Abstract
Problems in wind engineering are addressed using computational techniques, or computational wind engineering (CWE). Although Computational Fluid Dynamics (CFD) is just one component of CWE, it has up to now been used as a main tool. The vortex formation in wind turbines has to be studied certainly in order to avoid the formation of induced drag and methods that are required to minimize the effects of vorticity. The boundary layer formation analysis and vortex formation analysis in the blades of industrial wind turbines are solved using numerical techniques. To achieve the necessary flow characteristics, such as vortex generation and boundary layer creation in the wind turbine blades during flow separation, the lift-to-drag ratio, pressure coefficient, variation of lift with respect to the angle of attack, variation of drag with respect to the angle of attack, and intensity of induced drag brought on by vortex formation are studied using CFD. It also encloses the control and minimizing techniques of vorticity generation and boundary layer formation.
Access provided by Autonomous University of Puebla. Download conference paper PDF
Similar content being viewed by others
Keywords
1 Introduction
Humanity has known for ages how useful wind power can be in daily life, from sailboats to windmills. Developing and designing vertical axis wind turbines have been the subject of several research projects. Among the few investigations, two were emphasized here and categorized as computational studies and experimental studies. Due to population increase and the expansion of economies, the world's energy demand is anticipated to more than quadruple by 2060. Lift-based Darrieus VAWT design is more frequently utilized since it has larger power coefficients [1]. Darrieus VAWTs typically fall into one of two categories based on blade configuration: both straight and curved blades. Straight line blades, in particularly the H-rotor types, have gained popularity because of how easily they can be produced. On employing VAWT, maximum power coefficient can be achieved, but on the other hand, construction, operation, and cost of manufacturing are crucial considerations when choosing VAWTs as in [2] for power production. Power generation expenses will be decreased by raising the power coefficient of VAWTs and HAWTs.
2 Problem Statement
The present analysis incorporates the formation of vorticity in the wind turbines and the intensity of vortices in the tip and the root of the blades. Unlike the aircrafts, the vortex in the wind turbine blade is of different structures and it is an important aspect of study the vortex structure in the blades. The airfoils chosen are S833, S834, and S835 of the NREL series. Also, vorticity formation due to the upstream flow or the wind speed is analyzed and an insight on ways to reduce the vortices is given. The turbulence analysis is included in the paper and the corresponding results are provided.
3 Methodology
The paper is expected to exhibit the study of vortex formation in the wind turbines. Initially, the blade is designed with S833, S834, and S835 airfoils separately and the simulation is done with four different wind speeds, and the vortices’ formations are obtained. The turbulence models are taken and analyzed [3]. These airfoils are made with the intention of having a constrained maximum lift and a minimal sensitivity to leading-edge roughness [4]. In the past, an analysis for this type of wind turbine was performed where the analysis was performed for HAWT with a NACA airfoil. However, in this study, the HAWT blade type is chosen and S833, S834, and S835 airfoils are picked, and they are then given an aerodynamic analysis [5]. The vortex formations in the wind turbine is a function of wind speed which is why the analysis involves choosing different wind speeds in order to provide the best airfoil for wind turbines.
4 Code QBlade
The turbulence analysis and vorticity formation were simulated in QBlade. It is a wind turbine design and simulation software. QBlade is a software that helps to design wind turbine and maximizes all the key relations between blade twist, chord, section airfoil performance, turbine control, power, and load curves in a clear and understandable manner.
5 Theory
For quantitatively predicting liquid and gas flows in many industrial applications, Computational Fluid Dynamics (CFD) is a potent tool. Air flows around wind turbines to produce renewable energy by turning the turbine blades, which is an obvious application of CFD in wind energy.
5.1 Vorticity
The vortex flow is that type of flow in which the fluid particles take a rotational motion during its flow separation from the fluid–solid interaction. Free vortex flow and forced vortex flow are the two types of vortex flows, whereas in forced vortex flow, the fluid particles rotate in its own axis by means of the external torque applied to the fluid flow. Tangential velocity acting on the fluid,
The analysis is based on the formation of vortices in the wind turbine which replicates the number of vortex filaments that has formed during the flow separation in the wind turbine blades. The vortices are developed is formed in the downstream of the blades which induces a velocity at some points by Biot–Savart law.
