Abstract
Emerging nano-optofluidic devices have allowed a synergetic relation between photonic integrated circuits and microfluidics, allowing manipulation and transport at the realm of nanoscale science. Simultaneously, optical gradient forces have allowed highly precise control of mechanical motion in nano-optomechanical devices. In this report, we show that the repulsive optical forces of the antisymmetric eigenmodes in an optomechanical device, based on a slot-waveguide structure, increases as the refraction index of the fluid medium increases. This effect provides a feasible way to tailor the repulsive optical forces when these nano-optomechanical devices are immersed in dielectric liquids. Furthermore, the total control of the attractive and repulsive optical forces inside liquids may be applied to design novel nanophotonic devices, containing both microfluidic and nanomechanical functionalities, which may find useful applications in several areas, such as biomedical sensors, manipulators and sorters, amongst others.
Similar content being viewed by others
Introduction
Advances in nanosciences and nanotechnologies have emphasized the need for new manipulation and transport techniques at nanoscale. The precise and stable manipulation and transport of nanoparticles, nanoclusters, or molecules is a critical step to advance these areas. In order to overcome these challenges, a wide variety of methods have been proposed; amongst these, the light-matter interaction methods have been drawing attention as, for instance, optofluidic devices1,2. These devices have merged, in a synergic manner, photonic integrated circuits (PICs) with optofluidic transport, for chemistry and biological applications3. Recently, optofluidic devices based on silicon slot waveguides immersed in water have been successfully applied for manipulating and transporting dielectric nanoparticles and DNA molecules using infrared light4,5,6.
On the other hand, optical gradient forces have allowed for the control of nanomechanical dielectric devices7,8. These optical forces originate from electric dipoles moments induced in the dielectric materials by the light intensity gradient of spatial distributions of the guided modes. Optical gradient forces may be either attractive or repulsive, depending on the resulting dipoles phases, which are dictated by the optical and geometrical properties of the structures9. In a dielectric planar (slab) slot waveguide, the symmetric modes lead to attractive forces, whereas the antisymmetric ones lead to repulsive forces10,11. However, in a realistic rectangular cross-section slot waveguide, the optical gradient forces for symmetric modes are still attractive, but for antisymmetric modes they switch from attractive (for narrow gaps) to repulsive (for wide gaps). Therefore, there is a cross-over gap, after what the repulsive optical force emerges9. In this report, we show that it is possible to decrease and even eliminate the cross-over gap, by immersing the nanowaveguide structures in appropriate dielectric fluid media, thus making it possible to tailor the repulsive optical forces.
Results and Discussions
We consider the slot waveguide structure, shown schematically in Fig. 1, which is composed by two high-index (n H ) coupled waveguides, separated by a gap g, immersed in a low-index dielectric medium (n L ). For gap separations much shorter than the decay of the evanescent fields of the individual waveguides, the slot waveguide provides enhancement and high confinement of light inside the gap region, known as slot effect12,13. Due to the geometric simplicity of the planar slot structure, shown in Fig. 1(a), the optical forces can be carried out analytically by using Maxwell’s equations, Poynting vector concept, and Stress Tensor formalism10,11. Alternatively, the optical forces F opt per unity area (length in z-direction and height in y-direction) for the planar structure can be obtained by the following dispersion relation11:
where n eff is the eigenmode effective index, P/h is optical power per unit high in y-direction, and c is the velocity of light in vacuum. On the other hand, the optical force in the rectangular structure shown in Fig. 1(b), is given very similarly by14,15:
Planar slot waveguide analysis
We analyze silicon (n H = 3.4764)16 slot waveguide structures with four different dielectric fluid claddings: air – Air (n L = 1.0003)17, water – H2O (n L = 1.3154)18, carbon disulfide – CS2 (n L = 1.5884)18, and modified methyl iodide – CH3I (n L = 1.7630)19, at a light source wavelength of λ 0 = 1550 nm. The normalized x-component of the electric field spatial distributions, E x (x), for TM polarization, are shown in Fig. 2(a) for the fundamental symmetric mode TM0, and in Fig. 2(b) for the antisymmetric mode TM1, for a planar slot waveguide structure with width w = 310 nm and gap g =100 nm. The results show that the light intensity for the TM0 mode is highly confined in the gap region, due to the discontinuities of the transverse component of the electric at dielectric interfaces – the slot effect12. The amplitude ratio between the electric field inside the gap and that at the waveguides’ interfaces is given by \({{n}_{H}}^{2}/{{n}_{L}}^{2}\); therefore, this discontinuity decreases as the fluid medium index increases. The transverse discontinuity of the electric field for the TM1 mode also decreases as the fluid medium index increases.
