Abstract
We investigate optical field enhancement for a wide mid-infrared range, originating from the excitation of graphene plasmons, by introducing a graded dielectric grating of varying period underneath a graphene monolayer. Excitation of the plasmonic mode can be achieved by illuminating a normal-incidence plane wave on the gratings due to guided-mode resonance. The gratings of varying period enable the excitation of the plasmonic mode with a very high field enhancement factor (to the order of magnitude of 1000) within a wide spectral band, which leads to the frequency-dependent spatially separated localization of the infrared spectrum modes. We also demonstrate that the excitation position of the plasmonic mode can be freely tuned by varying the thickness of the interlayer as well as the chemical potential of the graphene monolayer. This structure enables the design of two-dimensional plasmonic photonic circuits and metamaterials targeted towards numerous potential applications including optoelectronic detectors, light-harvest devices, on-chip optical interconnects, biosensors and light-matter interactions.
Similar content being viewed by others
Introduction
The efficient concentration of optical energy into nanoscale objects and structures and the consequent enhancement of the optical field by optical antennas1, lightning-rod effect2,3 and nanofocusing4 are of great importance in various applications, including sensing5, tip-enhanced Raman spectroscopy6 and optical nonlinearity7. Nano-optical antennas constructed by nanoparticles or nanostructures are able to convert bulk electromagnetic radiation into strongly localized and enhanced plasmonic modes, but such antennas can only operate within a very limited bandwidth near the resonant frequencies1. The local optical field enhancement within a wide spectral band can be achieved using sharp metal corners or tips due to the high local charge densities2,3 and tapered plasmonic waveguide4,8. However, the above-mentioned schemes for optical field enhancement are commonly constructed using tips, tapers, wedges, grooves and cones, which all require complicated and expensive device geometry engineering for practical application.
It would be hugely advantageous to extend the concept of energy concentration to the infrared and THz regime, which would enable significantly increased applications including probing9, spectroscopy10 and chemical analysis11. However, the poor optical confinement of plasmonic structures due to the negligible penetration of the electromagnetic field into the metal in low frequencies severely limits the efficiency and viability of such concepts12. Furthermore, owing to the significant mode mismatch, it is a great challenge to achieve the optical coupling of input radiation-either freely propagating from a laser source or delivered by an optical fiber into a nanoscale plasmonic waveguide-with high efficiency and a wide spectral band13.
Recent concerns regarding plasmonics have been partly shifted to graphene plasmons (GPs)14,15,16. Graphene, whose optical response is characterized by surface conductivity, behaves like thin metal films with negative permittivity at low frequencies via external tunability14,15, exhibiting the capacity to guide the plasmons in the infrared and THz range. In addition to wide-band tunability by varying the surface conductivity, the plasmonic waves in graphene have very large wavevectors as well as extremely high confinement, which enables us to build potential optical devices with dimensions that are significantly below the diffraction limit. Plasmonic wave localization in graphene is also followed by a strong optical field enhancement due to the significant reduction of the group velocity of the GPs17. Therefore, GPs can be anticipated to realize an energy concentration with a nanoscale spatial region at the infrared and THz regime, which has been proved to be a challenge for metallic nanostructures due to the highly delocalized plasmonic mode. So far, several approaches have been proposed to overcome the momentum mismatch, including graphene microribbon arrays18, a nano-sized metalized tip19, attenuated total reflection via Otto geometry20 and guided-mode resonances using an etched diffractive grating21. In this article, we investigate the optical field enhancement of plasmonic modes by introducing a graded grating with varying period underneath the graphene layer. The excitation of the plasmonic mode on the graphene surface can be achieved using a normal-incidence plane wave on diffractive gratings based on the principle of guided-mode resonance. The graded grating enables the excitation of the plasmonic mode within a wide spectral band, which leads to the frequency-dependent spatially separated localization of the infrared spectrum modes. It should be noted that some recent works on the “trapped rainbow” storage of light in metamaterials22,23 and plasmonic grating structures10,16 are closely related to the concept presented in this work.
