Abstract
The work aimed to develop the Absorption Driven Drug Formulation (ADDF) concept, which is a new approach in formulation development to ensure that the drug product meets the expected absorption rate. The concept is built on the solubility-permeability interplay and the rate of supersaturation as the driving force of absorption. This paper presents the first case study using the ADDF concept where not only dissolution and solubility but also permeation of the drug is considered in every step of the formulation development. For that reason, parallel artificial membrane permeability assay (PAMPA) was used for excipient selection, small volume dissolution-permeation apparatus was used for testing amorphous solid dispersions (ASDs), and large volume dissolution-permeation tests were carried out to characterize the final dosage forms. The API-excipient interaction studies on PAMPA indicated differences when different fillers or surfactants were studied. These differences were then confirmed with small volume dissolution-permeation assays where the addition of Tween 80 to the ASDs decreased the flux dramatically. Also, the early indication of sorbitol’s advantage over mannitol by PAMPA has been confirmed in the investigation of the final dosage forms by large-scale dissolution-permeation tests. This difference between the fillers was observed in vivo as well. The presented case study demonstrated that the ADDF concept opens a new perspective in generic formulation development using fast and cost-effective flux-based screening methods in order to meet the bioequivalence criteria.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
INTRODUCTION
During the process of formulation development for poorly water-soluble active pharmaceutical ingredients (APIs), multiple excipients and formulation strategies are tested, selected, and optimized based on stability, compatibility, safety, economic considerations, and in vivo performance. In vivo performance is one of the most challenging parameters to predict and control during the development process and is one of the last criteria to be tested in the form of bioequivalence study or other in vivo human clinical trials. A method for rapidly predicting in vivo performance throughout all steps of the development process is highly desired as all changes to the composition or the structure can affect the performance. Accordingly any alteration to the formulation for manufacturability, stability, or other reasons potentially invalidates former predictions. According to the USP guideline, dissolution tests should be performed to predict the bioavailability of the drug [1, 2]. The in vitro dissolution tests may overestimate the in vivo precipitation of drugs as the sink condition created by continuous absorption through the lipophilic membranes is not simulated by the simple dissolution apparatus. Therefore simultaneous dissolution-permeability tests may give better in vivo predictions when studying precipitating systems [3,4,5,6]. In the recent years, many important studies were published about the correlation between solubility and permeability [7]. The so-called solubility-permeability interplay, as illustrated through in vitro and in vivo studies, indicate that formulation-associated changes in drug solubility and permeability are inversely proportion when solubility enhancement occurs through an alteration of drug thermodynamic solubility (e.g., via the addition of cyclodextrins, surfactants, and cosolvents) [8,9,10]. The basis for this relationship has been mathematically described [7].
In case of formulations that lead to supersaturation, such as through the use of amorphous form or lipid-based formulations [11, 12] the thermodynamic solubility of the compound is not altered and the permeability remains unchanged. Formulating the API in form of amorphous solid dispersion (ASD) is a possibility to improve not just its dissolution but also the bioavailability of the API [13]. Electrospinning (ES) is an effective technique for the preparation of ASDs. During the manufacturing, nano-/microfibers are created from a viscous polymer solution containing an API using the driving force of an electrostatic field. This method has several advantages: it is a gentle method for the preparation of solid formulations of the various bioactive agent [14, 15]; it can be a part of continuous manufacturing [16, 17]; and compared to the spray-drying, the amorphous structure is more homogenous and stable as a result of electrostatic forces which lead to more effective solvent evaporation [18, 19]. Polymer additives used for electrospinning are responsible for making the API’s supersaturation last longer in solution, but these excipients generally do not modify the equilibrium crystalline solubility of API. In some cases, however, polymers can affect the thermodynamic solubility of the API, as demonstrated in the literature [20].
It shows the importance of the research area that not only countless studies were carried out in the past, but in recent years, international research collaborations were also established between industry, academia, and even regulatory agencies to improve the prediction of the in vivo performance of oral drug products. The OrBiTo project (Oral Bioavailability Tools) was generated across 13 industrial and 14 academic partners. The program aims to increase the understanding of the gastrointestinal absorption process and to develop and validate new, more biorelevant in vitro and in silico methods, which can result in good in vivo prediction [21, 22]. Another research project was funded by the Food and Drug Administration (FDA) to develop an in vivo-relevant in vitro dissolution testing apparatus [23].
