Abstract
Micro- and nano-machining technology has been applied in industry to generate high-precision parts with micro/nano-metric accuracy or feature size in the recent decades. Cutting is one of the most powerful manufacturing processes, and the material removal mechanism is urgently demanded by the industry to understand and improve the micro/nano-machining process efficiently at a low cost. This paper presents the recent advances in cutting mechanism and its applicability for predicting the surface generation and chip formation, especially when material is removed in micro- and nanoscale. In addition to the industry-concerned performance parameters, fundamental physical parameters such as stresses, strains, temperatures, phase transformation, minimum uncut chip thickness and size effects are discussed in this paper for the in-depth understanding of the micro/nano-cutting process.
Similar content being viewed by others
References
Masuzawa T (2000) State of the art of micromachining. CIRP Ann Manuf Technol 49(2):473–488. https://doi.org/10.1016/S0007-8506(07)63451-9
Simoneau A, Ng E, Elbestawi MA (2006) Chip formation during microscale cutting of a medium carbon steel. Int J Mach Tools Manuf 46(5):467–481. https://doi.org/10.1016/j.ijmachtools.2005.07.019
Fang FZ, Zhang XD, Weckenmann A, Zhang GX, Evans C (2013) Manufacturing and measurement of freeform optics. CIRP Ann Manuf Technol 62(2):823–846. https://doi.org/10.1016/j.cirp.2013.05.003
Li GH, Xu ZW, Fang FZ, Wu W, Xing XD, Li WL, Liu HZ (2013) Micro cutting of V-shaped cylindrical grating template for roller nano-imprint. J Mater Process Technol 213(6):895–904. https://doi.org/10.1016/j.jmatprotec.2012.12.010
Fang FZ, Wu H, Liu YC (2005) Modelling and experimental investigation on nanometric cutting of monocrystalline silicon. Int J Mach Tools Manuf 45(15):1681–1686. https://doi.org/10.1016/j.ijmachtools.2005.03.010
Rahman MA, Amrun MR, Rahman M, Kumar AS (2017) Variation of surface generation mechanisms in ultra-precision machining due to relative tool sharpness (RTS) and material properties. Int J Mach Tools Manuf 115(Supplement C):15–28. https://doi.org/10.1016/j.ijmachtools.2016.11.003
Fang FZ, Liu B, Xu ZW (2015) Nanometric cutting in a scanning electron microscope. Precis Eng 41:145–152. https://doi.org/10.1016/j.precisioneng.2015.01.009
Yan YD, Sun T, Dong S (2007) Study on effects of tip geometry on AFM nanoscratching tests. Wear 262(3):477–483. https://doi.org/10.1016/j.wear.2006.06.017
Qingliang Z, Tao S, Shen D, Yingchun L (2001) Micro/nano-machining on silicon surface with a modified atomic force microscope. Chin J Mech Eng 14(3):207–211
Mallock A (1881) The action of cutting tools. Proc R Soc Lond 33(216–219):127–139
Shaw M (2005) Metal cutting principles—Oxford series on advanced manufacturing. Publ Oxford University Press, New York
Ernst H, Merchant M (1941) Surface treatment of metals. American Society of Metals, New York
Merchant ME (1945) Mechanics of the metal cutting process. I. Orthogonal cutting and a type 2 chip. J Appl Phys 16(5):267–275
Merchant ME (1945) Mechanics of the metal cutting process. II. Plasticity conditions in orthogonal cutting. J Appl Phys 16(6):318–324
Lee E, Shaffer B (1951) The theory of plasticity applied to a problem of machining. J Appl Mech 18(4):405–413
Oxley PLB, Hastings WF (1977) Predicting the strain rate in the zone of intense shear in which the chip is formed in machining from the dynamic flow stress properties of the work material and the cutting conditions. Proc R Soc Lond Math Phys Sci 356(1686):395–410. https://doi.org/10.1098/rspa.1977.0141
Fang N, Jawahir IS, Oxley PLB (2001) A universal slip-line model with non-unique solutions for machining with curled chip formation and a restricted contact tool. Int J Mech Sci 43(2):557–580. https://doi.org/10.1016/S0020-7403(99)00117-4
Fang N, Jawahir IS (2002) An analytical predictive model and experimental validation for machining with grooved tools incorporating the effects of strains, strain-rates, and temperatures. CIRP Ann Manuf Technol 51(1):83–86. https://doi.org/10.1016/S0007-8506(07)61471-1
Fang N (2003) Slip-line modeling of machining with a rounded-edge tool—Part I: new model and theory. J Mech Phys Solids 51(4):715–742. https://doi.org/10.1016/S0022-5096(02)00060-1
Fang N (2003) Slip-line modeling of machining with a rounded-edge tool—part II: analysis of the size effect and the shear strain-rate. J Mech Phys Solids 51(4):743–762. https://doi.org/10.1016/S0022-5096(02)00061-3
Arrazola PJ, Özel T, Umbrello D, Davies M, Jawahir IS (2013) Recent advances in modelling of metal machining processes. CIRP Ann Manuf Technol 62(2):695–718. https://doi.org/10.1016/j.cirp.2013.05.006
Abouridouane M, Klocke F, Lung D, Adams O (2012) A new 3D multiphase FE model for micro cutting ferritic–pearlitic carbon steels. CIRP Ann Manuf Technol 61(1):71–74. https://doi.org/10.1016/j.cirp.2012.03.075
Abouridouane M, Klocke F, Lung D (2014) Microstructure-based 3D FE modeling for micro cutting ferritic-pearlitic carbon steels. In: ASME 2014 international manufacturing science and engineering conference collocated with the JSME 2014 international conference on materials and processing and the 42nd North American manufacturing research conference, 2014. American Society of Mechanical Engineers, pp V001T001A008–V001T001A008
Roters F, Eisenlohr P, Hantcherli L, Tjahjanto DD, Bieler TR, Raabe D (2010) Overview of constitutive laws, kinematics, homogenization and multiscale methods in crystal plasticity finite-element modeling: theory, experiments, applications. Acta Mater 58(4):1152–1211. https://doi.org/10.1016/j.actamat.2009.10.058
