Abstract
The main objective is to investigate the present proceedings on the blast loads on the civil structures as an act of terrorism, industrialization or mining actions. Explosives are detonating materials that explode with high pressure on ignition. The blast explosion inside or at a proximity distance of a structure damages the structure physically, incurring trauma/death to the inmates or people in the surrounding. During the present Anthropogenic epoch, the act of terrorism has surged targeting mainly the commercial units, high-rise buildings, 5-star hotels and crowded places. The bombing action is done through a small packet bomb to suicidal trucks or even aeroplanes. Customarily while designing the imposed loads on a structure, the structural engineers consider the dead, live, lateral and seismic loads but do not consider the blast load. In designing important and high rising structures, it has become pertinent to consider blast loads (dynamic loads) along with other loads. Since it was not warranted, there was no code provision for the blast load in the design of structures. The present research is an attempt to review all the old literature available and to find the research gap before proceeding with the calculation of blast loads in the design of a structure. The conclusions derived from the research gap shall be helpful to understand the behaviour of blast loads on structures and can be useful in designing the important structures.
Access provided by Autonomous University of Puebla. Download conference paper PDF
Similar content being viewed by others
Keywords
1 Introduction
Blast loads are dynamic in nature and they cause catastrophic damage to the structures. An explosion releases a lot of energy in the form of light, heat, sound and shock waves. These waves can propagate through the structure in a very short duration and lead to the collapse of the structure. So, there is a significant need to design the structure as a blast-resistant structure. Structural irregularities also play a prominent role in designing blast-resistant structures. Therefore, it is important to understand these factors before designing. In this paper, we gathered the available literature on the blast loads on the structures and explained the special problems while defining the loads.
Terrorists attack by explosive loading along border territory by targeting both government buildings and also civilian houses. On the safety issue, the vulnerability of structures to blast loads must be protected. The explosives during a blast release huge kinetic energy and also produce heavy blast waves comprising of the pressure of about 3–5 kPa or even more [1].
1.1 Aims of the Study
The myth of blast is catastrophic causing loss of life and permanent structures. The residuals left after a blast pose threat to the environment for a long period. Increasing blast loads of the twenty-first century like the Beirut explosion and WTC blasts are the burning examples. India had to suffer from Improvised Explosive Device (IED) blasts in 337 numbers (2017), 268 (2015), 190 (2014), 283 (2013) and 365 (2012), respectively, as per NBDC data (National Bomb Data Centre, India). Therefore, it is high time that either we have to think of dissolution methods, or we shall have controlled blasting. For terrorist blast loads, structures must be blast-resistant (The Economic Times news, S. K. Gurung, Jul 12, 2018, 10:34 PM).
1.2 The Objective of the Present Paper
The following are the objectives of the present paper:
-
To review the studies done by the various researchers on blast load effects on different RC and Steel-framed structures.
-
To review various works done on blast effect on framed structures with different irregularities, viz., Geometric, Stiffness, Mass irregularities, etc.
-
To review the blast loads and blast-affected structures.
2 Literature Review
Terrorism is one of the major threats to humanity and its property. Gradually, the Naxal/terrorist groups are becoming unstructured and hostile to use blast loads to attack the public and their structural possessions like bridges, towers and structures.
The summary of timeline key inferences obtained from the various literature survey done from 1995 to 2018 is shown in Table 1.
2.1 Recent Studies on Blast Loads
Kumar et al. [41, 43] studied the performance of symmetric RC space framed buildings subjected to seismic and impact loads. They used time history analysis to study the response of the considered building. From their study, it has been observed that the maximum lateral displacement for a surface blast of 2500 kg TNT and seismic load were comparable at all storey levels. This maximum lateral displacement was obtained at 5 s in buildings subjected to the Northridge earthquake, while it was obtained at 0.5 s in the same building subjected to a surface blast of 2500 kg TNT. Applied Element Method-based software was used for their study.