In this work, we present a new approach for generic formulation development which ensures that the drug product meets the expected absorption rate and therefore the bioequivalence criteria. The Absorption Driven Drug Formulation (ADDF) concept investigates and considers the excipient effect on absorption from the excipient selection through the entire development process. In the first step, various types of excipient such as surfactants, polymers, and fillers are investigated to explore the interaction between the API and the excipients using the parallel artificial membrane permeability assay (PAMPA). The generated data are used to select the initial excipients for the preparation of the formulations. In the next step, the effects of individual excipient and formulation process are investigated using small volume flux assay. In the final stage of the development, biorelevant volumes are used on the donor side to investigate and compare final dosage forms.
The aim of this work was to demonstrate that using flux experiments in the formulation development from the excipient selection to the testing of final dosage forms helps the generic drug developers to meet the bioequivalence criteria. Further aim was to show that with the help of high-throughput screening tools like PAMPA and small volume flux assays, fast and cost effective formulation development can be achieved when using the ADDF concept.
For our proof of concept study, we have chosen telmisartan (TEL) as a model drug. TEL is an angiotensin II receptor antagonist and therefore used in the treatment of hypertension [24]. It belongs to the second class of Biopharmaceutical Classification System (BCS), having low solubility and high permeability. The solubility of TEL is extremely low and pH-dependent (practically insoluble between pH 3 and 8) [25, 26]. Micardis, the brand name formulation of TEL, which contains the API in amorphous form, was selected as a reference product in the final stage of flux studies. [27]
MATERIALS AND METHODS
Materials
TEL (514 g/mol, structure shown in Fig. 1), buffer components (NaH2PO4, NaOH, NaCl, KCl, HCl), sorbitol, sodium dodecyl sulfate (SDS), polyoxyethylene sorbitan monooleat (Tween 80), and n-dodecane were purchased from Sigma-Aldrich Co. Llc. (St. Louis, MO, USA). Lactose monohydrate was obtained from Meggle Pharma (Wasserburg, Germany). Reagent grade dichloromethane (DCM) and methanol (MeOH) were ordered from Merck Ltd. (Budapest, Hungary). D-mannitol and (2-Hydroxypropyl)-β-cyclodextrin (HPβCD), with the molar substitution degree of 0.64, were provided by Roquette Freres (Lestrem, France). Hydroxypropylmethylcellulose (HPMC 2910) was obtained from Aqualon, Hercules (Zwijndrecht, The Netherlands). Polyvinylpyrrolidone K30 and K90 (PVP K30 and K90) were received from BASF (Ludwigshafen, Germany). Hydroxypropylmethylcellulose acetate succinate (HPMC-AS) polymer was provided by Ashland Inc. (Wilmington, USA). PrismaHT buffer were obtained from Pion Inc. (Billerica, MA, USA). Simulated intestinal fluid (SIF) powder was purchased from Biorelevant.com (London, UK). Telmisartan brand tablets (Micardis 40 mg API/tablet) were purchased from Boehringer Ingelheim International Gmbh (Ingelheim am Rhein, Germany).
Flux Experiments
PAMPA Method for Evaluating the Effect of Formulation Additives
Each well of the top (donor) compartment of 96-well STIRWELL™ PAMPA sandwich (Pion Inc., Billerica MA, USA) was coated with 4 μL of n-dodecane. Before forming the sandwich, the bottom (acceptor) plate was prefilled with 180 μL of pH = 7.4 PrismaHT buffer. The donor plate was filled with 200 μL of FaSSIF buffer with pre-dissolved TEL and formulation additives. The resultant sandwich was incubated at 37°C, and both compartments were stirred at 60 μm (ABL) with Gut-Box™ (Pion Inc., Billerica MA, USA). After 30 min, the PAMPA sandwich was separated, and 100 μL of both the donor and acceptor compartments were transferred to UV plates (UV-star micro plate, clear, flat bottom, half area, Greiner Group AG, Kremsmünster, Austria). UV absorption (230–400 nm) was measured with Tecan Infinite M200 (Tecan Group Ltd., Mannedorf, Switzerland) driven by PAMPA Explorer software™ (Pion Inc., Billerica MA, USA). Three parallel measurements were performed, and the data were measured with six replicates on every single plate.
The flux across the membrane was calculated using the following equation:
where the flux (J) of a drug through the membrane is defined as the amount (n) of drug crossing a unit area (A) perpendicular to its flow per unit time (t).
where the Pe is the effective permeability of the drug and CD is donor concentration.