Jung J-H, Na Y-S, Cho K-M, Dimiduk DM, Choi YS (2015) Microcompression behaviors of single crystals simulated by crystal plasticity finite element method. Metall Mater Trans A 46(11):4834–4840. https://doi.org/10.1007/s11661-015-3092-0
Liu Q, Roy A, Tamura S, Matsumura T, Silberschmidt VV (2016) Micro-cutting of single-crystal metal: finite-element analysis of deformation and material removal. Int J Mech Sci 118:135–143. https://doi.org/10.1016/j.ijmecsci.2016.09.021
Tajalli SA, Movahhedy MR, Akbari J (2014) Simulation of orthogonal micro-cutting of FCC materials based on rate-dependent crystal plasticity finite element model. Comput Mater Sci 86:79–87. https://doi.org/10.1016/j.commatsci.2014.01.016
Niesłony P, Grzesik W, Chudy R, Habrat W (2015) Meshing strategies in FEM simulation of the machining process. Arch Civ Mech Eng 15(1):62–70. https://doi.org/10.1016/j.acme.2014.03.009
Abolfazl Zahedi S, Demiral M, Roy A, Silberschmidt VV (2013) FE/SPH modelling of orthogonal micro-machining of fcc single crystal. Comput Mater Sci 78:104–109. https://doi.org/10.1016/j.commatsci.2013.05.022
Shimada S, Ikawa N, Tanaka H, Ohmori G, Uchikoshi J, Yoshinaga H (1993) Feasibility study on ultimate accuracy in microcutting using molecular dynamics simulation. CIRP Ann Manuf Technol 42(1):91–94. https://doi.org/10.1016/S0007-8506(07)62399-3
Shimada S, Ikawa N, Tanaka H, Uchikoshi J (1994) Structure of micromachined surface simulated by molecular dynamics analysis. CIRP Ann Manuf Technol 43(1):51–54. https://doi.org/10.1016/S0007-8506(07)62162-3
Plimpton S (1995) Fast parallel algorithms for short-range molecular dynamics. J Comput Phys 117(1):1–19. https://doi.org/10.1006/jcph.1995.1039
Humphrey W, Dalke A, Schulten K (1996) VMD: visual molecular dynamics. J Mol Graph 14(1):33–38. https://doi.org/10.1016/0263-7855(96)00018-5
Alexander S (2010) Visualization and analysis of atomistic simulation data with OVITO–the open visualization tool. Modell Simul Mater Sci Eng 18(1):015012
Honeycutt JD, Andersen HC (1987) Molecular dynamics study of melting and freezing of small Lennard–Jones clusters. J Phys Chem 91(19):4950–4963. https://doi.org/10.1021/j100303a014
Alexander S, Vasily VB, Athanasios A (2012) Automated identification and indexing of dislocations in crystal interfaces. Modell Simul Mater Sci Eng 20(8):085007
Goel S, Luo X, Reuben RL, Pen H (2012) Influence of temperature and crystal orientation on tool wear during single point diamond turning of silicon. Wear 284–285:65–72. https://doi.org/10.1016/j.wear.2012.02.010
Oluwajobi A, Chen X (2011) The effect of interatomic potentials on the molecular dynamics simulation of nanometric machining. Int J Autom Comput 8(3):326–332. https://doi.org/10.1007/s11633-011-0588-y
Erhart P, Albe K (2005) Analytical potential for atomistic simulations of silicon, carbon, and silicon carbide. Phys Rev B 71(3):035211
Tersoff J (1989) Modeling solid-state chemistry: interatomic potentials for multicomponent systems. Phys Rev B 39(8):5566–5568
Tersoff J (1990) Erratum: modeling solid-state chemistry: interatomic potentials for multicomponent systems. Phys Rev B 41(5):3248
Goel S, Luo X, Agrawal A, Reuben RL (2015) Diamond machining of silicon: a review of advances in molecular dynamics simulation. Int J Mach Tool Manuf. https://doi.org/10.1016/j.ijmachtools.2014.09.013
Pastewka L, Klemenz A, Gumbsch P, Moseler M (2013) Screened empirical bond-order potentials for Si-C. Phys Rev B 87(20):205410
Zhang J, Zhang J, Wang Z, Hartmaier A, Yan Y, Sun T (2017) Interaction between phase transformations and dislocations at incipient plasticity of monocrystalline silicon under nanoindentation. Comput Mater Sci 131:55–61. https://doi.org/10.1016/j.commatsci.2017.01.043
Vashishta P, Kalia RK, Nakano A, Rino JP (2007) Interaction potential for silicon carbide: a molecular dynamics study of elastic constants and vibrational density of states for crystalline and amorphous silicon carbide. J Appl Phys 101(10):103515. https://doi.org/10.1063/1.2724570
Kikuchi H, Kalia RK, Nakano A, Vashishta P, Branicio PS, Shimojo F (2005) Brittle dynamic fracture of crystalline cubic silicon carbide (3C-SiC) via molecular dynamics simulation. J Appl Phys 98(10):103524. https://doi.org/10.1063/1.2135896
Xiao G, To S, Zhang G (2015) Molecular dynamics modelling of brittle–ductile cutting mode transition: case study on silicon carbide. Int J Mach Tools Manuf 88:214–222. https://doi.org/10.1016/j.ijmachtools.2014.10.007
Sun X, Chen S, Cheng K, Huo D, Chu W (2006) Multiscale simulation on nanometric cutting of single crystal copper. Proc Inst Mech Eng Part B J Eng Manuf 220(7):1217–1222. https://doi.org/10.1243/09544054JEM540SC
Pen HM, Liang YC, Luo XC, Bai QS, Goel S, Ritchie JM (2011) Multiscale simulation of nanometric cutting of single crystal copper and its experimental validation. Comput Mater Sci 50(12):3431–3441. https://doi.org/10.1016/j.commatsci.2011.07.005
Ernst U, Merchant M (1941) Chip formation, friction and high quality machined surface. American Society of Metal, Russell Township
Weule H, Hüntrup V, Tritschler H (2001) Micro-cutting of steel to meet new requirements in miniaturization. CIRP Ann Manuf Technol 50(1):61–64. https://doi.org/10.1016/S0007-8506(07)62071-X
Özel T (2009) Computational modelling of 3D turning: influence of edge micro-geometry on forces, stresses, friction and tool wear in PcBN tooling. J Mater Process Technol 209(11):5167–5177. https://doi.org/10.1016/j.jmatprotec.2009.03.002
Denkena B, Lucas A, Bassett E (2011) Effects of the cutting edge microgeometry on tool wear and its thermo-mechanical load. CIRP Ann Manuf Technol 60(1):73–76. https://doi.org/10.1016/j.cirp.2011.03.098
Özel T, Karpat Y, Srivastava A (2008) Hard turning with variable micro-geometry PcBN tools. CIRP Ann Manuf Technol 57(1):73–76. https://doi.org/10.1016/j.cirp.2008.03.063