Vangipuram et al. [44] observed that Blast loads do not act uniformly and may be symmetrical or skew. While designing for blast loads the reflected peak pressure and temperature varies at different points in a structure with diminution of the standoff distance.
Megha and Ramya [45] studied the impact of the blast load on buildings. A six-storey building is considered for the study. The building is modelled using ETABS 2016. The building is subjected to different charge weights of 200 g, 400 and 600 kg with a standoff distance of 20, 40 and 60 m. Blast parameters are determined as per the guidelines of IS:4991–1968. The time history analysis is carried out and the response of the structure is determined in terms of displacement versus time, velocity versus time and acceleration versus time. To make the building more resistible against blast load, shear walls and steel bracings were implemented. The results conclude that the storey displacement, storey drift and column forces are high when the blast is at a distance of 20 m from the building. The displacement and drift are more when the charge weight and distance are less.
Sunita and Bharati [46] have studied the effects of surface blasts on multi-storey buildings. Four seismically designed RC structures with 3, 6, 9 and 12 heights were considered. The parameters considered are standoff distance and charge weight. The non-linear time history analysis is used to obtain the response of the building. For analysis, SAP2000 software has been used. Charge weights of 500 kg TNT and 1000 kg TNT at a standoff distance of 5, 10, 15, 30, 40 and 60 m were considered for analysis. The results conclude that base shear produced by ground shock is greater than the base shear produced by air pressure for all the standoff distances in both high-rise and low-rise buildings. With the increase in charge weight, the effect of the ground shock increases more than air pressure.
2.2 Models Developed
Models are developed for finding the parameters of the shock waves generated by the blast loads based upon the scaled distance, and they are compartmentalized as Airburst (free air) and Surface burst models. The different burst models are the Brode mode (Brode [48]), Henrych and Major mode (Henrych et al. [49]), Held’s Model (Held [50]), Mill’s mode (Mills [51]), Sadovskiy mode (Sadovskiy et al. [52]), Bajie model (Bajie [53]) and Kinny & Graham model (Kinny et al. [54]) which is the development of the US Army TM5-855–1 model [55].
Similarly, the surface burst models developed by different researchers are Newmark & Hansen model (Newmark et al. [56]), Swisdak model (Swisdak [57]), Wu and Hao model (Wu and Hao [58]), Siddiqui and Ahmad model (Siddiqui et al. [59]), Iqbal and Ahmad model (Iqbal et al. [60]) and Badshah model (Badshah [61]).
2.3 Lapses and Research Gap
Investigating the past works, it is ascertained that a large number of works have been done on blast loads on regular and irregular structures, standoff distances and charge weight variations and behaviour on different types of buildings (SIMCON or SIFCON) than RCC structures. However, it is found that the impact on blast loads on the framed structure was meagre.
3 Preface to Blast Loads
3.1 Blast Materials
The blast materials (explosives) are a solid or liquid base that should have the properties as follows: The material is normal at ground state but undergoes a chemical change when stimulated, mainly Tri-nitro Toluene main base structure. This reaction may yield a very high temperature, huge amount of gases and produces explosion and undergoes exothermic reaction. The controlled explosions are intended during quarry blasting, demolition of structures, shaping foundation and tunnel excavation within a mountainous base.
The health issues (trauma/death) associated with improvised explosive device (IED) spasm are overpressure damage (heart, lungs, abdomen and other sensitive organs); fragmentation injuries from flying debris; thermal injuries, impact injuries, fall injuries and toxic exposure injuries (John Pichtel [62]).
3.2 Field Test Results
To have experimented on blast loads, it is difficult to conduct and generally military laboratories are preferred. Field tests are conducted by various researchers for different blast materials and the results are summarized in Table 2.
Regarding Table 2, the notation followed is as follows:
RCC: Reinforced cement concrete;
RC + ACJ: Reinforced concrete with advanced composite jackets;
ALFC: Reinforced cement concrete with aluminium foam claddings;
FRC: Fibre-reinforced concrete;
SFRC: Steel fibre-reinforced concrete;
LCFRC: Long carbon fibre-reinforced concrete.
