Abstract
Roll flattening theory is an important part of plate shape control theories for 20-high mill. In order to improve the accuracy of roll flattening calculation for 20-high mill, a new and more accurate roll flattening model was proposed. In this model, the roll barrel was considered as a finite length semi-infinite body. Based on the boundary integral equation method, the numerical solution of the finite length semi-infinite body under the distributed force was obtained and an accurate roll flattening model was established. Coupled with roll bending model and strip plastic deformation, a new and more accurate plate control model for 20-high mill was established. Moreover, the effects of the first intermediate roll taper angle and taper length were analyzed. The tension distribution calculated by analytical model was consistent with the experimental results.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
H. L. Yu, X. H. Liu, C. Wang, H. D. Park, J. Iron Steel Res. Int. 15 (2008) No. 1, 30–33.
R. J. Roark, Formulas for Stress and Strain, McGraw-Hill, New York, 1954.
Y. Tozawa, M. Ueda, Journal of the Japan Society for Technology of Plasticity 11 (1970) No. 108, 29–37.
H. L. Yu, X. H. Liu, G. T. Lee, Journal of Manufacturing Science and Engineering 130 (2008) No. 1, 0110161–0110167.
J. H. Cho, S. M. Hwang, Journal of Manufacturing Science and Engineering –Transactions of the ASME 136 (2014) No. 1, 204–226.
J. M. Shin, S. I. Han, J. S. Kim, J. Iron Steel Res. Int. 20 (2013) No. 12, 25–32.
C. T. Wang, K. L. Fang, Steel Rolling 22 (2005) No. 4, 14–23.
K. Hara, T. Yamada, K. Takagi, ISIJ Int. 31 (1991) 607–613.
S. Timoshenko, Theory of Elasticity, McGraw-Hill, New York, 1951.
B. Berger, O. Pawelski, P. Funke, Archive for the Iron and Steel Industry, Verlag Stahleisen, Berlin, 1976.
S. X. Zhou, P. Funke, J. Zhong, Steel Res. 67 (1996) No. 5, 200–204.
S. X. Zhou, P. Funke, J. Zhong, C. Plociennik, Steel Res. 67 (1996) No.11, 491–494.
A. Hacquin, P. Montmitonnet, J. P. Guillerault, Eur. J. Mech. 17 (1998) No. 1, 79–106.
J. Liang, K. M. Liew, Int. J. Numer. Meth. Eng. 52 (2001) No.11, 1189–1202.
R. D. Mindlin, Physics 7 (1936) No. 5, 195–202.
H. Xiao, Z. W. Yuan, T. Wang, J. Iron Steel Res. Int. 20 (2013) No. 10, 39–45.
G. D. Wang, The Shape Control and Theory, Metallurgical Industry Press, Beijing, 1986.
J. C. Lian, in: Proceeding of the First International Conference on Steel Rolling, Tokyo, 1980, pp. 713–724.
C. J. Lu, Z. J. Liu, X. H. Liu, G. D. Wang, Research on Iron and Steel 46 (2000) No.3, 32–33.
Author information
Authors and Affiliations
Corresponding authors
Additional information
Foundation Item: Item Sponsored by National Natural Science Foundation of China (51474190); Natural Sceince Foundation of Hebei Province of China (E2015203311)
Rights and permissions
About this article
Cite this article
Yuan, Zw., Xiao, H. Plate Shape Control Theory and Experiment for 20-high Mill. J. Iron Steel Res. Int. 22, 996–1001 (2015). https://doi.org/10.1016/S1006-706X(15)30102-3
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1016/S1006-706X(15)30102-3