Small Volume Dissolution-Permeation Measurements with MicroFLUX Apparatus
Electrospun formulations of TEL were tested using μFLUX (Pion Inc., Billerica MA, USA) apparatus which consists of a donor and an acceptor chamber separated by an artificial membrane (PVDF, polyvinylidenfluoride, 0.45 μm, 1.54 cm2) impregnated with 25 μL n-dodecane to form a lipophilic barrier between the donor and acceptor chambers. In case of oral drug delivery, the donor chamber represents the stomach’s condition, while the 18 mL pH 7.4 buffer of acceptor chamber represents the blood circulation. The attempt was started in 16 mL pH 1.6 buffer solution; then after 30 min, media in the dissolution vessel was converted to FaSSIF (pH 6.5) by adding 4 mL of SIF concentrate. Both chambers were stirred at 250 rpm at 37°C to keep the thickness of the unstirred aqueous layer on minimum. In both chambers, the API concentration was followed by immersed UV probes connected to the Rainbow instrument (Pion Inc., Billerica MA, USA). The flux and permeability values were calculated using Eqs. (1) and (2) between 70 and 100 min.
Large Volume Dissolution-Permeation Measurements with MacroFLUX Apparatus
Final dosage forms of TEL were tested using MacroFLUXTM (Pion Inc., Billerica MA, USA). The method used for large-volume flux studies was described in a previous publication by Borbas et al. [28]. The detailed description of the parameters can be found in the supplement as well. The flux and permeability values were calculated using Eqs. (1) and (2) between 70 and 100 min.
Kinetic Solubility Measurements
Note that in the context of this manuscript, solubility measured by this method will be called kinetic solubility because the form of the solid phase precipitating during these assays was not characterized. The concentrated (4 mg/mL) stock solution of TEL was prepared using 1 M NaOH solution as a solvent. Ten milliliters of dissolution medium consisting of equilibrated fasted state simulated intestinal fluid (FaSSIF) buffer containing pre-dissolved additives was stirred at 200 rpm and held at 37°C by circulating water through a heating block mounted to a Pion μDISS™ profiler (Pion Inc., Billerica MA, USA). The stock solution was added in 20 μL aliquots to the dissolution medium. 1 M HCl was used to readjust the pH of the media after every addition of the stock solution. During and after addition of the stock solution, UV probes connected to a Pion Rainbow™ Dynamic Dissolution Monitor® system were used to detect changes in UV spectra, thus enabling the detection of precipitation, which provides information about the kinetic solubility limit.
The zero intercept method (ZIM) was implemented in the AuPRO™ software (Pion Inc., Billerica MA, USA), which was considered a suitable method for detecting the solid nanoparticles in solution. It can be noticed that the second derivative spectrum of a particular compound usually crosses the wavelength axis at specific wavelengths that we will call zero intercept method points or ZIM points (λZIM). The ZIM points are characteristic of the compound and are independent of the concentration. The second derivative values at λZIM are expected to be zero until the compound is fully dissolved. After a critical concentration, solid particles appear in the solution, and a ZIM point shift can be observed [29,30,31]. In case of TEL, the ZIM evaluation was carried out at a wavelength of 318 nm.
Electrospinning
The calculated polymer and TEL amounts were added into 8 mL of the solvent and stirred magnetically (VELP Scientifica, Usmate, Italy) at 600 rpm until the dissolution was complete (Table I). The electrical potential applied on the spinneret electrode (inner diameter 0.8 mm) was 40 kV (NT-65 high voltage DC supply, MA2000 device, Unitronik Ltd, Nagykanizsa, Hungary). A grounded aluminum plate covered with aluminum foil was used as collector (20–30 cm from the spinneret). Polymer solutions were dosed with 5–15mL/h at room temperature (25°C) with an SEP-10S Plus type syringe pump (Aitecs, Vilnius, Lithuania). The compositions of polymer solutions are shown in Table I. Due to the carboxylic group of TEL, it forms sodium salt (TelNa) in the presence of NaOH.
Preparation of Amorphous TEL
The solvent evaporation technique was used for the preparation of amorphous TEL. One hundred sixty milligrams TEL was dissolved into 8 mL of the solvent (1:1 mixture of MeOH and DCM), and the solution was evaporated at room temperature.
Tableting
240 ± 5 mg tablet weights were compressed using a Dott Bonapace CPR6 eccentric tableting machine (Dott Bonapace, Italy), equipped with a 10 mm concave punch. For each tablet, the exact tablet weight and compression force were registered individually. The composition of the tablets is shown in Table II.
RESULTS
The results of the permeability assays and kinetic solubility measurement are described, followed by the results of the in vitro simultaneous dissolution-permeation tests for the formulations of TEL.
Screening of Formulation Additives Based on PAMPA and Kinetic Solubility
PAMPA
At first, an excipient screening on the PAMPA platform was carried out. The excipients of the available TEL formulations and commonly used standard excipients were involved in the investigation of API-excipient interaction. The concentration of the excipients was determined by referring the usual amount of additives in one tablet to 900 mL dissolution media. Due to the experimental differences in the applied doses, the flux data were considered misleading, and the permeability value was used since it is normalized by the donor concentration.