3.3 Discussion
Structures could not be completely safe and riskless. It is always against a distinct risk level. The distresses occurred to the building by an earthquake, blast loads and hurricane loads can be at a reduced level, and the distresses caused to the building shall be less. The mitigation strategies for the reduction of the threat level from blast loadings are strict surveillance through diligent intelligence, well vigilant security system, enhancing standoff distance between the approach to the target, constructing blast walls for attenuation of shocks, proper landscaping with the optimized alignment of the structure and constructing structural elements, to absorb the blast load impact.
4 Conclusions
After studying the above literature, the following conclusions have been drawn:
-
1.
As the standoff distance increases, the blast pressure decreases and vice versa.
-
2.
As the charge weight increases, the blast pressure increases.
-
3.
The regular structure has higher resistance than the irregular structure.
-
4.
The dynamic behaviour of SIMCON buildings is better than RCC buildings.
-
5.
Dampers or stiffeners can be used to resist such heavy loads, and also joints should be designed to resist such heavy moments.
-
6.
The dynamic behaviour of the SIFCON frame is better than that of the RCC frame.
From the literature review, it has been observed that no studies are made on the performance of Reinforced Concrete Framed structures subjected to blast loads by considering Soil-Structure Interaction.
References
Chiquito, M., Santos, A. P., López, L. M., & Castedo., R. (2019). Blast effects on structural elements. Open access peer-reviewed chapter 257. https://doi.org/10.5772/intechopen.88721.
Dharaneepathy, M. V., Keshava Rao, M. N., Santhakumar, A. R. (1995). Critical distance for blast resistance design. Computer and Structure, 54(4), 587–595. ISSN: 0045–7949.
Tagel-Din., Hatem. (1998). A new efficient method for nonlinear, large deformation and collapse analysis of structures. PhD thesis, Civil Engineering Department The University of Tokyo.
Corely, W. G., Mlakar, P., Sozen, M., Thornton, C. (1998). The Oklahoma city bombing: summary and recommendations for multihazard mitigation. Journal of Performance of Constructed Facilities 12(3), 100–112. ISSN: 0887–3828/eISSN: 1943–5509.
Krauthammer, T., Altenberg, A. (2000). Negative phase blast effects on glass panels. International Journal of Impact Engineering, 24(1), 1–17. ISSN: 0734–743X.
Kauthammer, T. (2002). Development of progressive collapse analysis procedure and condition assessment for structures. paper published by the Pennsylvania State University, US Army Engineer Research and development Centre, Defence Threat Reduction Agency.
Meguro, K., Tagel-Din, H. S. (2002). Applied element method used for large displacement structural analysis. Journal of Natural Disaster Science 24(1), 25–34. ISSN: 0388–4090/e ISSN: 2434–6705.
Remennikov, A. M. (2003). A review of methods for predicting bomb blast effects on buildings. Journal of Battlefield Technology 6(3) 5–10. ISSN: 1440–5113.
Elkholy, S., Meguro, K. (2004). Numerical modelling of steel structures in fire conditions using improved applied element method. Proceedings of the 3rd international symposium on new technologies for urban safety of mega cities in Asia, Kanpur, India.
Luccioni, B. M., Ambrosini, R. D., Danesi, R. F. (2004). Analysis of building collapse under blast loads. ELSEVIER Engineering Structures 63–71.
March, K. A., Farid Al Fawakhiri. (2005). Blast and progressive collapse. fact for Steel Buildings, USA.
Remennikov, A. M., Rose, T. A. (2005). Modelling blast loads on buildings in complex city geometries. Computers and Structures 83(27), 2197–2205. ISSN: 0045–7949.
Pandey, A. K., Kumar, R., Paul, D. K, Trikha, D. N. (2016). Non-linear response of reinforced concrete containment structure under blast loading. Nuclear Engineering and Design 236(9), 993–1002. ISSN: 0029–5493.