Denkena B, Biermann D (2014) Cutting edge geometries. CIRP Ann Manuf Technol 63(2):631–653. https://doi.org/10.1016/j.cirp.2014.05.009
Chien KL (1953) The influence of tool sharpness on the mechanics of metal cutting (PhD). Massachusetts Instiute of Technology, Cambridge
Albrecht P (1960) New developments in the theory of the metal-cutting process: part I. The ploughing process in metal cutting. J Eng Ind 82(4):348–357. https://doi.org/10.1115/1.3664242
Masuko M (1953) Fundamental researches on the metal cutting. I. A new analysis of cutting force. Trans Soc Mech Eng (Japan) 19:32–39
Wyen C-F, Knapp W, Wegener K (2011) A new method for the characterisation of rounded cutting edges. Int J Adv Manuf Technol 59(9):899–914. https://doi.org/10.1007/s00170-011-3555-4
Wyen CF, Wegener K (2010) Influence of cutting edge radius on cutting forces in machining titanium. CIRP Ann Manuf Technol 59(1):93–96. https://doi.org/10.1016/j.cirp.2010.03.056
Denkena B, Reichstein M, Brodehl J, de León García L (2005) Surface preparation, coating and wear performance of geometrically defined cutting edges. In: Proceedings of the 5th international conference the coatings in manufacturing engineering, 2005. pp 5–7
Yussefian NZ, Koshy P (2013) Parametric characterization of the geometry of honed cutting edges. Precis Eng 37(3):746–752. https://doi.org/10.1016/j.precisioneng.2013.02.007
Denkena B, Koehler J, Rehe M (2012) Influence of the honed cutting edge on tool wear and surface integrity in slot milling of 42CrMo4 steel. Proc CIRP 1:190–195. https://doi.org/10.1016/j.procir.2012.04.033
Xu F, Wang J, Fang F, Zhang X (2017) A study on the tool edge geometry effect on nano-cutting. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-016-9922-4
Zong WJ, Li D, Sun T, Cheng K (2006) Contact accuracy and orientations affecting the lapped tool sharpness of diamond cutting tools by mechanical lapping. Diam Relat Mater 15(9):1424–1433. https://doi.org/10.1016/j.diamond.2005.10.066
Moriwaki T (1989) Machinability of copper in ultra-precision micro diamond cutting. CIRP Ann Manuf Technol 38(1):115–118. https://doi.org/10.1016/S0007-8506(07)62664-X
Soãres S (2003) Nanometer edge and surface imaging using optical scatter. Precis Eng 27(1):99–102. https://doi.org/10.1016/S0141-6359(02)00185-X
Born DK, Goodman WA (2001) An empirical survey on the influence of machining parameters on tool wear in diamond turning of large single-crystal silicon optics. Precis Eng 25(4):247–257. https://doi.org/10.1016/S0141-6359(00)00069-6
Shi M, Lane B, Mooney CB, Dow TA, Scattergood RO (2010) Diamond tool wear measurement by electron-beam-induced deposition. Precis Eng 34(4):718–721. https://doi.org/10.1016/j.precisioneng.2010.03.009
Fang FZ (1998) Nano-turning of single crystal silicon. J Mater Process Technol 82(1–3):95–101. https://doi.org/10.1016/S0924-0136(98)00024-7
Li XP, Rahman M, Liu K, Neo KS, Chan CC (2003) Nano-precision measurement of diamond tool edge radius for wafer fabrication. J Mater Process Technol 140(1–3):358–362. https://doi.org/10.1016/S0924-0136(03)00757-X
Gao W, Motoki T, Kiyono S (2006) Nanometer edge profile measurement of diamond cutting tools by atomic force microscope with optical alignment sensor. Precis Eng 30(4):396–405. https://doi.org/10.1016/j.precisioneng.2005.11.008
Gao W, Asai T, Arai Y (2009) Precision and fast measurement of 3D cutting edge profiles of single point diamond micro-tools. CIRP Ann Manuf Technol 58(1):451–454. https://doi.org/10.1016/j.cirp.2009.03.009
Bassett E, Köhler J, Denkena B (2012) On the honed cutting edge and its side effects during orthogonal turning operations of AISI1045 with coated WC-Co inserts. CIRP J Manufact Sci Technol 5(2):108–126. https://doi.org/10.1016/j.cirpj.2012.03.004
Shimizu Y, Asai T, Gao W (2011) Evaluation of nanometer cutting tool edge for nanofabrication. INTECH Open Access Publisher, Croatia
Yen Y-C, Jain A, Altan T (2004) A finite element analysis of orthogonal machining using different tool edge geometries. J Mater Process Technol 146(1):72–81. https://doi.org/10.1016/S0924-0136(03)00846-X
Klocke F, Kratz H (2005) Advanced tool edge geometry for high precision hard turning. CIRP Ann Manuf Technol 54(1):47–50. https://doi.org/10.1016/S0007-8506(07)60046-8
Tang X, Nakamoto K, Obata K, Takeuchi Y (2013) Ultraprecision micromachining of hard material with tool wear suppression by using diamond tool with special chamfer. CIRP Ann Manuf Technol 62(1):51–54. https://doi.org/10.1016/j.cirp.2013.03.094
Thiele JD, Melkote SN (1999) Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel. J Mater Process Technol 94(2–3):216–226. https://doi.org/10.1016/S0924-0136(99)00111-9
M’Saoubi R, Chandrasekaran H (2004) Investigation of the effects of tool micro-geometry and coating on tool temperature during orthogonal turning of quenched and tempered steel. Int J Mach Tools Manuf 44(2–3):213–224. https://doi.org/10.1016/j.ijmachtools.2003.10.006
Childs THC (2010) Surface energy, cutting edge radius and material flow stress size effects in continuous chip formation of metals. CIRP J Manufact Sci Technol 3(1):27–39. https://doi.org/10.1016/j.cirpj.2010.07.008
Jiwang Y, Hongwei Z, Tsunemoto K (2009) Effects of tool edge radius on ductile machining of silicon: an investigation by FEM. Semicond Sci Technol 24(7):075018
Ng CK, Melkote SN, Rahman M, Senthil Kumar A (2006) Experimental study of micro- and nano-scale cutting of aluminum 7075-T6. Int J Mach Tools Manuf 46(9):929–936. https://doi.org/10.1016/j.ijmachtools.2005.08.004
Liu K, Melkote SN (2007) Finite element analysis of the influence of tool edge radius on size effect in orthogonal micro-cutting process. Int J Mech Sci 49(5):650–660. https://doi.org/10.1016/j.ijmecsci.2006.09.012
Fang FZ, Chen LJ (2000) Ultra-precision cutting for ZKN7 glass. CIRP Ann Manuf Technol 49(1):17–20. https://doi.org/10.1016/S0007-8506(07)62887-X