The results in Table III show that in the case of surfactants, significant permeability reduction can be seen compared to the excipient-free case (p value less than 0.05). The reference permeability values in different plates showed low standard deviations. Generally, polymers had a slight, non-significant increasing effect compared to the neat API, but in case of HPMC-AS, the increase in permeability was found to be significant. Finally, mixed effects were experienced with fillers, where in the case of sorbitol and lactose monohydrate, a significant increase was detected, while the addition of mannitol did not impact the permeability of TEL.
Kinetic Solubility
Table IV demonstrates that in the case of surfactants, a significant kinetic solubility increase was detected as compared to the excipient-free case (p value less than 0.05). The polymers did not significantly affect the kinetic solubility of TEL. Finally, it can be seen that mannitol did not significantly influence the solubility, while sorbitol caused a significant decrease in kinetic solubility.
For the later stages of the development, both PVP versions, HPMC-AS, Tween 80, sorbitol, and mannitol were used in the formulation samples after evaluating PAMPA and kinetic solubility results (see the “Discussion” for details).
Preparation of ASDs via Electrospinning
Since TEL has extremely low solubility in the biorelevant pH range of the small intestine, the first commercial formulation of TEL, Micardis contains the drug in amorphous form [32]. For the same reason, the strategy of preparing an amorphous solid dispersion-based formulation of TEL has been selected for the ADDF project. Electrospinning, an emerging technology, has been applied to produce ASDs. Based on the excipient interaction study, mixture of PVP derivatives and HPMC-AS have been selected as a matrix polymer.
For the electrospinning process, first a TEL containing polymer solution had to be created (Table I). Because of the poor water solubility of the APIs, volatile organic solvents or a mixture of organic solvents are typically used. However, in the case of TEL, it was found that it dissolves extremely well in 1 M NaOH solution; therefore, it can be electrospun from aqueous media with higher productivity than from organic solvents (Table V).
For the product to have the appropriate fibrous structure, a mixture of PVP derivatives was used (Table I). The PVP mixture and HPMC-AS were used in the same concentration in the electrospinning solutions. The scanning electron microscopic images of the electrospun samples (see Supplement) confirm the formation of thin fiber structure in the case of the PVP mixture containing formulation, while no fiber formation, only electrospraying, occurred when using HPMC-AS alone (Table V).
Tween 80 was added to optimize surface tension of both polymer solutions [33] which not only helped the formation of fibers but also significantly increased the process yield (Table V).
The amorphization has been confirmed for all the samples by X-ray powder diffraction measurements (see Supplement). Based on the yield of the electrospinning process, only the formulations produced from NaOH solution were further investigated with the small volume flux testing.
Testing of Formulations with Small Volume Dissolution-Permeation Apparatus
The small volume flux assay has been performed on MicroFLUX setup using a media conversion protocol as described in the “Small Volume Dissolution-Permeation Measurements with MicroFLUX Apparatus” section. The dissolution and appearance profile of the TEL containing ASDs are shown in Fig. 2. As shown on the left graph, all four formulations dissolved completely in simulated gastric fluid (SGF) in the first 30 min. The right-side graph demonstrates that the permeation only started after the media conversion because of the charged state of the API in SGF [28]. To investigate the effect of excipients, formulations were compared to the pure amorphous API. Formulations containing Tween 80 show significantly poorer flux values than did formulations without the surfactant (Table VI). Based on their flux results, only the two electrospun formulations which were prepared without surfactant have been selected and moved to the next stage of final dosage form preparation.
The permeability data measured by small volume dissolution-permeation apparatus showed a good agreement with those measured by PAMPA.
Preparation of Final Dosage Forms via Tableting
Based on the early screening of excipients (PAMPA and kinetic solubility), sorbitol was chosen as a model excipient for lowering solubility and increasing permeability, while mannitol was chosen as an inert tablet filler. Tablets were prepared with these two fillers to confirm the expected difference in the final dosage forms as well. Both ASDs chosen for tableting (Tel_Na_HPMC-AS and Tel_Na_PVP) were mixed and pressed with mannitol and sorbitol separately. Therefore, 4 different tablet versions were made varying the polymer and the filler in the tablets (Table II). These tablets were then assayed with the large volume flux apparatus.