Results
Direct excitation of the GPs in a graphene monolayer on a uniform diffractive grating substrate
We first consider the dispersive relationship of the plasmonic mode supported by a graphene monolayer on a uniform diffractive grating substrate with a silica layer as the interlayer (UDGS, the inset of Fig. 1). In our work, the thickness of the grating layer, d1, is assumed to be 500 nm. In this case, the grating layer can be treated as infinitely thick since the silicon substrate below the grating does not affect the field distribution of the GPs in the grating/silica/graphene/air system. As the grating period is much smaller than the wavelength of the incident wave, the grating can be approximately modeled as an effective medium with the equivalent permittivity24
where εsilica = 3.9 and εsilicon = 11.9 are the respective permittivities of silica and silicon at the mid-infrared range25 and f = w2/Λ is the filling ratio of the silica.
For the four-layer grating/silica/graphene/air system, the dispersion relation of the GPs can be derived by combining the Maxwell equations and continuous boundary conditions26
where εi and ki = (β2 − εik02)1/2 (i = 1, 2, g, 0) are the permittivities and wavevectors of the grating layer (i = 1), silica (i = 2), graphene (i = g) and air (i = 0), respectively, while β is the propagation constant of the GPs along the x axis. The dispersion relation of the GPs by equation (2) for μc = 0.65 eV is represented by solid lines in Fig. 1, which agrees with the simulation results (denoted by four prisms). Owing to the large wavevector of the GPs on a graphene surface, one can theoretically predict that both of the highly confined optical field and large field enhancements due to the significant reduction of the group velocity of the GPs can be achieved simultaneously. However, only the large wavevector difference between the GPs and a free-space optical wave has to be overcome so that the unique properties of the plasmonic mode can be further exploited. As for the excitation of the GPs on the graphene monolayer shown in the inset of Fig. 1, the grating period Λ should satisfy the phase matching equation
where j is the diffraction order and θ is the incident angle. To excite the plasmonic waves with wavelength λ and the fundamental order j = 1 under the condition of normal incidence θ = 0, the following expression should be satisfied
Figure 2 shows the optical response of the UDGS for different thicknesses of the silica layer, d2, with μc = 0.65 eV and w1 = 62 nm. It can be clearly seen from Fig. 2(a) that there exist two absorption peaks for d2 = 10 nm, which can be attributed to the excitation of the fundamental (j = 1) and third-order (j = 3) plasmonic modes on the graphene surface. The missing second-order (j = 2) mode is here caused by the vanishing dipole moment. The scaling of the resonant wavelength, associated with the grating period, is consistent with equation (3). The absorption peaks become weaker and weaker as d2 increases due to the fact that the overlap between the GPs and the grating reduces as d2 increases and hence reduces the excitation efficiency. The scaling of the fundamental-mode resonant wavelength with respect to the thickness of the silica layer, d2, by finite element method (FEM) simulation agrees with the theoretical results of equation (4), as shown in Fig. 2(b). It is also interesting to note that the value of the resonant wavelength decreases with the increased d2. This is because the effective index of the plasmonic mode in the grating/silica/graphene/air system reduces with the increased thickness of the silica layer, d2. From Figs 2(c,d), we can also see a greatly enhanced plasmonic field on the graphene surface due to the significant reduction of the group velocity of the GPs, while the square of the electric field is approximately 1146 [Fig. 2(c), fundamental mode] and 137 [Fig. 2(d), third-order mode] times larger than the illuminating plane wave. We define the electric field enhancement factor as the ratio of the electric field intensity on the graphene surface (|E|2) and light source (|E0|2). The enhancement level presented here is quantitatively comparable to that reported in plasmonic nanocavity gratings made of nanogrooves in a gold film27. The resonant wavelength decreases with the increased chemical potential for a given grating period [Fig. 3(a)] and increases with the grating period for a fixed chemical potential [Fig. 3(b)]. In both cases, the theoretical prediction significantly agrees with the simulation result.
