Zusammenfassung
Es wird ein Prinzip der stationären gegenseitigen potentiellen Energie aufgestellt für zwei Belastungssysteme eines elastischen Balkens veränderlicher Biegesteifigkeit. Aus diesem Prinzip wird eine hinreichende Bedingung für stationäres Gewicht eines Sandwichbalkens abgeleitet, wenn die von einer Belastung an einem bestimmten Querschnitt erzeugte Durchbiegung vorgeschrieben ist. Für statisch bestimmte Balken wird gezeigt, dass diese Bedingung ein globales Minimum des Gewichts sicherstellt. Anwendungsbeipiele und Erweiterungen werden besprochen.
Article PDF
Avoid common mistakes on your manuscript.
References
J. L. Lagrange,Sur la figure des colonnes, Miscellanea Taurinensia, Vol. 5, 1773=Oeuvres de Lagrange, Vol. 2 (Gauthier-Villars, Paris 1868), pp. 125–170.
W. Prager andJ. E. Taylor,Problems of Optimal Structural Design, J. appl. Mech.35, 102 (1968).
W. Prager andR. T. Shield,Optimal Design of Multi-purpose Structures, Internat. J. Solids Structures4, 469 (1968).
C. Y. Sheu andW. Prager,Minimum-weight Design with Piecewise Constant Specific Stiffness, J. Optimiz. Theory Applicat.2, 179 (1968).
W. Prager,Optimality Criteria in Structural Design, Proc. Nat. Ac. Sci.61, 794 (1968).
G. A. Hegemier andW. Prager,On Michell Trusses, Internat. J. Mech. Sci.11, 209 (1969).
W. Prager,Optimality Criteria Derived from Classical Extremum Principles, in:An Introduction to Structural Optimization, University of Waterloo (Waterloo, Ontario, Canada, 1969). p. 165–178.
L. J. Icerman,Optimal Structural Design for Given Dynamic Deflection, Internat. J. Solids Struct.5, 473 (1969).
W. Prager,Optimal Structural Design for Given Stiffness in Stationary Creep, Z. angew. Math. Phys.19, 252 (1968).
J. E. Taylor,The Strongest Column — An Energy approach, J. appl. Mech.34, 486 (1967).
J. E. Taylor andC. Y. Liu,Optimal Design of Columns, AIAA J.6, 1497 (1968).
J. E. Taylor,Minimum-mass Bar for Axial Vibration at Specified Natural Frequency, AIAA J.5, 1911 (1967).
J. E. Taylor,Optimum Design of a Vibrating Bar with Specified Minimum Cross Section, AIAA J.6, 1379 (1968).
C. Y. Sheu,Elastic Minimum Weight Design for Specified Fundamental Frequency Internat. J. Solids Struct.4, 953 (1968).
C. Y. Sheu andW. Prager,Optimal Plastic Design of Circular and Annular Sandwich Plates with Piecewise Constant Cross Section, J. Mech. Phys. Solids17, 11 (1969).
D. C. Drucker andR. T. Sheield,Design for Minimum Weight, Proc. 9th Internat. Congr. appl. Mech., Brussels 1956, Vol. 5,212–222.
R. L. Barnett,Minimum-weight Design of Beams for Deflection, Proc. ASCE87, EM1, 75 (1961).
E. J. Haug, jr. andP. G. Kirmser,Minimum Weight Design with Inequality Constraints on Stress and Deflection, J. appl. Mech.34, 999 (1967);N. C. Huang andH. T. Tang,Minimum weight Design of Elastic Sandwich Beams with Deflection Constraints, J. Optimiz. Theory Applicat.4, 277 (1969).
E. J. Haug, Jr., T. D. Streeter andR. S. Newell,Optimal Design of Elastic Structural Elements, Report SY-RI-69, Systems Analysis Directorate, U.S. Army Weapons Command, Rock Island, Ill., 1969.
Author information
Authors and Affiliations
Additional information
This research was supported in part (W. P.) by the U.S. Army Research Office, Durham.
Rights and permissions
About this article
Cite this article
Shield, R.T., Prager, W. Optimal structural design for given deflection. Journal of Applied Mathematics and Physics (ZAMP) 21, 513–523 (1970). https://doi.org/10.1007/BF01587681
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF01587681