Testing of Final Dosage Forms with Large Volume Dissolution-Permeation Apparatus
The MacroFLUX system equipped with in situ fiber optic concentration monitoring was used in this final investigation. The same media conversion protocol as in the case of small volume dissolution-permeation measurements was applied in the dissolution vessel [28]. The dissolution and appearance profile of the TEL formulations are shown in Fig. 3. Micardis, the brand formulation, and the pure amorphous drug were used as references. The donor concentration vs. time curve on the left side of Fig. 3 shows a delay in disintegration and dissolution for the mannitol containing tablets, but they also reached complete dissolution after about 60–70 min. The permeation started after the media conversion, and the flux was constant in the studied timeframe for all the formulations (Fig. 3, right). The permeability data summarized in Table VII gives a quantitative comparison of the formulations and illustrates how the tablet composition influences the membrane transport of the API. Table VII also shows a comparison of permeability data to the pure amorphous drug and the brand product. It can be seen from the p values of Student’s t-tests that 3 formulations out of 4 had significantly higher permeability values than the pure drug.
The effect of the filler was further investigated; therefore, TEL_PVP and TEL_HPMC-AS samples (previously excluded from the study because of their low yield) were also mixed with mannitol and sorbitol. This resulted in 4 different final dosage forms with high polymer content compared to TEL_Na samples but exactly the same filler content. These final dosage forms were then assayed with large volume dissolution-permeation apparatus (see Supplement). Two ways ANOVA analysis of the permeability results showed that while the quality nor the quantity of the polymer had an effect on the permeability of the API, the type of filler (sorbitol/mannitol) significantly affected the data (p = 0.019).
DISCUSSION
Excipient Selection Based on PAMPA and Kinetic Solubility Results
Solubility and permeability properties are best evaluated together because of the interplay between the two parameters [34]. In many cases where the compound is poorly water-soluble, the measurements of thermodynamic solubility are very challenging [35]. Since the solubility of crystalline TEL in FaSSIF media is less than 1 μg/mL, the excipient effect could not be studied using the standard saturation shake flask method [36]. Instead, kinetic solubility measurements were carried out using in situ UV probes [37]. Surfactants (Tween 80 and SDS) caused a significant increase in solubility (Table IV) and a concomitant decrease in permeability (Table III); sorbitol on the other hand showed a decrease in solubility and therefore also increased the permeability of the API. These results agree well with the literature [10, 34].
Testing of ASDs with Small Volume Dissolution-Permeation Apparatus
Although Tween 80 was able to improve the productivity of the electrospinning process by 100% in the case of PVP mixture-based formulation and by 200% in the case of HPMC-AS-based formulation (Table V), the use of solubilizing agent also decreased the flux of the formulation by 39–52% (Table VI). This decrease in flux is expected to result in a decrease in oral bioavailability. However, from a product uniformity, stability and quality point of view beadless fibers like PVP mixture samples are preferable to the beaded fibers observed with the HPMC-AS samples (see SEM images in Supplement). Nevertheless, only negligible differences were observed between the permeability of formulations prepared with different polymers (Table VI). For that reason, both PVP mixture and HPMC-AS containing samples, that do not contain surfactant, were selected and moved to the final stage of product development. The decreased permeability observed in the results in case of Tween containing samples agree well with the effects seen in excipient screening with PAMPA method (Tables III–IV) and with rat intestinal permeability studies.
Testing of Final Dosage Forms with Large Volume Dissolution-Permeation Apparatus
The dissolution profile (Fig. 3) shows that mannitol-containing tablets have slower disintegration and dissolution than the other four formulations. The same phenomenon was shown by Borbas et al. when assaying mannitol containing marketed formulations of TEL as compared to the sorbitol containing reference product [28]. The delay is more pronounced in the case of TEL_Na_HPMC-AS_mannitol formulation, probably because of the poor solubility of the polymer in acidic media.
The permeability data shown in Table VII are in good agreement with the early screening results, where the polymers and mannitol slightly but not significantly enhanced the permeability of the API, while in the case of sorbitol, the enhancement was more pronounced. In these 3 cases, the final increase in permeability seems to be the product of the individual effect of each additive. In the case of TEL_Na_HPMC-AS_mannitol, however, it seems that there might be an interaction between the additives, because not only is the disintegration of the tablet is delayed, but also the permeability of TEL from this formulation is lower than expected based on PAMPA results. Micardis contains PVP and sorbitol as additives. When comparing the electrospun samples to the brand tablet, it can be seen that permeability values of TEL_Na_PVP_sorbitol and Micardis are almost identical (Table VII). This result indicates that formulations with identical qualitative composition showed very similar permeability data. Varying the filler of the tablets, however, led to a slight decrease in permeability as compared to the brand product.