Direct excitation of broadband GPs in a monolayer graphene on a graded diffractive grating substrate
The UDGS can only excite the GPs on a graphene monolayer within a very narrow bandwidth around the resonant frequency. Bearing in mind that the resonant frequency is dependent on the grating period [Fig. 3(b)], we further propose a graphene monolayer on a graded diffractive grating substrate (GDGS, the inset of Fig. 4) to enlarge the spectral bandwidth of the plasmonic mode. The graded grating is achieved by linearly increasing the width of the silicon layer, w1, along the x direction, while keeping the width of the silica layer, w2, constant. Wide-band plasmonic field enhancement can be anticipated under the illumination of a normal-incidence plane wave. The simulation result shown in Fig. 4 demonstrates that the GPs of different wavelengths are enhanced at different positions on the graphene surface, leading to a plasmonic “trapped rainbow” effect. It should be noted that the present “trapped rainbow” effect is based on the correlative relationship between the excitation wavelength of the plasmonic mode and the grating period due to the guided-wave resonance. This working principle is different from the previously proposed graded-grating based plasmonic waveguides for the “trapped rainbow” effect10,16, where the frequency-dependent spatially separated localization of the plasmonic wave is achieved by adiabatically reducing the group velocity of the plasmonic wave along the propagation direction. Meanwhile, efficient excitation of the GPs can be easily achieved using a normal-incidence plane wave, while it remains very challenging for that in Ref.16. It can also be seen from Fig. 4(a) that the electric field enhancement factor is quantitatively comparable to that for a UDGS and reaches a maximum of 7 um, more than 2000 times larger than that of the incident plane wave. It should be emphasized that the electric field enhancement factor (|E|2/|E0|2) is independent of the power enhancement on the graphene surface, which is proportional to the power of incident light. The average electric field enhancement for the first 3 um in the left region is approximately 1000, but this does not mean the power enhancement is larger than 1 as the power of the incident light source is unchanged. The GPs excited by the silicon grating propagate along the graphene surface and hence suffer an absorption loss from the graphene monolayer. This is why the electric field intensity reaches its maximum value at the center position for each excitation wavelength [vertical dotted lines in Fig. 4(a)], associated with the excitation period of the grating, but shows a gradual reduction as it departs from that center position. However, since the excited GPs will propagate toward both sides, while the right-going plasmon, whose frequency is approaching the cutoff frequency, suffers a larger propagation loss than the left-going one, it is not surprising that the electric field enhancement factor decays more slowly (with higher electric field enhancement) in the left region than in the right region. It should be noted that the field enhancement for λ = 7 μm is much stronger than that for the other two wavelengths (i.e. 8 μm and 9 μm), even in the first 0 ~ 2 μm region. The reason for this can be explained as follows. The plasmon field enhancement at the excitation position for λ = 7 μm is strongest among the three wavelengths as it is validated by the simulation results. The left-going one will experience a GDGS, whose grating period reduces along the propagation direction. A GDGS can be deemed to be a series of uniform UDGS with a constant period, whose propagation loss can be retrieved from the imaginary part of the propagation constant [Im(β) = 2πIm(n)/λ]. The calculated results show that the propagation loss by a UDGS is almost equal for the three wavelengths. For example, the values of Im(β) with λ = 7, 8 and 9 μm at w1 = 20 nm are 1.81 × 105, 1.62 × 105 and 1.46 × 105 m−1, respectively. Additionally, the left-going plasmon for a longer wavelength undergoes a much larger propagation distance between the excitation position and the 0 ~ 2 μm region. As a result, the field enhancement for λ = 7 μm is higher than that for a longer wavelength in the first 0 ~ 2 μm region.
We then consider the influence of the interlayer between the graphene monolayer and the grating on the optical properties of the GPs on the graphene surface, which can be achieved by changing the gap separation, d2. According to equation (4), for a fixed illumination wavelength (λ = 8 μm in our case), a much wider w1 is required to excite the GPs as d2 increases due to the gradual reduction of the value of n [Fig. 5(a)]. The electric field distribution shown in Figs 5(b,d) numerically demonstrates that the position of the enhanced GPs can be varied for a given wavelength associated with the gap separations. However, the overlap between the GPs and the grating is reduced as d2 increases, which hence reduces the effective strength of the grating. Therefore, it is not surprising that the electric field enhancement tends to decrease as d2 increases. The electric field enhancement can reach 4336 when d2 = 0 nm. The existence of a certain fluctuation in the enhancement for d2, in the range of 2.5 nm to 17.5 nm [green solid line in Fig. 5(a)] can be attributed to the fluctuating excitation efficiency of the GPs. As d2 increases from 2.5 nm to 17.5 nm with the step of 2.5 nm, the value of w1 that is used in our design is never exactly equal to the theoretical value [see the inset of Fig. 5(a)]. Moreover, the difference between the two values shows a fluctuation, which finally results in a fluctuation in the field enhancement. It is also interesting to note that the field enhancement is sharply reduced as d2 is further enhanced beyond 26 nm [denoted by the vertical dashed line in Fig. 5(a)]. This is because there does not exist any grating in the GDGS that is capable of exciting the GPs, even for the rightmost grating [see the electric field distributions for d2 = 27.5 nm in Fig. 5(d)]. In addition, we have also estimated the electric field enhancements with the scattering time of 0.1 and 0.5 ps, which more conservatively reflect the practical transport loss of graphene [Fig. 5(e)]. The resultant electric field enhancement still remains high, especially for τ = 0.5 ps. The maximum value of the electric field enhancement at d2 = 0 with τ = 0.5 ps is 1942, approximately 2.2 times smaller than that with τ = 1 ps (4336). The electric field enhancement will decrease to several hundred when the scattering time is further reduced to 0.1 ps. This enhancement level is still quantitatively comparable to that found with previously reported plasmonic nanocavity gratings27.
