Abstract
Scratch and mar durability of clear coatings are issues of concern to the automobile manufacturer and paint supplier. Scratching of clearcoats is a consequence of tribological events encountered by painted exteriors during normal service life. Several subjective methods to assess scratch durability have been proposed. These methods offer little insight into scratch mechanisms. More recently, single scratch methods have been proposed to probe clearcoat scratch mechanisms. This paper outlines a reliable and robust scratch methodology for evaluating scratch durability of automotive clear coatings. It is shown that, with appropriate characterization of tip geometry, quantitative and reproducible critical load values can be obtained. A suggested test method for scratch durability is described.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Ramamurthy, A.C., Buresh, G.A., Nagy, M., and Howell, M., “Novel Instrumentation for Evaluating Stone Impact Wear of Automotive Paint Systems,”Wear, 225, 936 (1999).
Rutherford, K.L., Trezona, R.I., Hutchings, I.M., and Ramamurthy, A.C., “The Abrasive and Erosive Wear of Polymeric Paint Films,”Wear, 203, 325 (1997).
Pickles, M.J., Trezona, R.I., Hutchings, I.M., Ramamurthy, A.C., and Freese, J.W., “New Methods for Characterizing the Mechanical Durability of Automobile Paint Films,” SAE International, Paper 980977, Detroit, MI, 1998.
Ramamurthy, A.C., Charest, J.A., Lilly, M.D., Mihora, D.J., and Freese, J.W., “Friction Induced Paint Damage—A Novel Method for Objective Assessment of Painted Engineering Plastics,”Wear, 203, 350 (1997).
Ramamurthy, A.C., Buresh, G., Jones, A., Shah, S., Szczepanaik, E., Edge, D., Freese, J.W., and. Linberg, P., “Durability of Painted Automotive Exteriors Subject to High-Pressure Water Jets-Simulation of Free Car Wash Environments,” SAE International, Paper 980974, Detroit, MI, 1998.
Ottviani, R.A., Iyengar, V., and Cheever, G.D., “Use of the Goniophotometer for Scratch and Mar Testing of Automotive Topcoats,” SAE International, Paper 970988, Detroit, MI, 1997.
Potter, R.A., Jacobs, P.B., Engbert, T., and Bock, M., “Scratching of Automotive OEM Clearcoats—Method and Media Effects,” SAE International, Paper 980975, Detroit, MI, 1998.
Jacobs, P.B. and Engbert, T., “Studies on Scratch and Mar Resistance of Polyurethane Coatings,” SAE International, Paper 960913, Detroit, MI, 1996.
Ramamurthy, A.C., Buresh, G.A., Buresh, J., Moorehead, P., Gale, L., and Belanger, L.,Proc. ACT 99 Conference, The Engineering Society of Detroit, Detroit, MI, September 1999.
Shen, W., Smith, S.M., Jones, F.N., and Ji, C., “Use of a Scanning Probe Microscope to Measure Marring Mechanisms and Microhardness of Crosslinked Coatings,”Journal of Coatings Technology,60, No. 873, 123 (1997).
Ryntz, R., Abell, B.D., and Hermosillo, F., “Scratch Resistance of Automotive Plastic Coatings,” SAE International, Detroit, MI, 1998.
Jones, F.N., Shen, W., Smith, S.M., Huang, Z., and Ryntz, R.A.,Prog. Org. Coat., 34, 119 (1998).
Adamson, K.G., Blackman, G., Gregorovich, B., Lin, L., and Matheson, R., “Oligomers in the Evolution of Automotive Clearcoats,”Prog. Org. Coat., 34, 64–74 (1998).
Blackman, G.S., Lin, L., and Matheson, R.R., “Micro-Mechanical Characterization of Mar Behavior of Automotive Topcoats: Micro and Nano-Wear of Polymeric Materials,”Proc. Polym. Prep. (Am. Chem. Soc., Div. Polym. Chem.), 39, No. 2, 1224 (1998).
Blackman, G.S., Lin, L., and Matheson, R.A., “Micro and Nano Wear of Polymeric Materials,”Proc. Polym. Prep. (Am. Chem. Soc., Div. Polym. Chem.), p. 1218, Boston, 1998.
Oliver, W. and Pharr, G.M., “An Improvement for Determining Hardness and Elastic Modulus Using Load and Displacement Sensing Indentation Experiments,”J. Mater. Res., Vol. 7, No. 6, June 1992.
Lucas, B., Oliver, W., Pharr, G.M., and Loubet, J.L., “Time Dependent Deformation During Indentation Testing,”Proc. Mat. Res. Soc. Symp., 436, 1997.
Lucas, B., Oliver, W.C., and Ramamurthy, A.C., “Spatially Resolved Mechanical Properties of a “TPO” Using a Frequency Specific Depth-Sensing Indentation Technique,”Proc. Antec 97, Volume III, Society of Plastic Engineers, 1997.
Jardret, V., Zahouani, H., Loubet, J.L., and Mathia, T.G., “Understanding and Quantification of Elastic and Plastic Deformation during a Scratch Test,”Wear, 218, 8–14 (1998).
Briscoe, B., Evans, P.D., Pelillo, E., and Sinha, S.K., “Scratching Maps for Polymers,”Wear, Vol. 200, 1996.
Lucas, B., Oliver, W.C., Pharr, G.M., and Loubet, J.L., “Time Dependent Deformation During Indentation Testing,”Proc. Mat. Res. Soc. Symp., Vol. 436, 1997.
Jardret, V. and Oliver, W.C., “Thin Films: Stresses and Mechanical Properties,”Proc. Mater. Res. Soc. Symp., 594, Boston, MA, 1999.
Author information
Authors and Affiliations
Additional information
Oak Ridge, TN.
401 Southfield Rd., A103L, Dearborn, MI 48121-6231.
Rights and permissions
About this article
Cite this article
Jardret, V., Lucas, B.N., Oliver, W. et al. Scratch durability of automotive clear coatings: A quantitative, reliable and robust methodology. Journal of Coatings Technology 72, 79–88 (2000). https://doi.org/10.1007/BF02698026
Issue Date:
DOI: https://doi.org/10.1007/BF02698026