With these results, the early indication of sorbitol’s advantage over mannitol by PAMPA has been confirmed in the investigation of the final dosage forms. This difference between mannitol and sorbitol can be observed in vivo, as the Cmax of the Actavis (mannitol containing generic product) was found lower than the Cmax of Micardis in the bioequivalence study [32]. As the final dosage forms contain relatively low amount of sugar alcohols, which most likely do not affect the GI transit time [38], the lower Cmax value can rather be explained by the permeability change seen in the in vitro setups.
CONCLUSION
The ADDF concept was created to understand the effect of formulation-related decisions on the flux of the API. This paper presents the first case study using the ADDF concept: not only dissolution and solubility but also permeability of the drug is considered in every step of the formulation development.
Kinetic solubility and PAMPA were used for early excipient screening in order to select excipients or additives which improve the permeability of the API. This high-throughput method could successfully describe the solubility-permeability interplay for TEL with the 10 excipients used in this study.
Small-scale dissolution-permeation apparatus was used for testing TEL containing ASDs. The results showed that while the use of surfactants might be advantageous for the electrospinning process from a productivity point of view, it also significantly decreased the permeability of the API. Therefore, there is a risk that it could lower drug oral bioavailability.
The early indication of sorbitol’s advantage over mannitol by PAMPA has been confirmed in the investigation of the final dosage forms by large-scale dissolution-permeation tests. A difference was also observed in vivo between the fillers.
The presented case study showed that the testing of permeability in every step of the development process opens a new perspective of excipient selection and testing of formulations before bioequivalence studies is conducted. The ADDF concept utilizes fast and cost-effective screening methods and therefore may be a helpful new tool for generic drug developers to meet the bioequivalence criteria.
References
In Vitro Metabolismand Transporter Mediated Drug-Drug Interaction Studies Guidance for Industry, 2017. https://www.fda.gov/files/drugs/published/In-Vitro-Metabolism--and-Transporter--Mediated-Drug-Drug-Interaction-Studies-Guidance-for-Industry.pdf. Accessed 04/07/2021.
EMA. Guideline on the investigation of bioequivalence, London. J Physiol. 2010. https://www.ema.europa.eu/en/documents/scientific-guideline/guideline-investigation-bioequivalence-rev1_en.pdf. Accessed 03/04/2021.
Gu CH, Rao D, Gandhi RB, Hilden J, Raghavan K. Using a novel multicompartment dissolution system to predict the effect of gastric pH on the oral absorption of weak bases with poor intrinsic solubility. J Pharm Sci. 2005;94:199–208.
Carlert S, Pålsson A, Hanisch G, Von Corswant C, Nilsson C, Lindfors L, et al. Predicting intestinal precipitation-a case example for a basic BCS class II drug. Pharm Res. 2010;27:2119–30.
Borbás E, Balogh A, Bocz K, Müller J, Kiserdei É, Vigh T, Sinkó B, Marosi A, Halász A, Dohányos Z, Szente L, Balogh GT, Nagy ZK. In vitro dissolution-permeation evaluation of an electrospun cyclodextrin-based formulation of aripiprazole using μFluxTM. Int J Pharm. 2015;491:180–9.
O’Dwyer PJ, Litou C, Box KJ, Dressman JB, Kostewicz ES, Kuentz M, et al. In vitro methods to assess drug precipitation in the fasted small intestine – a PEARRL review. J Pharm Pharmacol. 2019;71:536–56.
Dahan A, Beig A, Lindley D, Miller JM. The solubility–permeability interplay and oral drug formulation design: two heads are better than one. Adv Drug Deliv Rev. Elsevier B.V. 2016;101:99–107.
Miller JM, Beig A, Carr RA, Webster GK, Dahan A. The solubility-permeability interplay when using cosolvents for solubilization: revising the way we use solubility-enabling formulations. Mol Pharm. 2012;9:581–90.
Beig A, Agbaria R, Dahan A. The use of captisol (SBE7-β-CD) in oral solubility-enabling formulations: comparison to HPβCD and the solubility-permeability interplay. Eur J Pharm Sci. Elsevier B.V. 2015;77:73–8.
Borbás E, Sinkó B, Tsinman O, Tsinman K, Kiserdei É, Démuth B, Balogh A, Bodák B, Domokos A, Dargó G, Balogh GT, Nagy ZK. Investigation and mathematical description of the real driving force of passive transport of drug molecules from supersaturated solutions. Mol Pharm. American Chemical Society. 2016;13:3816–26.
Yeap YY, Trevaskis NL, Quach T, Tso P, Charman WN, Porter CJH. Intestinal bile secretion promotes drug absorption from lipid colloidal phases via induction of supersaturation. Mol Pharm. 2013;10:1874–89.