Fang FZ, Venkatesh VC, Zhang GX (2002) Diamond turning of soft semiconductors to obtain nanometric mirror surfaces. Int J Adv Manuf Technol 19(9):637–641. https://doi.org/10.1007/s001700200107
Fang FZ, Zhang GX (2003) An experimental study of edge radius effect on cutting single crystal silicon. Int J Adv Manuf Technol 22(9):703–707. https://doi.org/10.1007/s00170-003-1593-2
Fang FZ, Xu FF, Lai M (2015) Size effect in material removal by cutting at nano scale. Int J Adv Manuf Technol 80(1–4):591–598. https://doi.org/10.1007/s00170-015-7032-3
Ranganath S, Campbell AB, Gorkiewicz DW (2007) A model to calibrate and predict forces in machining with honed cutting tools or inserts. Int J Mach Tools Manuf 47(5):820–840. https://doi.org/10.1016/j.ijmachtools.2006.06.019
Lucca DA, Seo YW, Komanduri R (1993) Effect of tool edge geometry on energy dissipation in ultraprecision machining. CIRP Ann Manuf Technol 42(1):83–86. https://doi.org/10.1016/S0007-8506(07)62397-X
Fang FZ, Wu H, Liu XD, Liu YC, Ng ST (2003) Tool geometry study in micromachining. J Micromech Microeng 13(5):726
Storch B, Zawada-Tomkiewicz A (2012) Distribution of unit forces on the tool edge rounding in the case of finishing turning. Int J Adv Manuf Technol 60(5–8):453–461. https://doi.org/10.1007/s00170-011-3617-7
Woon KS, Rahman M, Fang FZ, Neo KS, Liu K (2008) Investigations of tool edge radius effect in micromachining: a FEM simulation approach. J Mater Process Technol 195(1–3):204–211. https://doi.org/10.1016/j.jmatprotec.2007.04.137
Fang FZ, Venkatesh VC (1998) Diamond cutting of silicon with nanometric finish. CIRP Ann Manuf Technol 47(1):45–49
Liu K, Li XP, Rahman M, Neo KS, Liu XD (2007) A study of the effect of tool cutting edge radius on ductile cutting of silicon wafers. Int J Adv Manuf Technol 32(7–8):631–637. https://doi.org/10.1007/s00170-005-0364-7
Arefin S, Li XP, Rahman M, Liu K (2007) The upper bound of tool edge radius for nanoscale ductile mode cutting of silicon wafer. Int J Adv Manuf Technol 31(7–8):655–662. https://doi.org/10.1007/s00170-005-0245-0
Li X, Cai M, Rahman M, Liang S (2010) Study of the upper bound of tool edge radius in nanoscale ductile mode cutting of silicon wafer. Int J Adv Manuf Technol 48(9–12):993–999. https://doi.org/10.1007/s00170-009-2347-6
Ji CH, Shi J, Liu ZQ, Wang YC (2013) Comparison of tool–chip stress distributions in nano-machining of monocrystalline silicon and copper. Int J Mech Sci 77:30–39. https://doi.org/10.1016/j.ijmecsci.2013.09.024
Hosseini SV, Vahdati M (2012) Modeling the effect of tool edge radius on contact zone in nanomachining. Comput Mater Sci 65:29–36. https://doi.org/10.1016/j.commatsci.2012.06.037
Fang FZ, Lee LC, Liu XD (2005) Mean flank temperature measurement in high speed dry cutting of magnesium alloy. J Mater Process Technol 167(1):119–123. https://doi.org/10.1016/j.jmatprotec.2004.10.002
Davies MA, Ueda T, M’Saoubi R, Mullany B, Cooke AL (2007) On the measurement of temperature in material removal processes. CIRP Ann Manuf Technol 56(2):581–604. https://doi.org/10.1016/j.cirp.2007.10.009
Vernaza-Peña KM, Mason JJ, Li M (2002) Experimental study of the temperature field generated during orthogonal machining of an aluminum alloy. Exp Mech 42(2):221–229. https://doi.org/10.1007/bf02410886
Sutter G, Ranc N (2007) Temperature fields in a chip during high-speed orthogonal cutting—an experimental investigation. Int J Mach Tools Manuf 47(10):1507–1517. https://doi.org/10.1016/j.ijmachtools.2006.11.012
Abukhshim NA, Mativenga PT, Sheikh MA (2006) Heat generation and temperature prediction in metal cutting: a review and implications for high speed machining. Int J Mach Tools Manuf 46(7–8):782–800. https://doi.org/10.1016/j.ijmachtools.2005.07.024
Akbar F, Mativenga P, Sheikh MA (2010) An experimental and coupled thermo-mechanical finite element study of heat partition effects in machining. Int J Adv Manuf Technol 46(5–8):491–507. https://doi.org/10.1007/s00170-009-2117-5
Outeiro JC, Dias AM, Jawahir IS (2006) On the effects of residual stresses induced by coated and uncoated cutting tools with finite edge radii in turning operations. CIRP Ann Manuf Technol 55(1):111–116. https://doi.org/10.1016/S0007-8506(07)60378-3
Yi Karpat, Tr Özel (2008) Mechanics of high speed cutting with curvilinear edge tools. Int J Mach Tools Manuf 48(2):195–208. https://doi.org/10.1016/j.ijmachtools.2007.08.015
Cai MB, Li XP, Rahman M (2007) Study of the temperature and stress in nanoscale ductile mode cutting of silicon using molecular dynamics simulation. J Mater Process Technol 192–193:607–612. https://doi.org/10.1016/j.jmatprotec.2007.04.028
Zong WJ, Sun T, Li D, Cheng K, Liang YC (2008) XPS analysis of the groove wearing marks on flank face of diamond tool in nanometric cutting of silicon wafer. Int J Mach Tools Manuf 48(15):1678–1687. https://doi.org/10.1016/j.ijmachtools.2008.06.008
Yan J, Oowada T, Zhou T, Kuriyagawa T (2009) Precision machining of microstructures on electroless-plated NiP surface for molding glass components. J Mater Process Technol 209(10):4802–4808. https://doi.org/10.1016/j.jmatprotec.2008.12.008
Tong Z, Liang YC, Yang XC, Luo XC (2014) Investigation on the thermal effects during nanometric cutting process while using nanoscale diamond tools. Int J Adv Manuf Technol 74(9–12):1709–1718. https://doi.org/10.1007/s00170-014-6087-x
Woon K, Rahman M (2010) The effect of tool edge radius on the chip formation behavior of tool-based micromachining. Int J Adv Manuf Technol 50(9–12):961–977. https://doi.org/10.1007/s00170-010-2574-x
Fang FZ, Wu H, Zhou W, Hu XT (2007) A study on mechanism of nano-cutting single crystal silicon. J Mater Process Technol. https://doi.org/10.1016/j.jmatprotec.2006.12.007
