Abstract
The fraction of plastic work converted to heat is typically measured either by nearly isothermal experiments, in which the thermal energy is measured during a deformation experiment with a calorimeter, or by adiabatic experiments, in which the thermal energy is determined from the temperature rise, measured either during the test or immediately after the test by dropping the sample into a calorimeter. In the present work, the temperature is measured with a single fine-wire thermocouple. The restriction to adiabatic loadings is relaxed by using a hybrid method that combines the measurements with finite difference simulations to calculate the heat losses that occur during the test. These heat losses are then accounted for in the final energy balance to determine the fraction of plastic work converted to heat. The method is applied to annealed 302 stainless steel. The results show that the fraction of plastic work converted to heat is a decreasing function ranging from 0.7 to 0.4 over a tensile strain range of 0 to 0.15. An analysis of the restrictions to this method and of the potential errors is given.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Bell, J., The Experimental Foundations of Solid Mechanics, Springer-Verlag, New York (1973).
Farren, W.S. andTaylor, G.I., “The Heat Developed During Plastic Extension of Metals,”Proc. Roy. Soc. Series A,107,422–451 (1925).
Taylor, G.I. andQuinney, M.A., “The Latent Heat Remaining in a Metal After Cold Work,”Proc. Roy. Soc., Series A,143,307–326 (1934).
Bever, M.B., Holt, D.L., and Titchener, A.L., “The Stored Energy of Cold Work,” Prog. Mat. Sci.,17 (1973).
Nabarro, F.R.N., Theory of Crystal Dislocations, Dover, New York, (1987).
Zehnder, A.T., “A Model for the Heating Due to Plastic Work,”Mechanics Research Communications,18,23–28 (1991).
Aravas, N., Kim, K.S., andLeckie, F.A., “On the Calculations of the Stored Energy of Cold Work,”J. Eng. Mat. Tech.,112,465–475 (1990).
Mason, J.J., Rosakis, A.J., andRavichandran, G., “On the Strain and Strain-rate Dependence of the Fraction of Plastic Work Converted to Heat: An Experimental Study Using High Speed Infrared Detectors and the Kolsky Bar,”Mech. Mat.,17,135–145 (1994).
Beghi, M.G., Bottani, C.E., Caglioti, G., andLenti, A., “Energy Balance via Thermal Emission in Copper Under Stress,”Mat. Lett.,6,133–137 (1988).
Wong, A.K. and Kirby, G.C. III, “Determination of the Heat Dissipated from a Specimen Undergoing Cyclic Plasticity by a Hybrid Numerical/Experimental Method,” NRL Memorandum Report 6633 (1990).
Omega Corporation, The Temperature Handbook (1997).
Carlson, D.E., “Linear Thermoelasticity,”Encyclopedia of Physics,VIa/2,Mechanics of Solids II,ed. C. Truesdell,Springer-Verlag,New York,297–345 (1972).
Holman, J.P., Heat Transfer, 8th ed., McGraw-Hill, New York (1997).
Murio, D.A., The Mollification Method and the Numerical Solution of Ill-posed Problems, John Wiley & Sons, New York (1993).
Groetsch, C.W., “Optimal Order of Accuracy in Vasin's Method for Differentiation of Noisy Functions,”J. Optimization Theory and Applications,74,373–378 (1992).
Murio, D.A., “Automatic Numerical Differentiation by Discrete Mollification,”J. Computational Mathematics with Applications,13,381–386 (1987).
Thomas, J.W., Numerical Partial Differential Equations, Springer-Verlag, New York (1995).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Zehnder, A.T., Babinsky, E. & Palmer, T. Hybrid method for determining the fraction of plastic work converted to heat. Experimental Mechanics 38, 295–302 (1998). https://doi.org/10.1007/BF02410392
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1007/BF02410392