Abstract
In recent years, Fibre-Reinforced Polymer (FRP) bars have been used as reinforcement in concrete beams. However, the ductility of the beams is highly dependent on the properties of concrete since the failure mode of concrete is due to crushing. Substitution of concrete with Engineered Cementitious Composite (ECC) can avoid the ductility and durability problems associated with the concrete. In this paper, the flexural behaviour of FRP reinforced ECC-Concrete composite beams is numerically investigated through the Finite Element (FE) platform. To verify the robustness of the FE model of the composite beams, the simulation results were compared against the experimental results available in the literature and good agreements were achieved. An extensive parametric study was then conducted to examine the effect of the FRP reinforcement ratio against ECC layer thickness. It was observed that the load-carrying capacity of the composite beams is improved with the increase in ECC height replacement and Basalt Fibre Reinforced Polymer (BFRP) reinforcement ratios. In addition, composite beams show enhanced load-carrying capacity of 40% and 2%, of ECC layer thickness and FRP reinforcement ratio, respectively.
Access provided by Autonomous University of Puebla. Download chapter PDF
Similar content being viewed by others
Keywords
1 Introduction
Reinforced concrete (RC) structures exposed to corrosive environments, such as de-icing salts, chemical treatment plants, structures built in or close to seawater, etc., are suitable to be reinforced with Fiber-Reinforced Polymer (FRP) bars to eliminate durability problems [1]. Over the past two decades, FRP materials have been used as an alternative for steel reinforcement in concrete structures [2, 3]. However, FRP reinforcement has low elastic modulus and linear deformation properties, leading to large deflections and crack widths which leads to brittle failure, which has prevented FRP structures from being widely used [4].
Engineered Cementitious Composite (ECC) is a cement-based composite material exhibiting superior ductility (typically >3%, 300 times that of normal concrete or FRC), tight crack width (less than 80 µm), and relatively low fiber content (2% or less of short randomly oriented fibers) [5, 6]. ECC’s ultimate tensile strength and tensile strain capacities are 5–8 MPa and 3–5%, respectively. ECC’s compressive strength and compressive strain capacity range from 30 to 90 MPa and 0.45–0.65%, respectively [7]. ECC exhibits superior tensile strain hardening and multiple cracking behaviors by systematically tailoring the fiber, matrix, and interface properties, guided by micromechanics principles [8].
In order to enhance both the ductility and durability of structures, researchers proposed FRP reinforced ECC-Concrete composite beams. The excellent crack control ability and durability of ECC materials have encouraged the use of ECCs in the tensile zone around longitudinal steel reinforcement [9, 10]. The results showed that the flexural capacity and deformation ability slightly improve, but the crack width before yielding of steel reinforcement significantly decreases to just 20% of that in conventional RC beams [11, 12]. ECC-concrete composite beams reinforced with FRP bars were also to solve cracking and deflection problems associated with the brittleness of FRP-reinforced beams [13, 14].
2 Research Significance
Strength and ductility are critical parameters in the design of concrete structures. It is anticipated that utilizing FRP bars and ECC at strategic locations in the RC beam elements will give promising results in high strength and ductility. However, the successful utilization of ECC requires robust analysis and design procedures. Studies available in the literature deal only with modelling and analysis of FRP reinforced composite beam against particular ECC layer thickness and FRP reinforcement ratio. Hence, in this study, the numerical analysis of FRP reinforced ECC-Concrete composite beams with different reinforcement ratios against ECC layer thickness are investigated and presented the effects on the flexural capacity of the composite beams.
3 Finite Element Analysis
This research study is conducted on the nonlinear analysis, and the response of FRP reinforced ECC-Concrete composite beams under monotonic loading through FE analysis on the ABAQUS platform. The numerical investigation for the response of FRP reinforced ECC-Concrete composite beams under monotonic loading was performed in ABAQUS finite element software. For this purpose, three Basalt Fibre Reinforced Polymer (BFRP) reinforced ECC-Concrete composite beams chosen from the literature [13, 14] were modelled and analysed. The numerical results are obtained in terms of load–deflection response and compared with the experimental results.
Constitutive Model and Plasticity Parameters
In the present study, ECC and concrete are modelled using the damage plasticity model available in the ABAQUS nonlinear program to define the damage and failure mechanisms [15]. Uniaxial tensile and compression stress–strain responses (Fig. 1) are employed to develop the constitutive behaviour of the materials. The input parameters needed to model the constitutive behaviour of composite beams is presented in Table 1.