Kuentz M. Drug supersaturation during formulation digestion, including real-time analytical approaches. Adv Drug Deliv Rev. Elsevier B.V. 2019;142:50–61.
Pandi P, Bulusu R, Kommineni N, Khan W, Singh M. Amorphous solid dispersions: an update for preparation, characterization, mechanism on bioavailability, stability, regulatory considerations and marketed products. Int J Pharm. Elsevier. 2020;586:119560.
Vass P, Pantea E, Domokos A, Hirsch E, Domján J, Németh Á, Molnár M, Fehér C, Andersen SK, Vigh T, Verreck G, Csontos I, Marosi G, Nagy ZK. Electrospun solid formulation of anaerobic gut microbiome bacteria. AAPS PharmSciTech. 2020;21:214.
Hirsch E, Pantea E, Vass P, Domján J, Molnár M, Suhajda Á, et al. Probiotic bacteria stabilized in orally dissolving nanofibers prepared by high-speed electrospinning. Food Bioprod Process. Institution of Chemical Engineers. 2021;128:84–94.
Balogh A, Drávavölgyi G, Faragó K, Farkas A, Vigh T, Sóti PL, Wagner I, Madarász J, Pataki H, Marosi G, Nagy ZK. Plasticized drug-loaded melt electrospun polymer mats: characterization, thermal degradation, and release kinetics. J Pharm Sci. 2014;103:1278–87.
Szabó E, Záhonyi P, Gyürkés M, Nagy B, Galata DL, Madarász L, Hirsch E, Farkas A, Andersen SK, Vígh T, Verreck G, Csontos I, Marosi G, Nagy ZK. Continuous downstream processing of milled electrospun fibers to tablets monitored by near-infrared and Raman spectroscopy. Eur J Pharm Sci. 2021;105907:105907.
Szabó E, Záhonyi P, Brecska D, Galata DL, Mészáros LA, Madarász L, Csorba K, Vass P, Hirsch E, Szafraniec-Szczęsny J, Csontos I, Farkas A, van denMooter G, Nagy ZK, Marosi G. Comparison of amorphous solid dispersions of spironolactone prepared by spray drying and electrospinning: the influence of the preparation method on the dissolution properties. Mol Pharm. 2021;18:317–27.
Sóti PL, Bocz K, Pataki H, Eke Z, Farkas A, Verreck G, et al. Comparison of spray drying, electroblowing and electrospinning for preparation of Eudragit E and itraconazole solid dispersions. Int J Pharm. Elsevier B.V. 2015;494:23–30.
Borbás E, Tözsér P, Tsinman K, Tsinman O, Takács-Novák K, Völgyi G, et al. Effect of formulation additives on drug transport through size-exclusion membranes. Mol Pharm. 2018;15:3308–17.
Butler J, Hens B, Vertzoni M, Brouwers J, Berben P, Dressman J, Andreas CJ, Schaefer KJ, Mann J, McAllister M, Jamei M, Kostewicz E, Kesisoglou F, Langguth P, Minekus M, Müllertz A, Schilderink R, Koziolek M, Jedamzik P, et al. In vitro models for the prediction of in vivo performance of oral dosage forms: recent progress from partnership through the IMI OrBiTo collaboration. Eur J Pharm Biopharm. Elsevier. 2019;136:70–83.
Abrahamsson B, McAllister M, Augustijns P, Zane P, Butler J, Holm R, Langguth P, Lindahl A, Müllertz A, Pepin X, Rostami-Hodjegan A, Sjögren E, Berntsson M, Lennernäs H. Six years of progress in the oral biopharmaceutics area – a summary from the IMI OrBiTo project. Eur J Pharm Biopharm. Elsevier. 2020;152:236–47.
Hens B, Sinko P, Job N, Dean M, Al-Gousous J, Salehi N, et al. Formulation predictive dissolution (fPD) testing to advance oral drug product development: an introduction to the US FDA funded ‘21st Century BA/BE’ project. Int J Pharm. 2018;548:120–7.
Kirk JK. Angiotensin II receptor antagonists: their place in therapy. Am Fam Physician. 1999;59:3140–8.
Tran PHL, Tran HTT, Lee BJ. Modulation of microenvironmental pH and crystallinity of ionizable telmisartan using alkalizers in solid dispersions for controlled release. J Control Release. 2008;129:59–65.
Kundu S, Kumari N, Soni SR, Ranjan S, Kumar R, Sharon A, Ghosh A. Enhanced solubility of telmisartan phthalic acid cocrystals within the pH range of a systemic absorption site. ACS Omega. 2018;3:15380–8.