Woon KS, Rahman M (2010) Extrusion-like chip formation mechanism and its role in suppressing void nucleation. CIRP Ann Manuf Technol 59(1):129–132. https://doi.org/10.1016/j.cirp.2010.03.094
Kim C-J, Bono M, Ni J (2002) Experimental analysis of chip formation in micro-milling. Technical papers-society of manufacturing engineers-all series
Ikawa N, Shimada S, Tanaka H (1992) Minimum thickness of cut in micromachining. Nanotechnology 3(1):6
Yuan ZJ, Zhou M, Dong S (1996) Effect of diamond tool sharpness on minimum cutting thickness and cutting surface integrity in ultraprecision machining. J Mater Process Technol 62(4):327–330. https://doi.org/10.1016/S0924-0136(96)02429-6
Malekian M, Mostofa MG, Park SS, Jun MBG (2012) Modeling of minimum uncut chip thickness in micro machining of aluminum. J Mater Process Technol 212(3):553–559. https://doi.org/10.1016/j.jmatprotec.2011.05.022
Liu ZQ, Shi ZY, Wan Y (2013) Definition and determination of the minimum uncut chip thickness of microcutting. Int J Adv Manuf Technol 69(5–8):1219–1232. https://doi.org/10.1007/s00170-013-5109-4
Lai M, Zhang XD, Fang FZ (2012) Study on critical rake angle in nanometric cutting. Appl Phys A 108(4):809–818. https://doi.org/10.1007/s00339-012-6973-8
Son SM, Lim HS, Ahn JH (2005) Effects of the friction coefficient on the minimum cutting thickness in micro cutting. Int J Mach Tools Manuf 45(4–5):529–535. https://doi.org/10.1016/j.ijmachtools.2004.09.001
Son S, Lim H, Ahn J (2006) The effect of vibration cutting on minimum cutting thickness. Int J Mach Tools Manuf 46(15):2066–2072. https://doi.org/10.1016/j.ijmachtools.2005.12.011
Lai X, Li H, Li C, Lin Z, Ni J (2008) Modelling and analysis of micro scale milling considering size effect, micro cutter edge radius and minimum chip thickness. Int J Mach Tools Manuf 48(1):1–14. https://doi.org/10.1016/j.ijmachtools.2007.08.011
Woon KS, Rahman M, Neo KS, Liu K (2008) The effect of tool edge radius on the contact phenomenon of tool-based micromachining. Int J Mach Tools Manuf 48(12–13):1395–1407. https://doi.org/10.1016/j.ijmachtools.2008.05.001
Jin X, Altintas Y (2011) Slip-line field model of micro-cutting process with round tool edge effect. J Mater Process Technol 211(3):339–355. https://doi.org/10.1016/j.jmatprotec.2010.10.006
Wang HX, Dong XY, Dong S (2002) Generation of surface micro-topography in diamond turning. J Harbin Inst Technol 34(4):509–517
Bassett E (2013) Belastungsspezifische Auslegung und Herstellung von Schneidkanten für Drehwerkzeuge. PZH Produktionstechnisches Zentrum, Garbsen
Ohbuchi Y, Obikawa T (2003) Finite element modeling of chip formation in the domain of negative rake angle cutting. J Eng Mater Technol 125(3):324–332. https://doi.org/10.1115/1.1590999
Kountanya RK A high-magnification experimental study of orthogonal cutting with edge-honed tools. In: ASME proceedings of the ASME manufacturing engineering division MED-Vol. 12, 2001 ASME international mechanical engineering congress and exposition, NY, 2001. Citeseer
Chen L, El-Wardany TI, Nasr M, Elbestawi MA (2006) Effects of edge preparation and feed when hard turning a hot work die steel with polycrystalline cubic boron nitride tools. CIRP Ann Manuf Technol 55(1):89–92. https://doi.org/10.1016/S0007-8506(07)60373-4
Tönshoff HK, Arendt C, Amor RB (2000) Cutting of hardened steel. CIRP Ann Manuf Technol 49(2):547–566. https://doi.org/10.1016/S0007-8506(07)63455-6
Ng E-G (2001) Modelling of the cutting process when machining hardened steel with polycrystalline cubic boron nitride (PCBN) tooling. The University of Birmingham, Birmingham
Nasr MNA, Ng EG, Elbestawi MA (2007) Modelling the effects of tool-edge radius on residual stresses when orthogonal cutting AISI 316L. Int J Mach Tools Manuf 47(2):401–411. https://doi.org/10.1016/j.ijmachtools.2006.03.004
Kountanya RK (2002) Process mechanics of metal cutting with edge radiused and worn tools. University of Michigan, Michigan
Kim C-J, Mayor R, Ni J (2012) Molecular dynamics simulations of plastic material deformation in machining with a round cutting edge. Int J Precis Eng Manuf 13(8):1303–1309. https://doi.org/10.1007/s12541-012-0173-5
Liu X, DeVor RE, Kapoor SG (2005) An analytical model for the prediction of minimum chip thickness in micromachining. J Manuf Sci Eng 128(2):474–481. https://doi.org/10.1115/1.2162905
Denkena B, Köhler J, Mengesha MS (2012) Influence of the cutting edge rounding on the chip formation process: part 1. Investigation of material flow, process forces, and cutting temperature. Prod Eng Res Devel 6(4):329–338. https://doi.org/10.1007/s11740-012-0366-x
Xu F, Fang F, Zhu Y, Zhang X (2017) Study on crystallographic orientation effect on surface generation of aluminum in nano-cutting. Nanoscale Res Lett 12(1):289. https://doi.org/10.1186/s11671-017-1990-3
Xu F, Fang F, Zhang X (2017) Side flow effect on surface generation in nano cutting. Nanoscale Res Lett 12(1):359. https://doi.org/10.1186/s11671-017-2136-3
Kümmel J, Gibmeier J, Müller E, Schneider R, Schulze V, Wanner A (2014) Detailed analysis of microstructure of intentionally formed built-up edges for improving wear behaviour in dry metal cutting process of steel. Wear 311(1–2):21–30. https://doi.org/10.1016/j.wear.2013.12.012
Kuznetsov V (1966) Metal transfer and build-up in friction and cutting. Pergamon Press, Oxford
Ozcatalbas Y (2003) Chip and built-up edge formation in the machining of in situ Al4C3–Al composite. Mater Des 24(3):215–221. https://doi.org/10.1016/S0261-3069(02)00146-2
Uhlmann E, Henze S, Brömmelhoff K (2015) Influence of the built-up edge on the stress state in the chip formation zone during orthogonal cutting of AISI1045. Proc CIRP 31:310–315. https://doi.org/10.1016/j.procir.2015.03.101