The effective index, n eff , and the optical forces, F opt , for the silicon planar slot waveguide, as a function of the gap g are presented in Fig. 3. Figure 3(a and b) show that the effective indexes of both modes increase as the fluid medium refractive index increases. However, the effective index of the TM0 mode decreases as the gap increases, whereas the effective index of the TM1 mode increases. Furthermore, the effective indexes converge asymptotically to specific values as the gap increases to large distances, corresponding to the effective indexes of the individual waveguides in a decoupled system. Figure 3(c and d) show the optical forces for the TM0 and TM1 modes, respectively, for an optical power per unit length of P/h = 20 mW/µm. In planar slot waveguides, the symmetric modes result in attractive (negative) optical forces, whereas the antisymmetric ones result in repulsive (positive) optical forces10,11. For very narrow gaps, neglecting Casimir and van der Waals (dispersions) forces20, the maximum absolute optical force is achieved by the TM0 mode, when the structure is embedded in Air (−3.75 nN/µm 2), due to the enhanced slot effect in this case, and it decreases as the fluid medium refractive index increases, reaching the lowest comparative magnitude (−0.9 nN/µm 2) for CH3I, as shown in Fig. 3(c). On the other hand, the repulsive optical force of the TM1 increases as the medium index increases. The repulsive optical force reaches +20 pN/µm 2 for Air as fluid medium, and it increases to +44 pN/µm 2 for CH3I. This unique behavior cannot be understood neither by the dispersion relation in the Eq. (1) nor by the field distribution shown in Fig. 2(b); however, analyzing the stress tensor version of the optical force, presented in Eq. (1), which shows that, for the TM polarization, the effective index of the antisymmetric mode has a dominant dependence factor, almost proportional to \({{n}_{L}}^{4}\) (see Appendix A).
Rectangular slot waveguide analysis
In contrast with the planar structure, the more realistic rectangular cross-section structure presents finite-dimension restriction in the y-direction. The slot effect occurs for the so-called quasi-TE polarization; the fundamental symmetric eigenmode is called quasi-TE00 12. Similarly to the planar case, the property of increasing the repulsive forces, as the refractive index of the fluid medium increases, also happens to the antisymmetric eigenmodes of rectangular cross-section slot waveguides, as for instance, the quasi-TE01 mode. Figure 4 shows the FEM (Finite Element Method) simulations for the spatial distributions of the normalized major electric field component, E x (x, y), for a silicon rectangular slot waveguide with width w = 280 nm, height h = 240 nm, and gap g = 50 nm; field profiles are shown for the quasi-TE00 (left column) and quasi-TE01 (right column) polarizations, with structures immersed in Air shown in Fig. 4(a,b), H20 (c,d), CS2 (e,f), and CH3I (g,h), respectively. Results show that, for the fluid with the lowest refractive index, the transverse component of the electric field at the quasi-TE00 polarization is highly confined in the gap region and, as the fluid refractive index increases, the field spreads out mostly over the structure. On the other hand, for the antisymmetric eigenmode quasi-TE01, the outer evanescent fields spread out mostly over the fluid as the fluid refractive index increases.
