Summary
The paper gives a rigorous theory of rotating elasto-plastic shrink fits under the assumptions of infinitesimal strain, ideal plasticity and validity of Tresca's yield condition. The plastic strain increments are computed by the associated flow rule. Furthermore, it is assumed that the shaft remains purely elastic during the entire loading history. It is shown that, below a limit speed, the plastic deformation is governed by one side of the Tresca hexagon only. Beyond this speed, a second face of Tresca's hexagon becomes involved. In this case plastic prestrains accumulated below the limit speed have to be considered. For both speed regimes, solutions comprising stresses and radial displacement are obtained. Finally a numerical example is given.
übersicht
Der Aufsatz gibt eine exakte Theorie des rotierenden elasto-plastischen Preßverbandes unter den Voraussetzungen infinitesimaler Verzerrungen, idealer Plastizität und der Gültigkeit der Trescaschen Fließbedingung. Die plastischen Dehnungsinkremente werden nach der zugeordneten Fließregel berechnet. Ferner wird vorausgesetzt, daß die Welle während der vollständigen Belastungsgeschichte rein elastisch bleibt. Es wird gezeigt, daß unterhalb einer Grenzdrehzahl die plastische Deformation von nur einer Seite des Trescaschen Sechsecks bestimmt wird. Oberhalb dieser Drehzahl wird eine zweite Seite des Trescaschen Sechsecks beteiligt. In diesem Fall müssen plastische Vordehnungen berücksichtigt werden, die unterhalb der Grenzdrehzahl entstanden. Für beide Drehzahlbereiche werden Lösungen abgeleitet, welche Spannungen und Radialverschiebung umfassen. Schließlich wird ein numerisches Beispiel angegeben.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Kollmann, F. G.: Welle-Nabe-Verbindungen. Berlin, Heidelberg, New York, Tokyo: Springer 1984
Biezeno, C. B.; Grammel, R.: Technische Dynamik, 2nd ed., Vol. 2. Berlin, Heidelberg, New York: Springer 1971
Lundberg, G.: Die Festigkeit von Preßsitzen. Das Kugellager 19 (1944) 1–11
Kollmann, F. G.: Die Auslegung elastisch-plastisch beanspruchter Querpreßverbände. Forsch. Ing.-Wes. 44 (1978) 1–11
Koiter, T. W.: General theorems for elastic-plastic solids. In: Progress in solid mechanics Vol. 1, Amsterdam: North Holland 1960
Gamer, U.; Lance, R.: Elastisch-plastische Spannungen im Schrumpfsitz. Forsch. Ing.-Wes. 48 (1982) 192–198
Kollmann, F. G.: Rotating elasto-plastic interference fits. Trans. ASME, J. Mech. Des. 103 (1981) 61–66
Gamer, U.; Mack, W.: Thermal stress in an elastic-plastic disk exposed to a circular heat source. ZAMP 36 (1985) 568–580
Ismar, H.; Mahrenholz, O.: Technische Plastomechanik. Braunschweig: Vieweg 1979
Rand, R. H.: Computer algebra in applied mathematics: An introduction to MACSYMA. Boston, London, Melbourne: Pitman 1984
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Gamer, U., Kollmann, F.G. A theory of rotating elasto-plastic shrink fits. Ing. arch 56, 254–264 (1986). https://doi.org/10.1007/BF00542477
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF00542477