It should be noted that, for future tuning of the position of the GPs, one feasible approach might be the use of a piezoelectric material as the dielectric interlayer, whose thickness could be temporally modulated by an external electric field. Alternatively, we could also employ a liquid crystal as the interlayer, whose optical properties could be modulated via an external voltage.
In addition, the position of the GPs could be dynamically tuned by varying the graphene’s optical property by external field. This unique feature renders graphene promising for constructing novel active nanophotonic devices14,16,18,28. Figure 6(a) shows the influence of w1 and μc on the excitation wavelength of the GPs for the GDGS in the inset of Fig. 4. Considering that a doping level of 6 × 1013 cm−2, corresponding to a Fermi-level of μc = 0.9 eV, has been achieved experimentally29,30, the assumed range of the chemical potential (0.45–0.85 eV) is realistic. In Fig. 6(a), the value of the excitation wavelength of the GPs, λ, undergoes a blue shift as μc increases for a given w1. The solid curves labeled with numbers depict the contour lines of λ in the w1-μc plane. What makes the present “trapping rainbow” structure unique, as opposed to previous proposals10,16, is that the “trapping” position for each frequency can be shifted simply by varying the chemical potential [Fig. 6(b)].
Discussion
In conclusion, we have presented a proposal for optical field enhancement for a wide mid-infrared range by exciting the plasmonic mode with a graphene monolayer on a graded grating with varying period. Excitation of the plasmonic mode can be realized simply by illuminating a TM polarized plane wave with a normal-incidence on the graded gratings. Since the excitation wavelength is dependent on the grating period, plasmonic waves with different wavelengths can be enhanced at different positions on the graphene surface, associated with the grating period, leading to the plasmonic “rainbow trapping” effect10,16,22,23. The working principle is quite different from those structures used for the “trapped rainbow” effect based on metamaterials and plasmonics10,16,22,23, where the frequency-dependent spatially separated localization of the plasmonic wave is achieved by adiabatically reducing the group velocity of the electromagnetic wave along the propagation direction. We also demonstrate that the excitation position of the plasmonic mode can be freely tuned by varying the thickness of the interlayer as well as the chemical potential of the graphene monolayer. Numerical simulation results concerning the optical properties of the structure are consistent with the theoretical prediction. The present results indicate a significant number of potential applications in graphene-based optical devices, such as optoelectronic detectors, light-harvest devices, on-chip optical interconnects, biosensors and light-matter interactions.
Methods
The optical properties of graphene are typically described by its surface conductivity. The Kubo formula has been widely employed to retrieve its surface conductivity in a series of theoretical and experimental studies on graphene31,32,33
where fd = 1/(1 + exp[(ε − μc)/(kBT)]) is the Fermi-Dirac distribution, ε is the energy, μc is the chemical potential, T is the temperature, e is the electron charge, is the reduced Planck’s constant, kB is the Boltzmann constant, ω is the radian frequency and τ is the momentum relaxation time representing the loss mechanism due to the carrier intraband scattering.
In the mid-infrared range with |μc| ≫ kBT, the surface conductivity of graphene could be approximated as32
In our study, T = 300 K and τ = 1 ps. Considering that in high-quality suspended graphene a DC mobility of μ > 100000 cm2V−1s−1 has been experimentally achieved34, which leads to τ > 1.5 ps, our setting of τ = 1 ps can be said to conservatively reflect the practical transport loss of graphene. However, as a graphene monolayer with a carrier mobility of more than 100000 cm2V−1s−1 is rarely seen in graphene samples in practice, we have also studied the electric field enhancement utilizing a much more realistic scattering time of graphene [see Fig. 5(c)].