By integrating the above expression, the velocity relation is obtained
The Lifting Line Free Vortex Wake technique may be used in QBlade to mimic the aerodynamic forces operating on a rotor (LLFVW). The FVW approach used in this study solves for the turbine wake. The FVW model is derived from Lagrangian method (Fig. 1).
6 Results and Discussions
In this analysis, geometric models of the airfoils have been created and vortex formations in the wind turbines are simulated for three different turbine blade geometries. According to the author’s knowledge, it is found theoretically that the number of vortex filaments formed across the wake of the blade is inversely proportional to the wind speed.
6.1 Geometric Model
The below given figure shows the blade design of the airfoils S833, S834, and S835:
-
1.
S833 (Fig. 2).
-
2.
S834 (Fig. 3).
-
3.
S835 (Fig. 4).
6.2 Vortex Simulations
The vortex simulations for four different wind speeds are shown:
-
(1)
Airfoil: S833 speed of wind in m/s
6.3 Turbulence Graphs
The graphs of blade length versus circulation, time versus induced velocity, and time versus vortex filaments for S833 are given below (Figs. 9, 10 and 11):
-
(2)
Airfoil: S834
6.4 Turbulence Graphs
The graphs of blade length versus circulation, time versus induced velocity and time versus vortex filaments for S834 are given below (Figs. 16, 17 and 18):
-
(3)
Airfoil: S835
6.5 Turbulence Graphs
The graphs of blade length versus circulation, time versus induced velocity, and time versus vortex filaments for S835 are given below (Figs. 23, 24 and 25):
7 Conclusion
The vorticity formation for the three airfoils has been obtained along with the graphs to study turbulence. The vortices formed during the working of a wind turbine affect the performance of it. Hence, it is essential to analyze and study ways to reduce them. From this analysis, it is found that distance between the wind turbine and the formation of vortex filaments is lesser at low wind speeds and formation of vortex filaments which is at high wind speeds is farther from the wind turbine. During the blade rotation, there is formation of vortices’ downstream of wind turbine. By comparing the airfoils S833, S834, S835 based on the formation of vortex filaments, it is found that for S834 airfoil, the distance between the formation vortex filaments and wind turbine is more at low wind speeds, whereas for S833 and S835 airfoils, the distance is less at low wind speeds.
Abbreviations
- v:
-
Tangential velocity (m/s)
- ґ:
-
Strength of vortex filament (m2/s)
- ω:
-
Angular velocity of fluid particle (rad/s)
- r:
-
Radial distance between elemental vortex filament and point in space
- l:
-
Total length of the vortex filament
References
Air KM (2012) Aerodynamic analysis of the NREL 5-MW wind turbine using vortex panel method master’s thesis in fluid mechanics
Chen W-H, et al (2021) Two-stage optimization of three and four straight-bladed vertical axis wind turbines (SB-VAWT) based on Taguchi approach. Electron Energy 1(December):100025. https://doi.org/10.1016/j.prime.2021.100025
Ngala G, Shuwa M (2015) A CFD analysis of a micro horizontal axis wind turbine blade a CFD analysis of a micro horizontal axis wind turbine blade aerodynamics. In: Center for entrepreneurial and enterprise development keywords : computerized fluid dynamics, wind turbine, aerodynamic, May 2020
Voutsinas SG (2006) Vortex methods in aeronautics: how to make things work. Int J Comput Fluid Dyn 20(1):3–18. https://doi.org/10.1080/10618560600566059
Xue Z, Fu J, Zhao M (2019) Numerical simulation and analysis of the arrangement of wind direction meter for wind turbine. In: E3S web conference, vol 118, pp 1–8. https://doi.org/10.1051/e3sconf/201911802040
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2024 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Ahamed, D., Maadesh, C., Adishwar, H., Mahadevan, A., Seeni, A. (2024). Computational Technique Adopted to Study Vortex Formation in Industrial Wind Turbines. In: Rajasekharan, S.G., Arunachalam, S., Harikrishna, P. (eds) Proceedings of the 9th National Conference on Wind Engineering. NCWE 2023. Lecture Notes in Mechanical Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-99-4183-4_11
Download citation
DOI: https://doi.org/10.1007/978-981-99-4183-4_11
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-99-4182-7
Online ISBN: 978-981-99-4183-4
eBook Packages: EngineeringEngineering (R0)