Fang N, Pai PS, Mosquea S (2009) The effect of built-up edge on the cutting vibrations in machining 2024-T351 aluminum alloy. Int J Adv Manuf Technol 49(1):63–71. https://doi.org/10.1007/s00170-009-2394-z
Gómez-Parra A, Álvarez-Alcón M, Salguero J, Batista M, Marcos M (2013) Analysis of the evolution of the built-up edge and built-up layer formation mechanisms in the dry turning of aeronautical aluminium alloys. Wear 302(1–2):1209–1218. https://doi.org/10.1016/j.wear.2012.12.001
Kümmel J, Braun D, Gibmeier J, Schneider J, Greiner C, Schulze V, Wanner A (2015) Study on micro texturing of uncoated cemented carbide cutting tools for wear improvement and built-up edge stabilisation. J Mater Process Technol 215:62–70. https://doi.org/10.1016/j.jmatprotec.2014.07.032
Tauhiduzzaman M, Veldhuis S (2014) Effect of material microstructure and tool geometry on surface generation in single point diamond turning. Precis Eng 38(3):481–491
Saurav G, Alexander S, Xichun L, Anupam A, Robert LR (2013) Anisotropy of single-crystal 3C–SiC during nanometric cutting. Modell Simul Mater Sci Eng 21(6):065004
Zong WJ, Li ZQ, Zhang L, Liang YC, Sun T, An CH, Zhang JF, Zhou L, Wang J (2013) Finite element simulation of diamond tool geometries affecting the 3D surface topography in fly cutting of KDP crystals. Int J Adv Manuf Technol 68(9):1927–1936. https://doi.org/10.1007/s00170-013-4804-5
Zhao T, Zhou JM, Bushlya V, Ståhl JE (2017) Effect of cutting edge radius on surface roughness and tool wear in hard turning of AISI 52100 steel. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-017-0065-z
Yue X, Xu M, Du W, Chu C (2017) Effect of cutting edge radius on surface roughness in diamond tool turning of transparent MgAl2O4 spinel ceramic. Opt Mater. https://doi.org/10.1016/j.optmat.2016.04.017
Kishawy HA, Elbestawi MA (1999) Effects of process parameters on material side flow during hard turning. Int J Mach Tool Manuf. https://doi.org/10.1016/s0890-6955(98)00084-4
Wu X, Li L, Zhao M, He N (2015) Experimental investigation of specific cutting energy and surface quality based on negative effective rake angle in micro turning. Int J Adv Manuf Technol 82(9):1941–1947. https://doi.org/10.1007/s00170-015-7548-6
Childs THC, Dornfeld D, Lee DE, Min S, Sekiya K, Tezuka R, Yamane Y (2008) The influence of cutting edge sharpness on surface finish in facing with round nosed cutting tools. CIRP J Manufact Sci Technol 1(2):70–75. https://doi.org/10.1016/j.cirpj.2008.09.001
Childs THC, Sekiya K, Tezuka R, Yamane Y, Dornfeld D, Lee DE, Min S, Wright PK (2008) Surface finishes from turning and facing with round nosed tools. CIRP Ann Manuf Technol 57(1):89–92. https://doi.org/10.1016/j.cirp.2008.03.121
Zong WJ, Huang YH, Zhang YL, Sun T (2014) Conservation law of surface roughness in single point diamond turning. Int J Mach Tools Manuf 84:58–63. https://doi.org/10.1016/j.ijmachtools.2014.04.006
Cheung CF, Lee WB (2000) A multi-spectrum analysis of surface roughness formation in ultra-precision machining. Precis Eng 24(1):77–87. https://doi.org/10.1016/S0141-6359(99)00033-1
Sata T, Li M, Takata S, Hiraoka H, Li CQ, Xing XZ, Xiao XG (1985) Analysis of surface roughness generation in turning operation and its applications. CIRP Ann Manuf Technol 34(1):473–476. https://doi.org/10.1016/S0007-8506(07)61814-9
Kong MC, Lee WB, Cheung CF, To S (2006) A study of materials swelling and recovery in single-point diamond turning of ductile materials. J Mater Process Technol 180(1–3):210–215. https://doi.org/10.1016/j.jmatprotec.2006.06.006
Schaal N, Kuster F, Wegener K (2015) Springback in metal cutting with high cutting speeds. Proc CIRP 31:24–28
Grzesik W (1996) A revised model for predicting surface roughness in turning. Wear 194(1):143–148. https://doi.org/10.1016/0043-1648(95)06825-2
He C, Zong W, Sun T (2016) Origins for the size effect of surface roughness in diamond turning. Int J Mach Tools Manuf 106:22–42
Pekelharing A, Gieszen C (1971) Material side flow in finish turning. Ann CIRP 20(1):21–22
Liu K, Melkote SN (2006) Effect of plastic side flow on surface roughness in micro-turning process. Int J Mach Tools Manuf 46(14):1778–1785. https://doi.org/10.1016/j.ijmachtools.2005.11.014
Kishawy H, Haglund A, Balazinski M (2006) Modelling of material side flow in hard turning. CIRP Ann Manuf Technol 55(1):85–88
Cheung CF, Lee WB (2000) A theoretical and experimental investigation of surface roughness formation in ultra-precision diamond turning. Int J Mach Tools Manuf 40(7):979–1002. https://doi.org/10.1016/S0890-6955(99)00103-0
Yingfei G, Jiuhua X, Hui Y (2010) Diamond tools wear and their applicability when ultra-precision turning of SiCp/2009Al matrix composite. Wear 269(11–12):699–708. https://doi.org/10.1016/j.wear.2009.09.002
Lai M, Zhang X, Fang F, Bi M (2017) Fundamental investigation on partially overlapped nano-cutting of monocrystalline germanium. Precis Eng 49:160–168. https://doi.org/10.1016/j.precisioneng.2017.02.004
He CL, Zong WJ, Cao ZM, Sun T (2015) Theoretical and empirical coupled modeling on the surface roughness in diamond turning. Mater Des 82:216–222. https://doi.org/10.1016/j.matdes.2015.05.058
Zhang SJ, To S, Wang SJ, Zhu ZW (2015) A review of surface roughness generation in ultra-precision machining. Int J Mach Tools Manuf 91:76–95. https://doi.org/10.1016/j.ijmachtools.2015.02.001
Wu X, Li L, He N (2017) Investigation on the burr formation mechanism in micro cutting. Precis Eng 47:191–196. https://doi.org/10.1016/j.precisioneng.2016.08.004
Wu X, Li L, He N, Zhao M, Zhan Z (2015) Investigation on the influence of material microstructure on cutting force and bur formation in the micro cutting of copper. Int J Adv Manuf Technol 79(1–4):321–327. https://doi.org/10.1007/s00170-015-6828-5
Fang FZ, Liu YC (2004) On minimum exit-burr in micro cutting. J Micromech Microeng 14(7):984