The effective indexes and the optical forces for the symmetric and the antisymmetric eigenmodes at the quasi-TE polarization of the silicon rectangular slot waveguide are presented in Fig. 5. The effective indexes and the optical forces of the quasi-TE00 mode, shown in Fig. 5(a and c), respectively, present similar behaviors of the symmetric TM mode of the planar configuration, Fig. 3(a and c). The attractive optical force in the rectangular slot waveguide is −200 pN/mW/µm in Air and −43 pN/mW/µm in CH3I. On the other hand, Fig. 5(b) shows that the effective index of the quasi-TE01 mode in Air starts to decrease and then it increases again, as the gap increases, in contrast with what occurs in the planar structure. The point where this inversion of the effective index occurs is exactly where the cross-over gap happens, which switches the optical forces from attractive to repulsive as presented in9. However, Fig. 5(d) shows that, as the fluid medium refractive index increases the cross-over gap decreases, until its complete elimination in CH3I, turning the optical force solely repulsive for all gap intervals in rectangular waveguides. It is worth to mention that the cross-over gap, when it exists, represents an unstable point of operation, since it shows a behavior of attractive forces for narrower gaps and repulsive forces for wider gaps; such a condition leads to unique properties that may be exploited for unusual nano-optomechanical applications, such as bistability or memory, besides in manipulation and (bio) sensing, just to mention a few. This effect can also be used in conjunction with other approaches, in order to further increase the repulsive forces21. In addition, it is a feasible alternative to experimental demonstrations of the repulsive optical forces in very narrow gaps22,23. Furthermore, this effect may be applied to balance the attractive van der Waals and Casimir (dispersion) forces in nano-optomechanical structures, as these forces also decrease in liquids20. Therefore, this study also presents the theoretical foundations for tailoring the cross-over gap condition by appropriate design and choice of polarization eigenmode, gap distance and fluid cladding medium, in order to optimize the optomechanical structure for novel applications.
Conclusions
In this report, we have described the behavior of optical forces in rectangular slot waveguides, as the refractive index of the fluid cladding medium varies. The revealed effects were underlined in stress tensor formalism version of the optical gradient forces. We demonstrated that both attractive and repulsive optical forces are feasible in realistic nano-optomechanical devices; we showed that, by increasing the fluid medium refraction index, it is possible to tailor the cross-over gap up to its complete elimination, which turns the optical force totally repulsive in all the gap intervals, for the antisymmetric modes. We have also proposed that the tailoring of the cross-over gap may be exploited for novel nano-optomechanical applications, such as bistability or memory. Finally, we highlight that the possibility of tailoring the attractive and the repulsive optical gradient forces, inside dielectric fluid media, may be applied to design active devices that enable optical-actuated mechanical motions inside nano-optofluidic devices.
Methods
Planar slot waveguides
The effective refractive indexes of the symmetric and antisymmetric modes presented in Fig. 3(a and b), respectively, of the planar slot waveguide, were obtained by solving their respective TM transcendental equations11, for each value of gap at a given fluid medium. Then, the derivatives of the effective indexes were numerically performed to obtain the optical forces shown in Fig. 3(c and d).
Rectangular slot waveguides
The numerical simulations of the rectangular slot waveguide were done by using the finite element method with the RF Module of COMSOL Multiphysics® commercial software platform. The results presented in Figs 4(a–h) and 5(a and b) were simulated using a 2 × 2 µm 2 PEC (Perfect Electric Conductor) boundary condition with a tetrahedral adaptive mesh.
References
Gluckstad, J. Microfluidics: Sorting particles with light. Nat. materials 3, 9–10 (2004).
Psaltis, D., Quake, S. R. & Yang, C. Developing optofluidic technology through the fusion of microfluidics and optics. Nat. 442, 381–6 (2006).
Monat, C., Domachuk, P. & Eggleton, B. J. Integrated optofluidics: A new river of light. Nat. Photonics 1, 106–114 (2007).
Yang, A. H. J., Lerdsuchatawanich, T. & Erickson, D. Forces and transport velocities for a particle in a slot waveguide. Nano Lett. 9, 1182–1188 (2009).