Kadid, A., Lahbari, N., Fourar, A. (2007). Blast loaded stiffened plates. Journal of Engineering and Applied Sciences 2(2): 456–461, ISSN: 1816–949x/eISSN: 1818–7803.
Ngo, T., Mendis, P., Gupta. A, Ramsay, J. (2007). Blast loading and blast effects on structures–an overview. EJSE Special Issue: Loading on Structures, 76–91 http://www.ejse.org/Archives/Fulltext/2007/Special/200707.pdf.
Zhu, F., Lu, G. (2007). A review of blast and impact of metallic and sandwich structures. EJSE Special Issue: Loading on Structures, ISSN: 1443–9255.
Van der meer, L. J. (2008). Dynamic response of high rise building structures to blast loading. research report, Eindhoven University of Technology, A-2008.3, O-2008.8.
Moon, N. N. (2009). Prediction of blast loading and its impact on buildings. M. Tech. thesis, National institute of technology, Roukema.
Pichtel, J. (2012). Distribution and fate of military explosives and propellants in soil: a review. Applied Environmental Soil Science. https://doi.org/10.1155/2012/617236
Herrera RG, Soberon, CG (2008) Influence of plan irregularity of buildings. In: 14th World conference on earthquake engineering, China, 53–60.
Koccaz, Z., Sutcu, F. (2008). Architectural and structural design for blast resistant buildings. The 14th world conference on earthquake engineering.
Nasser, A. A., Razaqpur, A. G., Tait, M. J., Campidelli, M., Foo, S. (2010). Evaluation of nonlinear response of steel members under blast loading. 2nd specialty conference on disaster mitigation, Winnipeg, Manitoba.
Hussein, A. T. (2010). Non-linear analysis of SDOF system under blast load. European Journal of Scientific Research, (3), 430–437.
Jayatilake, I. N., Jayasinghe, M. T. R., Thambiratnam, D. P. (2010). Response of tall buildings with symmetric setbacks under blast loading. Journal of the National Science Foundation of Sri Lanka, 115–123.
Raparla, H. B., Bodige, N., Kumar, R. P. (2011). 2D Numerical modeling of progressive collapse during earthquakes: a case study on RC bare frame. Proceedings of international conference on advances in civil engineering, 21–23, INV 1–25, Department of civil engineering, K L University, Guntur Dist., A.P., India.
Khalil, A. (2012). Enhanced modeling of steel structures for progressive collapse analysis using applied element method. Journal of Performance of Constructed Facilities 26(6), 766–779. ISSN: 0887–3828/eISSN: 1943–5509.
Helmy, H., Hamed, S., Sherif, M. (2012). Progressive collapse assessment of framed reinforced concrete structures according to UFC guidelines for alternative path method. Engineering Structures, 42, 127–141. ISSN: 0141–0296.
Al-Ansari, M. S. (2012). Building Response to Blast and Earthquake Loading. International Journal Civil Engineeering Technolnogy (IJCIET), (2), 327–346.
Helmy, H., Hamed, S., Sherif, M. (2013). Computer-aided assessment of progressive collapse of reinforced concrete structures according to GSA code. Journal of Performance of Constructed Facilities, 27(5), 529–539. ISSN: 0887–3828/eISSN: 1943–5509.
Subin, S. J. (2013). Analysis of building under blast. research report, M A college of engineering kothamangalam.
Jayashree, S. M. (2013). Dynamic response of a spaced framed structure subjected to blast load. Journal of Civil and Structural Engineering 4(1).
Coffield, A., Adeli, H. (2014). An investigation of the effectiveness of the framing systems in steel structures subjected to blast loading. Journal of Civil Engineering and Management 20(6), 767–777. ISSN: 1392–3730/eISSN: 1822–3605.
Kulkarni, A. V., Sambireddy, G. (2014). Analysis of blast loading effect on high rise buildings. Civil and Environmental Research 6.
Osman, S., Atef Eraky., Tharwat Sakr., Shimaa Emad. (2014). Response of building structures to blast effects. International Journal of Engineering and Innovative Technology (IJEIT) 4(2).