Lai M, Zhang X, Fang F (2017) Crystal orientation effect on the subsurface deformation of monocrystalline germanium in nanometric cutting. Nanoscale Res Lett 12(1):296. https://doi.org/10.1186/s11671-017-2047-3
Shi J, Wang Y, Yang X (2013) Nano-scale machining of polycrystalline coppers—effects of grain size and machining parameters. Nanoscale Res Lett 8(1):500. https://doi.org/10.1186/1556-276x-8-500
Simoneau A, Ng E, Elbestawi MA (2006) Surface defects during microcutting. Int J Mach Tools Manuf 46(12–13):1378–1387. https://doi.org/10.1016/j.ijmachtools.2005.10.001
Nishiguchi T, Maeda Y, Masuda M, Sawa M, Uehara K (1988) Mechanism of micro chip formation in diamond turning of Al-Mg alloy. CIRP Ann Manuf Technol 37(1):117–120. https://doi.org/10.1016/S0007-8506(07)61599-6
Li J, Fang Q, Liu B, Liu Y (2016) The effects of pore and second-phase particle on the mechanical properties of machining copper matrix from molecular dynamic simulation. Appl Surf Sci 384:419–431. https://doi.org/10.1016/j.apsusc.2016.05.051
Ding X, Butler DL, Lim GC, Cheng CK, Shaw KC, Liu K, Fong WS, Zheng HY (2009) Machining with micro-size single crystalline diamond tools fabricated by a focused ion beam. J Micromech Microeng 19(2):025005
Ding X, Lee L, Butler D, Cheng C (2009) The effects of hard particles on the surface quality when micro-cutting aluminum 6061 T6. J Micromech Microeng 19(11):115013
Yuan ZJ, Lee WB, Yao YX, Zhou M (1994) Effect of crystallographic orientation on cutting forces and surface quality in diamond cutting of single crystal. CIRP Ann Manuf Technol 43(1):39–42. https://doi.org/10.1016/S0007-8506(07)62159-3
Furukawa Y, Moronuki N (1988) Effect of material properties on ultra precise cutting processes. CIRP Ann. https://doi.org/10.1016/s0007-8506(07)61598-4
Volkert CA, Lilleodden ET (2006) Size effects in the deformation of sub-micron Au columns. Phil Mag 86(33–35):5567–5579. https://doi.org/10.1080/14786430600567739
Lee S-W, Han SM, Nix WD (2009) Uniaxial compression of fcc Au nanopillars on an MgO substrate: the effects of prestraining and annealing. Acta Mater 57(15):4404–4415. https://doi.org/10.1016/j.actamat.2009.06.002
Kim J-Y, Jang D, Greer JR (2009) Insight into the deformation behavior of niobium single crystals under uniaxial compression and tension at the nanoscale. Scr Mater 61(3):300–303. https://doi.org/10.1016/j.scriptamat.2009.04.012
Hufnagel TC, Schuh CA, Falk ML (2016) Deformation of metallic glasses: recent developments in theory, simulations, and experiments. Acta Mater 109:375–393. https://doi.org/10.1016/j.actamat.2016.01.049
Volkert CA, Donohue A, Spaepen F (2008) Effect of sample size on deformation in amorphous metals. J Appl Phys 103(8):083539. https://doi.org/10.1063/1.2884584
Torrents Abad O, Wheeler JM, Michler J, Schneider AS, Arzt E (2016) Temperature-dependent size effects on the strength of Ta and W micropillars. Acta Mater 103:483–494. https://doi.org/10.1016/j.actamat.2015.10.016
Kaira CS, Singh SS, Kirubanandham A, Chawla N (2016) Microscale deformation behavior of bicrystal boundaries in pure tin (Sn) using micropillar compression. Acta Mater 120:56–67. https://doi.org/10.1016/j.actamat.2016.08.030
Shan ZW, Mishra RK, Syed Asif SA, Warren OL, Minor AM (2008) Mechanical annealing and source-limited deformation in submicrometre-diameter Ni crystals. Nat Mater 7 (2):115–119. http://www.nature.com/nmat/journal/v7/n2/suppinfo/nmat2085_S1.html
Vollertsen F, Biermann D, Hansen HN, Jawahir IS, Kuzman K (2009) Size effects in manufacturing of metallic components. CIRP Ann Manuf Technol 58(2):566–587. https://doi.org/10.1016/j.cirp.2009.09.002
Lai M, Zhang XD, Fang FZ, Wang YF, Feng M, Tian WH (2013) Study on nanometric cutting of germanium by molecular dynamics simulation. Nanoscale Res Lett 8(1):1–10. https://doi.org/10.1186/1556-276x-8-13
Ding X, Jarfors AEW, Lim GC, Shaw KC, Liu YC, Tang LJ (2012) A study of the cutting performance of poly-crystalline oxygen free copper with single crystalline diamond micro-tools. Precis Eng. https://doi.org/10.1016/j.precisioneng.2011.09.001
Lee WB, To S, Cheung CF (2000) Effect of crystallographic orientation in diamond turning of copper single crystals. Scr Mater 42(10):937–945. https://doi.org/10.1016/S1359-6462(00)00329-8
To S, Lee WB, Chan CY (1997) Ultraprecision diamond turning of aluminium single crystals. J Mater Process Technol. https://doi.org/10.1016/s0924-0136(96)02617-9
Lawson BL, Kota N, Ozdoganlar OB (2008) Effects of crystallographic anistropy on orthogonal micromachining of single-crystal aluminum. J Manuf Sci Eng 130(3):031116. https://doi.org/10.1115/1.2917268
Zhu P, Fang F (2016) Study of the minimum depth of material removal in nanoscale mechanical machining of single crystalline copper. Comput Mater Sci 118:192–202. https://doi.org/10.1016/j.commatsci.2016.03.023
Wang Z, Chen J, Wang G, Bai Q, Liang Y (2017) Anisotropy of single-crystal silicon in nanometric cutting. Nanoscale Res Lett 12(1):300. https://doi.org/10.1186/s11671-017-2046-4
Li Z, Zhang X (2017) Subsurface deformation of germanium in ultra-precision cutting: characterization of micro-Raman spectroscopy. Int J Adv Manuf Technol 91(1):213–225. https://doi.org/10.1007/s00170-016-9749-z
Yan JW, Asami T, Harada H, Kuriyagawa T (2009) Fundamental investigation of subsurface damage in single crystalline silicon caused by diamond machining. Precis Eng. https://doi.org/10.1016/j.precisioneng.2008.10.008
Yan J, Asami T, Harada H, Kuriyagawa T (2012) Crystallographic effect on subsurface damage formation in silicon microcutting. CIRP Ann Manuf Technol 61(1):131–134. https://doi.org/10.1016/j.cirp.2012.03.070
Wang S, An C, Zhang F, Wang J, Lei X, Zhang J (2016) An experimental and theoretical investigation on the brittle ductile transition and cutting force anisotropy in cutting KDP crystal. Int J Mach Tools Manuf 106:98–108. https://doi.org/10.1016/j.ijmachtools.2016.04.009