Yang, A. H. J. et al. Optical manipulation of nanoparticles and biomolecules in sub-wavelength slot waveguides. Nat. 457, 71–75 (2009).
Soltani, M. et al. Nanophotonic trapping for precise manipulation of biomolecular arrays. Nat. nanotechnology 9, 448–52 (2014).
Van Thourhout, D. & Roels, J. Optomechanical device actuation through the optical gradient force. Nat. Photonics 4, 211–217 (2010).
Rodriguez, A. W. et al. Classical and fluctuation-induced electromagnetic interactions in micron-scale systems: Designer bonding, antibonding, and Casimir forces. Annalen der Physik 527, 45–80 (2015).
Povinelli, M. L. et al. Evanescent-wave bonding between optical waveguides. Opt. letters 30, 3042–3044 (2005).
Riboli, F., Recati, A., Antezza, M. & Carusotto, I. Radiation induced force between two planar waveguides. Eur. Phys. J. D 46, 157–164 (2008).
Rodrigues, J. R. & Almeida, V. R. Rigorous analysis of optical forces between two dielectric planar waveguides immersed in dielectric fluid media. Annalen der Physik 529, 1600198 (2017).
Almeida, V. R., Xu, Q., Barrios, C. A. & Lipson, M. Guiding and confining light in void nanostructure. Opt. Lett. 29, 1209 (2004).
Xu, Q., Almeida, V. R., Panepucci, R. R. & Lipson, M. Experimental demonstration of guiding and confining light in nanometer-size low-refractive-index material. Opt. Lett. 29, 1626 (2004).
Zhu, L. Frequency dependence of the optical force between two coupled waveguides. Opt. Lett. 34, 2870–2872 (2009).
Rakich, P. T., Popovic, M. A. & Wang, Z. General treatment of optical forces and potentials in mechanically variable photonic systems. Opt. Express 17, 18116 (2009).
Palik, E. D. Handbook of optical constants of solids (Academic Press, 1985).
Ciddor, P. E. Refractive index of air: new equations for the visible and near infrared. Appl. optics 35, 1566–1573 (1996).
Kedenburg, S., Vieweg, M., Gissibl, T. & Giessen, H. Linear refractive index and absorption measurements of nonlinear optical liquids in the visible and near-infrared spectral region. Opt. Mater. Express 2, 1588–1611 (2012).
Cargille - Refractive Index Matching Liquids - GEM Refractometer liquid - Methylene Iodide with dissolved solids. http://www.cargille.com/refractivestandards.shtml (2017).
Rodrigues, J. R., Rosa, F. S. S. & Almeida, V. R. Casimir and Optical Forces Acting on a Silicon NOEMS Device Based on Slot-WaveguideStructure. IEEE Photonics Technol. Lett. 28 (2016).
Oskooi, A., Favuzzi, Pa, Kawakami, Y. & Noda, S. Tailoring repulsive optical forces in nanophotonic waveguides. Opt. letters 36, 4638–40 (2011).
Roels, J. et al. Tunable optical forces between nanophotonic waveguides. Nat. nanotechnology 4, 510–513 (2009).
Li, M., Pernice, W. H. P. & Tang, H. X. Tunable bipolar optical interactions between guided lightwaves. Nat. Photonics 3, 464–468 (2009).
Acknowledgements
This work was supported in part by the Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) through a doctoral scholarship for J. R. Rodrigues and visiting professor sponsorship for V. R. Almeida, and in part by the Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq) under Grant 310855/2016-0 and Grant 483116/2011-4.
Author information
Authors and Affiliations
Contributions
J.R.R. and V.R.A. conceived the idea, J.R.R. performed the simulations and prepared the manuscript. All authors discussed the results and reviewed the manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare that they have no competing interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Rodrigues, J.R., Almeida, V.R. Tailoring Optical Forces Behavior in Nano-optomechanical Devices Immersed in Fluid Media. Sci Rep 7, 14325 (2017). https://doi.org/10.1038/s41598-017-14777-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-017-14777-z
- Springer Nature Limited