steels by Inoculation with Ti,”Welding Journal 1986, Vol. 65(3): pp. 71s-82s.
R.J. Pargeter,Investigation of Submerged Arc Weld Metal Inclusions. The Welding Institute, Cambridge, England, 1981.
B.R. Keville and R.C. Cochrane, “Factors controlling the microstructure and toughness of submerged arc weldments” in Proc. 30th Annual Convention onWelding Technology 82, Hobart, The Australian Welding Institute, p. 263, 1982.
R.C. Cochrane, J.L. Ward, and B.R. Keville, “The Influence of deoxidation and/or desulphurisation practice on the weld metal toughness of high dilution welds” in Proc. Intl. Conf. on “The Effects of Residual, Impurity and Micro-alloying Elements on Weldability and Weld Properties,” London, England, The Welding Institute, Paper 16, 1983.
H. Terashima and P.H.M. Hart, “Effect of Flux TiO2 and Wire Ti Content on Tolerance to High Al Content of Submerged Arc Welds made with Basic Fluxes” in Proc. Intl. Conf. on “The Effects of Residual, Impurity and Micro-alloying Elements on Weldability and Weld Properties,” London, The Welding Institute, p. 27, 1983.
M.E. Saggesse, A.R. Bhatti, D.N. Hawkins, and J.A. Whiteman, “Factors influencing inclusions chemistry and microstructure in submerged arc welds” in Proc. Intl. Conf. on “The Effects of Residual, Impurity and Microalloying Elements on Weldability and Weld Properties,” London, England, The Welding Institute, Paper 15, 1983.
R.A. Ricks, P.R. Howell, and G.S. Barritte, “The Nature of Acicular Ferrite in HSLA Steel Weld Metals,”Journal of Materials Science, 1982, Vol. 17, p. 732.
J.K. Brownlee, Matlock, and G.R. Edwards, “Effects of Aluminum and titanium on the Microstructure and Properties of Microalloyed Steel Weld Metal” in Conf. Proceedings on “Trends in Welding Research,” ASM/ AWS, Gatlinburg, Tenn., 1986.
L. Devillers, D. Kaplan, B. Marandet, A. Ribes, and P.V. Riboud, “The effect of low level concentrations of some elements on the toughness of submerged arc welded C-Mn welds” in Proc. Intl. Conf. on “The Effects of Residual, Impurity and Micro-alloying Elements on Weldability and Weld Properties,” London, England, The Welding Institute, p. 1, 1983.
G.S. Barritte, R.A. Ricks, and P.R. Howell, “Application of STEM/EDS to study of microstructural development in HSLA steel weld metals” in Proc. on “Quantitative Microanalysis with High Spatial Resolution, London, England, The Metals Society, p. 122, 1981.
E.S. Kayali, J.M. Corbett, and H.W. Kerr, “Observations on inclusions and acicular ferrite nucleation in submerged arc HSLA welds,”Journal of Materials Science Letters, 1983, vol. 2, p. 123.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Liu, S., Olson, D.L. The influence of inclusion chemical composition on weld metal microstructure. J. Mater. Eng. 9, 237–251 (1987). https://doi.org/10.1007/BF02834144
Issue Date:
DOI: https://doi.org/10.1007/BF02834144