Wagner L, Zsigmond Z, Ujfalussy G, Orban A, Fulop A. WO 2014/091263 Al. Telmisartan containing pharmaceutical composition 2014. https://patentscope.wipo.int/search/en/detail.jsf?docId=WO2014091263. Accessed 05/06/2021.
Borbás E, Nagy ZK, Nagy B, Balogh A, Farkas B, Tsinman O, Tsinman K, Sinkó B. The effect of formulation additives on in vitro dissolution-absorption profile and in vivo bioavailability of telmisartan from brand and generic formulations. Eur J Pharm Sci. 2018;114:310–7.
Attah LE. Highly selective second derivative spectrophotometry for simultaneous determination of iron (II) and copper (II) using 2-ketobutyric acid thiosemicarbazone. Indian J Chem Technol. 2009;16:351–6.
Sriphong L, Chaidedgumjorn A, Chaisuroj K. Derivative spectrophotometry applied to the determination of triprolidine hydrochloride and pseudoephedrine hydrochloride in tablets and dissolution testing. World Acad Sci Eng Technol. 2009;55:573–7.
Tsinman K, Tsinman O, Riebesehl B, Grandeury A, Juhnke M. In situ method for monitoring free drug concentration released from nanoparticles. Poster Present AAPS Annu Meet Expo Oct 14 -18, 2012, Chicago, IL.
BASG. Public Assessment Report (Scientific discussion) of Telmisartan Actavis AT/H/0335/001-003/DC (https://mri.cts-mrp.eu/Human/Downloads/AT_H_0335_002_PAR.pdf). 2016. Accessed 01/06/2021.
Farkas B, Balogh A, Cselkó R, Molnár K, Farkas A, Borbás E, Marosi G, Nagy ZK. Corona alternating current electrospinning: a combined approach for increasing the productivity of electrospinning. Int J Pharm. 2019;561:219–27.
Beig A, Fine-Shamir N, Porat D, Lindley D, Miller JM, Dahan A. Concomitant solubility-permeability increase: vitamin E TPGS vs. amorphous solid dispersion as oral delivery systems for etoposide. Eur J Pharm Biopharm. Elsevier. 2017;121:97–103.
Csicsák D, Borbás E, Kádár S, Tőzsér P, Bagi P, Pataki H, et al. Towards more accurate solubility measurements with real time monitoring: a carvedilol case study. New J Chem. The Royal Society of Chemistry. 2021;45:11618–25.
Baka E, Comer JEA, Takács-Novák K. Study of equilibrium solubility measurement by saturation shake-flask method using hydrochlorothiazide as model compound. J Pharm Biomed Anal. Elsevier. 2008;46:335–41.
Borbás E, Kádár S, Tsinman K, Tsinman O, Csicsák D, Takács-Novák K, Völgyi G, Sinkó B, Pataki H. Prediction of bioequivalence and food effect using flux- and solubility-based methods. Mol Pharm. 2019;16:4121–30.
Matsui K, Takeuchi S, Haruna Y, Yamane M, Shimizu T, Hatsuma Y, et al. Transverse comparison of mannitol content in marketed drug products: Implication for no-effect dose of sugar alcohols on oral drug absorption. J Drug Deliv Sci Technol. Elsevier. 2020;57:101728.
Funding
Open access funding provided by Budapest University of Technology and Economics. This work was supported by the Hungarian Scientific Research Fund (OTKA grant FK-132133) and BME FIKP-BIO by Ministry for Innovation and Technology (ITM). A. Farkas acknowledges the financial support received through the PREMIUM post-doctorate research program of the Hungarian Academy of Sciences, later Eötvös Loránd Research Network. This study was supported by the ÚNKP-21-4 New National Excellence program of the Ministry for Innovation and Technology from the source of the National Research, Development and Innovation Fund.
Author information
Authors and Affiliations
Contributions
ZKN, OT, KT, EB, and BS designed the research and contributed to the interpretation of results. EB, SK, PT, and DC carried out the experiments. BN and AF performed the statistical evaluation. SK, EB, and BS wrote the manuscript. GV and KTN supervised the research and edited the manuscript. All authors edited the final version of the manuscript.
Corresponding authors
Ethics declarations
Competing Interests
The authors declare no competing interests.
Additional information
Guest Editors: Marilyn N. Martinez, Balint Sinko and Fang Wu
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Konstantin Tsinman has passed away. (during 2020 Covid pandemic)
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Kádár, S., Tőzsér, P., Nagy, B. et al. Flux-Based Formulation Development—A Proof of Concept Study. AAPS J 24, 22 (2022). https://doi.org/10.1208/s12248-021-00668-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1208/s12248-021-00668-9