Coffield, A., Hojjat Adeli. (2016). Irregular steel building structures subjected to blast loading. Journal of Civil Engineering and Management, 22(1), 17–25. ISSN: 1392–3730/eISSN: 1822–3605.
Madonna, J., Vijaya, G. S., Er. Kiran Kumar, K. L. (2016). Analysis of high rise RCC buildings subjected to blast loads. International Research Journal of Engineering and Technology 3(8).
Chiranjeevi, D., Simon, J. (2016). Analysis of reinforced concrete 3D frame under blast loading and check for progressive collapse. Indian Journal of Science and Technology 9.
Habib, M. Z., Alam, M. A., Barua, S., & Islam, M. (2016). Effect of plan irregularity on RC buildings due to BNBC-(2006) earthquake load. International Journal of Scientific and Engineering Research, 7(1), 761–765.
Ratna SK (2016) Analysis of RCC and SIMCON buildings subjected to blast effects. International Journal of Civil Engineering and Technology (IJCIET) 7(4), 223–233.
Kumar,M. P., Rambabu, K. (2017). Performance of RC space frame with vertical setback subjected to seismic and blast load using applied element method.Disaster Advances 10(5), 1–13. ISSN: 0974262X.
Kumar, M. P., Rambabu, K. (2018). Response of regular RC space frame subjected to seismic and blast load using applied element method. Disaster Advances 11(7), ISSN: 0974262X.
Singh, P. (2018). Analysis of vertical irregular building under blast loading. International Journal of Civil Engineering and Technology 9(8).
Kumar, M. P., Krishna, C., Rambabu, K. (2019). Collapse analysis of RC buildings subjected to blast load using AEM. Proceedings of The 18th international symposium on new technologies for urban safety of mega cities in Asia (USMCA–2019), Yangon Technological University, Yangon, Myanmar.
Vangipuram, B., Sharief Md, A. J., Sandeep, B. B., Baraik, S. (2019). Behaviour of reinforced concrete structural members under the influence of implicit blast loading International Journal of Civil Engineering and Technology 10(7), 349–358.
Megha, S. M., Ramya, K. (2019). Analysis of multi-storey RC building subjected to blast load using time history method. International Journal of Innovative Science and Research Technology 4(6)
Sunita, T., Bharati, S. D. (2020). Effect of surface blast on multistory buildings. Journal of Performance of Constructed Facilities 34(2).
Pichtel, J. Distribution and fate of military explosives and propellants in soil: a review. Applied Environmental Soil Science, https://doi.org/10.1155/2012/617236
Brode, H. L. (1955). Numerical solutions of spherical blast waves. Journal of Applied Physics, (6), 766–775.
Henrych, J., Major, R. (1979). The dynamics of explosion and its use. Elsevier, Amsterdam, Netherlands.
Held, M. (1983). Blast waves in free air. Propellants, Explosives, Pyrotechnics, (1), 1–7.
Mills, C. A. (1987). The design of concrete structure to resist explosions and weapon effects. Proceedings of the 1st International conference on concrete for hazard protections, 61–73.
Sadovskiy, M. (2004). A Mechanical effects of air shockwaves from explosions according to experiments Sadovskiy MA Selected Works: Geophysics and Physics of Explosion. Nauka Press.
Bajić, Z. (2007). Determination of TNT equivalent for various explosives. MS. thesis, University of Belgrade, Belgrade, Serbia.
Kinney, G. F., Graham, K. J. (2013). Explosive shocks in air. Springer Science Business Media.
US Army. (1965). Fundamentals of protective design (non-nuclear). Department of Army Technical Manual, TM5–855–1, US Army, Washington, DC, USA.
Newmark, N. M., Hansen, R. J. (1961). Design of blast resistant structures. Shock and vibration handbook 3.
Swisdak, M. M. Jr. (1994) Simplified Kingery Air blast Calculations. Naval Surface Warfare Center, Indian Head, Md, USA.