By treating the graphene monolayer as an ultra-thin metal film, graphene’s equivalent permittivity can be written as14
where η0 (≈377 Ω) is the impedance of air, k0 is the light wavevector in free space and dg is the thickness of the graphene monolayer (assumed to be 0.5 nm in our work).
To calculate the dispersion relation of the GPs, two-dimensional FEM simulation based on the mode solver of COMSOL is employed. In the simulation, 5-layer meshes are employed to denote the graphene layer while non-uniform meshes with a maximum element size of 500 nm are adopted to represent the other regions besides graphene.
Additional Information
How to cite this article: Zhang, T. et al. Tunable broadband plasmonic field enhancement on a graphene surface using a normal-incidence plane wave at mid-infrared frequencies. Sci. Rep. 5, 11195; doi: 10.1038/srep11195 (2015).
References
Novotny, L. & Van Hulst, N. Antennas for light. Nat. Photonics 5, 83–90 (2011).
Zayats, A. V., Smolyaninov, I. I. & Maradudin, A. A. Nano-optics of surface plasmon polaritons. Phys. Rep. 408, 131–314 (2005).
Verma, P., Ichimura, T., Yano, T., Saito, Y. & Kawata, S. Nano-imaging through tip-enhanced Raman spectroscopy: Stepping beyond the classical limits. Laser Photonics. Rev. 4, 548–561 (2010).
Qiu, W. et al. Nanofocusing of mid-infrared electromagnetic waves on graphene monolayer. Appl. Phys. Lett. 104, 041109 (2014).
Lal, S., Link, S. & Halas, N. J. Nano-optics from sensing to waveguiding. Nat. Photonics 1, 641–648 (2007).
Berweger, S., Atkin, J. M., Olmon, R. L. & Raschke, M. B. Adiabatic tip-plasmon focusing for nano-Raman spectroscopy. J. Phys. Chem. Lett. 1, 3427–3432 (2010).
Davoyan, A. R., Shadrivov, I. V., Zharov, A. A., Gramotnev, D. K. and Kivshar, Y. S. Nonlinear nanofocusing in tapered plasmonic waveguides. Phys. Rev. Lett. 105, 116804 (2010).
Stockman, M. I. Nanofocusing of optical energy in tapered plasmonic waveguides. Phys. Rev. Lett. 93, 137404 (2004).
Knoll, B. & Keilmann, F. Near-field probing of vibrational absorption for chemical microscopy. Nature 399, 134–137 (1999).
Gan, Q., Fu, Z., Ding, Y. & Bartoli, F. Ultrawide-bandwidth slow-light system based on THz plasmonic graded metallic grating structures. Phys. Rev. Lett. 100, 256803 (2008).
Esteban, Ó., González Cano, A., Mizaikoff, B., Díaz Herrera, N. & Navarrete, M. C. Generation of surface plasmons at waveguide surfaces in the mid-infrared region. Plasmonics 7, 647–652 (2012).
Maier, S. A., Andrews, S. R., Martin-Moreno, L. & Garcia-Vidal, F. Terahertz surface plasmon-polariton propagation and focusing on periodically corrugated metal wires. Phys. Rev. Lett. 97, 176805 (2006).
Gramotnev, D. K. & Bozhevolnyi, S. I. Plasmonics beyond the diffraction limit. Nat. Photonics 4, 83–91 (2010).
Vakil, A. & Engheta, N. Transformation optics using graphene. Science 332, 1291–1294 (2011).
Wang, B., Zhang, X., García-Vidal, F. J., Yuan, X. & Teng, J. Strong coupling of surface plasmon polaritons in monolayer graphene sheet arrays. Phys. Rev. Lett. 109, 073901 (2012).
Chen, L., Zhang, T., Li, X. & Wang, G. Plasmonic rainbow trapping by a graphene monolayer on a dielectric layer with a silicon grating substrate. Opt. Express 21, 28628–28637 (2013).
Karalis, A., Lidorikis, E., Ibanescu, M., Joannopoulos, J. & Soljačić, M. Surface-plasmon-assisted guiding of broadband slow and subwavelength light in air. Phys. Rev. Lett. 95, 063901 (2005).