This model incorporates two main failure mechanisms in the form of tensile cracking and compressive crushing. Thus, damage parameters, strain hardening, and strain-softening rules for ECC and concrete materials are duly incorporated in this study. The compressive and tensile damage parameters (dc and dt) are calculated based on Eqs. (1), (2), respectively,
where \({\sigma }_{c}\) and \({\sigma }_{t}\) are compressive and tensile stresses, respectively, \({E}_{c}\) is the modulus of elasticity, \({\varepsilon }_{c}^{pl}\) and \({\varepsilon }_{t}^{pl}\) are plastic strains corresponding to compressive and tensile strengths, respectively. \({b}_{c}=\frac{{\varepsilon }_{c}^{pl}}{{\varepsilon }_{c}^{in}}\), \({\varepsilon }_{c}^{in}\)—compressive inelastic strain, \({b}_{t}=\frac{{\varepsilon }_{t}^{pl}}{{\varepsilon }_{t}^{cr}}\), \({\varepsilon }_{t}^{cr}\)—tensile cracking strain. \({b}_{c}\) and \({b}_{t}\) are the constant parameters that can vary from 0 to 1, whereas 1 means no damage and 0 means total damage.
The plasticity parameters following the Drucker-Prager criteria are employed to define the failure of ECC and concrete materials, which are present in [16] (Table 2).
Details of the Experimental Study
The details of the composite beam specimens available in the literature, which are used in this study, are presented in Table 3. During the experimental study, all the beam specimens were tested under vertical monotonic loading and the mid-point load–deflection response was measured. The loading patterns of the beam specimens are shown in Fig. 2.
Modelling of Composite Beams
The modeling procedure for the selected composite beams in the ABAQUS platform is discussed in this section. ECC and concrete are modeled using 8-noded linear hexahedral solid elements with reduced integration (C3D8R). A 2-noded nonlinear truss element (T3D2) is used for steel reinforcement. The embedded method with the perfect bond between reinforcement and the surrounding material is adopted to simulate the reinforcement-material bonding interaction properly. In addition to this, for composite beams, a perfect bond was assumed between concrete and ECC since experimentally, no debonding was observed between the materials. Hence, tie constraint (surface-to-surface property) generates the composite action. The boundary (simply supported ends) and loading conditions (two-point loading) were specified in the analysis. The geometry, reinforcement, boundary conditions and loading pattern of the composite beam simulated are shown in Fig. 3. The meshing of the beam element is performed by employing fine mesh (i.e., 30 × 30 mm mesh size) to attain an accurate response with the experimental results. An incremental displacement-control program was adopted to analyze the selected FRP reinforced composite beams.
4 Verification of Numerical Models
In this section, the load–deflection response of all the composite beams has been evaluated numerically and compared against the experimental results. The verification and discussion of the obtained results were discussed as follows.
Load–Deflection Response
To understand the effectiveness of the procedure adopted for the numerical simulation, the load–deflection response of the composite beams obtained from the FE analysis were compared against the results from the experimental study (Fig. 4).
In general, from Fig. 4 it can be seen that the numerical response shows good agreement with the experimental response. From Table 4, it can be observed that the difference between the numerical and experimental responses of the composite beams is less than 5% for all composite beams. This shows the robustness of the numerical procedure adopted for the analysis of the FRP reinforced composite beams.
5 Parametric Study
As is stated above, the numerical load–deflection behaviour agrees well with the experimental behaviour which shows the robustness of the employed numerical procedure. Hence, it is appropriate to adopt the same procedure for the parametric study. The parametric study includes:
-
Effect of ECC layer thickness against various FRP reinforcement ratio
-
Effect of FRP reinforcement ratio against various ECC layer thickness.
The parametric study is done to understand the effect of ECC layer thickness and BFRP reinforcement in the composite beam. For this purpose, a constant cross-section of the beam is used whereas the ECC layer thickness and BFRP reinforcement ratio are varied. The cross-section of the composite beam along with ECC layer thickness and BFRP reinforcement ratio is shown in Fig. 5.
Effect of ECC layer thickness against various FRP reinforcement ratio
In this section, the selected FRP reinforcement ratios are analysed for five different ECC layer thicknesses (i.e., 0, 20, 40 and 60% of the beam depth) to investigate the effect of various ECC layer thickness against each reinforcement ratio in composite beams.
The effect of the load-carrying capacity of the ECC-Concrete composite beams with different ECC layer thicknesses is shown in Fig. 6. It is observed that an increase in ECC layer thickness increases the load-carrying capacity of the beam, after a peak load is achieved, the load-carrying capacity decreases as an increase in ECC layer thickness. This behavior is observed in all composite beams employed in this study, irrespective of the reinforcement ratio. For a composite beam of a particular cross-section, 40% ECC layer thickness exhibits enhanced load carrying capacity for all reinforcement ratios used. However, with a further increase of the ECC layer thickness, the ultimate load carrying capacity of the composite beams were reduced to some extent. This was mainly because as the height of the ECC in the cross-section increased, and extent above the neutral axis where ECC materials are participated in the compressive zone. The incorporation of PVA fibres increases the porosity of the cement-based materials, which leads to internal structural damage, which in turn affects the compressive capacity of the beams. As the load increased, the overall load bearing capacity decreased. Therefore, there was an optimal range for cross-section replacement ratios. Hence, for this study the 40% ECC height replacement of the composite beams could obtain better mechanical properties and economic benefits.
Effect of FRP reinforcement ratio against various ECC layer thickness
In this section, the selected ECC layer thickness is analyzed for various FRP reinforcement ratios (0.4, 1.05 and 2%) to investigate the effect of reinforcement ratio for each ECC layer thickness in composite beams.