Wu, C., & Hao, H. (2005). Modeling of simultaneous ground shock and air blast pressure on nearby structures from surface explosions. International Journal of Impact Engineering, (6), 699–717.
Siddiqui, J. I., & Ahmad, S. (2007). Impulsive loading on a concrete structure. Proceedings of the Institution of Civil Engineers: Structures and Buildings, (4), 231–241.
Ahmad, S., Elahi, A., Iqbal, J., Keyani, M. A., & Rahman, A. G. A. (2013). Impulsive loading on reinforced concrete wall. Proceedings of the Institution of Civil Engineers: Structures and Buildings, (3), 153–162.
Badshah, E. (2017). Performance evaluation of clay brick masonry against blast loading. PhD. thesis, University of Engineering Technology (UET) Peshawar Pakistan.
Pichtel, J. (2012). Distribution and fate of military explosives and propellants in soil: a review applied and environmental soil science (2012). Article ID, 617236, 33. https://doi.org/10.1155/2012/617236.
Rodriguez- NiklT., Lee, C. S., Hegemier, G. A, Frieder, H., Seible, F. Experimental performance of concrete columns with composite jackets under blast loading. Journal of Structural Engineering, 138(1), 81–89. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000444.
Wei, J., Quintero, R., Galati, N., Nanni. (2007). A failure modelling of bridge components subjected to blast loading part I: strain rate-dependent damage model for concrete. International Journal of Concrete Structures and Materials (IJCSM), 1(1), 19–28.
Schenker, A., Anteby, I., & Gal, E. (2008). Full-scale field tests of concrete slabs subjected to blast loads. International Journal of Impact Engineering, (3), 184–198.
Yusof, M. A., Norazman, N., Ariffin, A., Mohd Zain, F., Risby, R., Nag, C. (2011). Normal strength steel fiber reinforced concrete subjected to explosive loading. International Journal Sustainable Construction Engineering and Technology, 1, 127–136.
Wang, W., Zhang, D., LuF., Wang, S. C., Tang, F. (2012). Experimental study on scaling the explosion resistance of a one-way square reinforced concrete slab under a close-in blast loading. International Journal of Impact Engineering 49, 158–164.
Tabatabaei, Z. S., Volz, J. S., Baird, J., Gliha, B. P., Keener, D. I. (2013). Experimental and numerical analyses of long carbon fiber reinforced concrete panels exposed to blast loading. International Journal of Impact Engineering 57, 70–80.
Zhao, C. F., & Chen, J. Y. (2013). Damage mechanism and mode of square reinforced concrete slab subjected to blast loading. Theoretical and Applied Fracture Mechanics, 63–64, 54–62.
Rigby, S. E., Tyas, A., Curry, R. J, Langdon GS Experimental measurement of specific impulse distribution and transient deformation of plates subjected to near-field explosive blasts. Experimental Mechanics, 59(2), 163–178.
Makovika, D., & Makovika, D., Jr. (2014). Blast load of building structure. Mechanical Engineering, (21), 11–18.
Makovicka Jr, D., Makovicka, D. Dynamic response of structure under blast load. https://doi.org/10.17265/1934-7359/2016.04.004.
IS 4991: 1968 .(reaffirmed 2003). Indian standard criteria for blast resistant design of structures for explosions above ground, bureau of indian standards, Manak Bhavan. 9 Bahadur Shah Zafar Marg, New Delhi, India, 110002.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2022 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Jasmine, G.V., Ponnada, M.R., Mishra, S.P. (2022). Blast Loads and Their Effects on Structures. In: Loon, L.Y., Subramaniyan, M., Gunasekaran, K. (eds) Advances in Construction Management. Lecture Notes in Civil Engineering, vol 191. Springer, Singapore. https://doi.org/10.1007/978-981-16-5839-6_15
Download citation
DOI: https://doi.org/10.1007/978-981-16-5839-6_15
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-16-5838-9
Online ISBN: 978-981-16-5839-6
eBook Packages: EngineeringEngineering (R0)