Ju, L. et al. Graphene plasmonics for tunable terahertz metamaterials. Nat. Nanotechnol. 6, 630–634 (2011).
Chen, J. et al. Optical nano-imaging of gate-tunable graphene plasmons. Nature 487, 77 (2012).
Gan, C. H. Analysis of surface plasmon excitation at terahertz frequencies with highly doped graphene sheets via attenuated total reflection. Appl. Phys. Lett. 101, 111609 (2012).
Gao, W., Shu, J., Qiu, C. & Xu, Q. Excitation of plasmonic waves in graphene by guided-mode resonances. ACS nano 6, 7806–7813 (2012).
Tsakmakidis, K. L., Boardman, A. D. & Hess, O. ‘Trapped rainbow’ storage of light in metamaterials. Nature 450, 397–401 (2007).
Hu, H., Ji, D., Zeng, X., Liu, K. & Gan, Q. Rainbow trapping in hyperbolic metamaterial waveguide. Sci. Rep. 3, 1249 (2013).
Zhu, X. et al. Experimental observation of plasmons in a graphene monolayer resting on a two-dimensional subwavelength silicon grating. Appl. Phys. Lett. 102, 131101 (2013).
Palik, E., Handbook of Optical Constants of Solids (Academic, 1991).
Xu, H. J., Lu, W. B., Zhu, W., Dong, Z. G. & Cui, T. J. Efficient manipulation of surface plasmon polariton waves in graphene. Appl. Phys. Lett. 100, 243110 (2012).
Genevet, P. et al. Large enhancement of nonlinear optical phenomena by plasmonic nanocavity gratings. Nano Lett. 10, 4880–4883 (2010).
Liu, M. et al. A graphene-based broadband optical modulator. Nature 474, 64–67 (2011).
Efetov, D. K. & Kim, P. Controlling electron-phonon interactions in graphene at ultrahigh carrier densities. Phys. Rev. Lett. 105, 256805 (2010).
Chen, C. F. et al. Controlling inelastic light scattering quantum pathways in graphene. Nature 471, 617–620 (2011).
Gusynin, V., Sharapov, S. & Carbotte, J. Magneto-optical conductivity in graphene. J. Phys. Condens. Matter 19, 026222 (2006).
Chen, P. Y. & Alù, A. Atomically thin surface cloak using graphene monolayers. ACS nano 5, 5855–5863 (2011).
Li, Z. et al. Dirac charge dynamics in graphene by infrared spectroscopy. Nature Phys. 4, 532–535 (2008).
Bolotin, K. I. et al. Ultrahigh electron mobility in suspended graphene. Solid State Commun. 146, 351–355 (2008).
Acknowledgements
This work is supported by NSFC (Grant No. 11104093 and 11474116), the Specialized Research Fund for the Doctoral Program of Higher Education (SRFDP) (No. 20120142110064) and ‘the Fundamental Research Funds for the Central Universities’, HUST: 2015TS074.
Author information
Authors and Affiliations
Contributions
T.Z. performed the simulation. T.Z. and L.C. wrote the manuscript. L.C. supervised the project and edited the manuscript. All authors discussed the results and reviewed the manuscript.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Zhang, T., Chen, L., Wang, B. et al. Tunable broadband plasmonic field enhancement on a graphene surface using a normal-incidence plane wave at mid-infrared frequencies. Sci Rep 5, 11195 (2015). https://doi.org/10.1038/srep11195
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep11195
- Springer Nature Limited
This article is cited by
-
Flexibly tunable high-quality-factor induced transparency in plasmonic systems
Scientific Reports (2018)
-
Scattering-parameter model analysis of side-coupled plasmonic Fabry–Perot waveguide filters
Applied Physics A (2018)
-
High Sensitivity Nanoplasmonic Sensor Based on Plasmon-Induced Transparency in a Graphene Nanoribbon Waveguide Coupled with Detuned Graphene Square-Nanoring Resonators
Plasmonics (2017)
-
Graphene-spacer-grating-based structure to realize tunable mid-infrared narrow-band plasmonically induced transparency and slow light effect
Applied Physics A (2017)
-
Ultra-compact tunable graphene-based plasmonic multimode interference power splitter in mid infrared frequencies
Science China Information Sciences (2017)