The effect of the load-carrying capacity of the ECC-Concrete composite beams with different FRP reinforcement ratios is shown in Fig. 7. It is understood that an increase in FRP reinforcement ratio increases the load-carrying capacity of full concrete and for all ECC-Concrete composite beams irrespective of the ECC layer thickness. Further, it is observed that the highest reinforcement ratio of 2%, showed enhanced load carrying capacity for the composite beam with 40% ECC layer thickness.
6 Conclusion
This study is conducted on the numerical analysis of BFRP reinforced ECC-Concrete composite beams and the obtained results are verified against the experimental studies. Upon analysis, the load–deflection response was generated. Based on the numerical and experimental results, the following conclusions are drawn:
-
The material constitutive model and plasticity parameters in the damage plasticity model are effectively used to define the behavior of ECC, concrete and FRP in the analysis.
-
Close agreement between the numerical and experimental results is observed. In addition, the difference between the peak load of the numerical and experimental responses of all the reinforced beams is within the range of 5%, which shows the robustness of the procedure adopted for FE models.
-
Generally, the load-carrying capacity of the composite beams is improved with the increase of the ECC height replacement and BFRP reinforcement ratios.
-
Composite beams of a particular cross-section exhibit enhanced load carrying capacity of 40 and 2%, of ECC layer thickness and FRP reinforcement ratio, respectively.
References
AE Naaman 2003 FRP reinforcements in structural concrete: assessment, progress and prospects Fibre-Reinf Polym Reinf Concr Struct 2 July 3 24
Wang H, Belarbi (2005) A flexural behavior of fiber-reinforced-concrete beams reinforced with FRP rebars
M Pecce G Manredi E Cosenza 2000 Experimental response and code models of gfrp rc beams in bending J Compos Constr 4 November 182 190
M Theriaule B Benmokrane 1998 Effects of FRP reinforcement ratio and concrete strength on flexural behavior of concrete beams J Compos Constr 2 February 7 16
VC Li 2003 On engineered cementitious composites (ECC) a review of the material and its applications J Adv Concr Technol 1 3 215 230
T Kanda VC Li 1999 New micromechanics design theory for pseudostrain hardening cementitious composite J Eng Mech 125 4 373 381
PM Arulanandam SB Singh T Kanakubo MVR Sivasubramanian 2020 Behavior of engineered cementitious composite structural elements—a review Indian Concr J 94 6 5 28
SB Singh MVR Sivasubramanian 2013 Performance of ductile fibre-reinforced cementitious composite concrete frames under flexural loading Proc Inst Civ Eng Constr Mater 166 1 34 44
VC Li S Wang C Wu 2001 Tensile strain-hardening behavior or polyvinyl alcohol engineered cementitious composite (PVA-ECC) ACI Mater J 98 6 483 492
F Yuan J Pan Y Wu 2014 Numerical study on flexural behaviors of steel reinforced engineered cementitious composite (ECC) and ECC/concrete composite beams Sci China Technol Sci 57 3 637 645
J Zhang CKY Leung YN Cheung 2006 Flexural performance of layered ECC-concrete composite beam Compos Sci Technol 66 11–12 1501 1512
M Maalej ST Quek SFU Ahmed J Zhang VWJ Lin KS Leong 2012 Review of potential structural applications of hybrid fiber Engineered Cementitious Composites Constr Build Mater 36 216 227
F Yuan J Pan CKY Leung 2013 Flexural behaviors of ECC and concrete/ECC composite beams reinforced with basalt fiber-reinforced polymer J Compos Constr 17 5 591 602
W-J Ge 2018 Flexural behavior of ECC-concrete hybrid composite beams reinforced with FRP and steel bars J Compos Constr 23 1 04018069
Systèmes SD (2012) ABAQUS user’s manual. Version 6.12. Simulia Corp. Johnston
AEH Khalil E Etman A Atta M Essam 2016 Nonlinear behavior of RC beams strengthened with strain hardening cementitious composites subjected to monotonic and cyclic loads Alexandria Eng J 55 2 1483 1496
Acknowledgements
This paper is the part of the author’s Ph.D. study enrolled at the National Institute of Technology Puducherry, India which is being supervised by the corresponding author.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2023 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this chapter
Cite this chapter
Arulanandam, P.M., Sivasubramanian, M.V.R., Singh, S.B. (2023). Effect of Layer Thickness and FRP Reinforcement Ratio on the Load Carrying Capacity of ECC Composite Beams. In: Singh, S.B., Gopalarathnam, M., Kodur, V.K.R., Matsagar, V.A. (eds) Fiber Reinforced Polymeric Materials and Sustainable Structures. Composites Science and Technology . Springer, Singapore. https://doi.org/10.1007/978-981-19-8979-7_6
Download citation
DOI: https://doi.org/10.1007/978-981-19-8979-7_6
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-19-8978-0
Online ISBN: 978-981-19-8979-7
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)