Abstract
The paper presents the technology of execution of a fine bubble generator; the air inlets in the water are Ø 0.1 mm and made in silicon plates. The scheme of the experimental installation where this fine bubble generator is fitted is presented. The end of the paper shows the methodology of the researches and the obtained results.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Pătulea AI., Căluşaru I., Băran N.: Researches regarding the measurements of the dissolved concentration in water. Adv. Mater. Res. 550–553, 3388–3394 (2012)
Oprina, G., Pincovschi, I., Băran, G.: Hidro-gazo-dinamica sistemelor de aerare echipate cu generatoare de bule. Editura POLITEHNICA PRESS, Bucuresti (2009)
Oprina, G.: Contributii la hidrodinamica difuzoarelor poroase, teza de doctorat, Facultatea Energetica, Universitatea POLITEHNICA din Bucuresti (2007)
Pătulea, Al.: Teza de doctorat, Influenta parametrilor functionali si arhitecturii generatoarelor de bule fine asupra eficientei instalatiilor de aerare, Facultatea de Inginerie Mecanica si Mecatronica, Universitatea POLITEHNICA din Bucuresti (2012)
Miyahara, T., Matsuha, Y., Takahashi, T.: The size of bubbles generated from perforated plates. Int. Chem. Eng. 23, 517 (1983)
Căluşaru, I., Băran, N., Pătulea, Al.: The influence of the constructive solution of fine bubble generators on the concentration of oxygen dissolved in water. Adv. Mater. 2304, 538–541 (2012). Online available since 2012/Jun/14 at www.scientific.net (2012) Trans Tech Publications, Switzerland
Băran, N., Căluşaru, I.M., Mateescu, G.: Influence of the architecture of fine bubble generators on the variation of the concentration of oxygen dissolved in water. Buletinul Stiintific al Universitatii Politehnica din Bucuresti, Editura Politehnica Press, serie D, Inginerie Mecanica 75(3), 225–236 (2013)
Dobrovicescu, Al., Baran, N., si col.: Bazele termodinamicii tehnice, vol I. Elemente de termodinamica tehnica, Editura Politehnica Press, Bucuresti (2009)
Idelcik, I.E.: Indrumator Pentru Calculul Rezistentelor Hidraulice. Ed. Tehnica, Bucuresti (1984)
Kiselev, P.G.: Indreptar Pentru Calcule Hidraulice. Editura Tehnica, Bucuresti (1988)
Ionascu, G., Comeagă, C.D., Bogatu, L., Sandu, A., Besnea, D.: Modelling of material properties for MEMS structures. J. Optoelectron. Adv. Mater. 13, 998 (2011)
Călușaru, I.M., Baran, N., Pătulea, A.: Determination of dissolved oxygen concentration in stationary water. Rev. Chim. 63, 1312 (2012)
Mateescu, G., Marinescu, A., Băran, N.: A new Constructing Fine Bubbles Generators. Bulletin of the Transylvania University of Brasov, vol. 2, p. 359. Brasov, Romania (2009)
Băran, N., Tănase, B., Rasha, M., Căluşaru, I.M.: Researches regarding the reduction of the water oxygenation time. Termotehnica 2, 100 (2013)
Acknowledgements
This work was supported by a grant of the Romanian National Authority for Scientific Research and Innovation, CCCDI – UEFISCDI, project number Manunet - MNET17/ENER2307-CEBIOTREAT, within PNCDI III.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer International Publishing AG, part of Springer Nature
About this paper
Cite this paper
Dontu, O., Ioana, M.C., Tănase, B., Băran, N., Gheorghe, G.I., Moraru, E. (2019). Researches Regarding the Use of Additive Technologies in the Construction of Water Aeration Elements. In: Gheorghe, G. (eds) Proceedings of the International Conference of Mechatronics and Cyber-MixMechatronics – 2018. ICOMECYME 2018. Lecture Notes in Networks and Systems, vol 48. Springer, Cham. https://doi.org/10.1007/978-3-319-96358-7_3
Download citation
DOI: https://doi.org/10.1007/978-3-319-96358-7_3
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-96357-0
Online ISBN: 978-3-319-96358-7
eBook Packages: Intelligent Technologies and RoboticsIntelligent Technologies and Robotics (R0)