Zong WJ, Cao ZM, He CL, Sun T (2015) Critical undeformed chip thickness of brittle materials in single point diamond turning. Int J Adv Manuf Technol 81(5–8):975–984. https://doi.org/10.1007/s00170-015-7264-2
Cai MB, Li XP, Rahman M, Tay AAO (2007) Crack initiation in relation to the tool edge radius and cutting conditions in nanoscale cutting of silicon. Int J Mach Tools Manuf 47(3–4):562–569. https://doi.org/10.1016/j.ijmachtools.2006.05.006
Li Z, Fang F, Chen J, Zhang X (2017) Machining approach of freeform optics on infrared materials via ultra-precision turning. Opt Express 25(3):2051–2062. https://doi.org/10.1364/oe.25.002051
Mukaida M, Yan J (2017) Ductile machining of single-crystal silicon for microlens arrays by ultraprecision diamond turning using a slow tool servo. Int J Mach Tools Manuf 115:2–14. https://doi.org/10.1016/j.ijmachtools.2016.11.004
Suzuki N, Masuda S, Haritani M, Shamoto E (2004) Ultraprecision micromachining of brittle materials by applying ultrasonic elliptical vibration cutting. In: Micro-nanomechatronics and human science, 2004 and the fourth symposium micro-nanomechatronics for information-based society, 2004, pp 133–138. https://doi.org/10.1109/mhs.2004.1421290
Chryssolouris G, Anifantis N, Karagiannis S (1997) Laser assisted machining: an overview. J Manuf Sci Eng 119(4B):766–769. https://doi.org/10.1115/1.2836822
Mohammadi H, Ravindra D, Kode SK, Patten JA (2015) Experimental work on micro laser-assisted diamond turning of silicon (111). J Manuf Process 19:125–128. https://doi.org/10.1016/j.jmapro.2015.06.007
Mohammadi H, Patten JA (2017) Effect of thermal softening on anisotropy and ductile mode cutting of sapphire using micro-laser assisted machining. J Micro Nano-Manuf 5(1):011007. https://doi.org/10.1115/1.4035397
Fang FZ, Chen YH, Zhang XD, Hu XT, Zhang GX (2011) Nanometric cutting of single crystal silicon surfaces modified by ion implantation. CIRP Ann Manuf Technol 60(1):527–530. https://doi.org/10.1016/j.cirp.2011.03.057
Tanaka H, Shimada S (2013) Damage-free machining of monocrystalline silicon carbide. CIRP Ann Manuf Technol 62(1):55–58. https://doi.org/10.1016/j.cirp.2013.03.098
Wang J, Fang F, Zhang X (2015) An experimental study of cutting performance on monocrystalline germanium after ion implantation. Precis Eng 39:220–223. https://doi.org/10.1016/j.precisioneng.2014.09.005
Zhang XQ, Liu K, Kumar AS, Rahman M (2014) A study of the diamond tool wear suppression mechanism in vibration-assisted machining of steel. J Mater Process Technol 214(2):496–506. https://doi.org/10.1016/j.jmatprotec.2013.10.002
Wang Y, Suzuki N, Shamoto E, Zhao Q (2011) Investigation of tool wear suppression in ultraprecision diamond machining of die steel. Precis Eng 35(4):677–685. https://doi.org/10.1016/j.precisioneng.2011.05.003
Huang S, Liu X, Chen FZ, Zheng HX, Yang XL, Wu LB, Song JL, Xu WJ (2015) Diamond-cutting ferrous metals assisted by cold plasma and ultrasonic elliptical vibration. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-015-7912-6
Nath C, Rahman M, Neo KS (2009) Machinability study of tungsten carbide using PCD tools under ultrasonic elliptical vibration cutting. Int J Mach Tools Manuf 49(14):1089–1095. https://doi.org/10.1016/j.ijmachtools.2009.07.006
Mishra S, Yadava V (2015) Laser beam micromachining (LBMM)—a review. Opt Lasers Eng 73:89–122. https://doi.org/10.1016/j.optlaseng.2015.03.017
Arnold JB, Morris TO, Sladky RE, Steger PJ (1977) Machinability studies of infrared window materials and metals. Opt Eng 16(4):164324. https://doi.org/10.1117/12.7972049
Brinksmeier E, Glaebe R, Osmer J (2011) Surface integrity demands of high precision optical molds and realization by a new process chain. Proc Eng 19:40–43. https://doi.org/10.1016/j.proeng.2011.11.077
Wang J, Fang F, Zhang X (2017) Nanometric cutting of silicon with an amorphous-crystalline layered structure: a molecular dynamics study. Nanoscale Res Lett 12(1):41. https://doi.org/10.1186/s11671-017-1829-y
Ding X, Rahman M (2012) A study of the performance of cutting polycrystalline Al 6061 T6 with single crystalline diamond micro-tools. Precis Eng 36(4):593–603. https://doi.org/10.1016/j.precisioneng.2012.04.009
Xu FF, Fang FZ, Zhang XD (2017) Hard particle effect on surface generation in nano-cutting. Appl Surf Sci 425:1020–1027. https://doi.org/10.1016/j.apsusc.2017.07.089
Ge YF, Xu JH, Yang H, Luo SB, Fu YC (2008) Workpiece surface quality when ultra-precision turning of SiCp/Al composites. J Mater Process Technol 203(1–3):166–175. https://doi.org/10.1016/j.jmatprotec.2007.09.070
Wang SJ, Chen X, To S, Ouyang XB, Liu Q, Liu JW, Lee WB (2015) Effect of cutting parameters on heat generation in ultra-precision milling of aluminum alloy 6061. Int J Adv Manuf Technol 80(5–8):1265–1275. https://doi.org/10.1007/s00170-015-7072-8
Fang FZ (2015) Suggestions of strategic development of manufactuirng: “Manufacturing 3.0”. People’s Daily, Beijing (in Chinese)
Acknowledgements
The authors thank the supports of Science Challenge Project (No. TZ2018006), the National Natural Science Foundation (Nos. 61635008 & 51320105009), the National Key Research and Development Program (No. 2016YFB1102200), the ‘111’ project by the State Administration of Foreign Experts Affairs and the Ministry of Education of China (No. B07014), and the Science Fondation Ireland (SFI) (No. 15/RP/B3208).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Fang, F., Xu, F. Recent Advances in Micro/Nano-cutting: Effect of Tool Edge and Material Properties. Nanomanuf Metrol 1, 4–31 (2018). https://doi.org/10.1007/s41871-018-0005-z
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s41871-018-0005-z