Abstract
In road base construction, substituting conventional mineral aggregates partially with waste tyre is envisaged to reduce the consumption of natural aggregate and to provide a sustainable way to dispose of waste tyres. This study explored the feasibility of deploying unbound crushed stone and shredded waste tyre mix for road base construction for low traffic volume roads in Sri Lanka through standard laboratory tests. The results revealed that, with the increase in shredded waste tyre (size 0.6 to 6.3 mm) content up to 8%, impact and static force resistance of the mix improved, whereas compaction characteristics worsened. As per Sri Lankan standards for pavement design, to retain sufficient compaction characteristics, 2% waste tyre substitution was feasible. Cost analysis revealed that a reduction of almost 10% of the conventional construction cost resulted in 2% shredded waste tyre substitution, and subsequent increase in waste tyre content showed only 1.6% cost reduction. Considering strength and cost contexts, this study recommends crushed stone partially substituted with 2% shredded waste tyre by weight for low traffic volume roads in Sri Lanka. The proposed method yields monetary savings of 1.142 million SLR (5630 USD) per km.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
As per The Ministry of Transport, Sri Lanka, vehicle population in the country has crossed 8 million in 2019, thereby the generation of waste tyres has escalated in the recent years [1]. The amount of waste tyres produced (in tonnes) in the United States of America, Norway, Italy and Thailand are 2.86 million, 32,000, 400,000 and 320,000, respectively [2,3,4,5]. Similarly, in Sri Lanka, if each vehicle needs changing tyres in every three to four years, the lowest possible amount of waste tyres generated per annum will be approximately 40,000 tonnes from all vehicle types [5]. Waste tyres are non-biodegradable and bulky and are difficult to dispose of in small islands like Sri Lanka. Disposal of waste tyres not only consumes money but also burdens environment.
In general, waste tyres are disposed of through landfills, incineration and pyrolysis, each one having its own advantages and disadvantages [6]. Landfills are the easiest way to scrap wastes, but unsuitable as they require large space to dispose, as waste tyres can become the breeding grounds for insects in tropical climates like Sri Lanka and as waste tyres may be prone to substantial fire risk due to high energy content [6]. To overcome pertaining issues in landfills, waste tyres could be incinerated; however, it releases harmful gases such as SO2, H2S, HCl and HCN to the air [4], and thus strongly discouraged by environmentalists. Pyrolysis, a relatively better option among these to dispose of waste tyres, is an endothermic process where waste tyre is decomposed chemically in an oxygen-free environment at elevated temperatures to produce pyro-oil [4, 6]. Though pyrolysis produces less amount of toxic gases, the applications of it are limited worldwide [4]. In order to enable deploying waste tyres in a greater variety of applications, Central Environmental Authority (CEA) of Sri Lanka has classified waste tyres into three categories and defined respective applications: partly worn tyres, retreaded tyres and end-of-life tyres [6]. Accordingly, CEA recommends the usage of end-of-life tyres in civil engineering applications such as construction, coastal protection, irrigation and habitat for sea life [6].
In a variety of civil engineering applications, deploying waste materials such as construction and demolition waste, tyre, coffee waste, plastic, ceramic, recycled olive core as partial replacements for coarse aggregates, fine particles and cementitious material, have gained considerable attention in the recent past [7,8,9,10,11,12,13]. Noticeably, waste tyres have been reportedly deployed in various construction projects due to their abundant quantity, economic affordability and complex-free processing [5, 14,15,16]. Using waste tyres as partial substitute for conventional construction materials not only helps to overcome material scarcity but also contributes to reduce environmental impact due to overexploitation of natural mineral deposits. In Sri Lanka, heightened law enforcement by authorities to prevent extraction of natural deposits has led to inadequate supply of mineral aggregates for road construction projects [17, 18]. Mineral aggregate is a vital material used in road construction that typically accounts for more than 90% by weight of the asphalt mixes [19]. Using waste tyres appropriately in place of natural mineral aggregate for road construction is envisaged to be a viable solution that has been already practiced in some parts of the globe, however, remains unexplored in Sri Lankan context [15, 16, 20]. From industry perspectives, the application of aggregate and waste tyre mix in road construction yields two benefits: one is promoting industry involvement in sustainable construction practices and second is paving innovative way for non-biodegradable waste disposal.
ASTM D6270 [21] stipulates guidelines for standard civil engineering applications of scraped tyres of the following forms: granulated rubber (below 425 μm to 12 mm), ground rubber (below 425 μm to 2 mm), powdered rubber (below 425 μm), rough shred (between 50 × 50 × 50 mm and 762 × 50 × 100 mm), tyre chips (12 to 50 mm) and tyre shreds (50 to 305 mm). Ground and powdered rubber are of large surface areas, which are preferred in bitumen modification, whereas granulated rubber is suitable for hot mix asphalt applications [2, 22]. The usage of tyre shreds and chips has been reported in embankment construction [2]. Xiao et al. [23] have showed that presence of crumb rubber improved Voids in Mineral Aggregate (VMA) in superpave mix design. Low-strength soil stabilized by cement and partially substituted with tyre chips has been recommended for low-cost and environmental friendly embankment construction in Thailand [5]. Signes et al. [15] have conducted a comprehensive study on replacing sub-ballast material with scrapped tyre and concluded that partial replacement up to 5% was feasible owing to bearing ability of the mix.
Heitzman [22] has indicated that deploying waste tyres in civil engineering applications was subjected to two major issues: One was defining standards for testing of the new technology and regulations pertaining to environment and the other one was adaptability of new technology by industries for large scale applications. Findings of the study by Eldin and Senouci [24] have highlighted that deploying waste tyre in road construction did not require significant additional effort, however, the compressibility issues due to the presence of rubber to be attended carefully. At initial stage, standard laboratory tests could be helpful to assess the application potential of mixes substituted with waste tyre in structural stability and cost contexts, which could be further extended or tuned to suit industrial applications [22, 25]. Researchers have conducted a series of laboratory experiments including density, flakiness index, water absorption, compaction, California Bearing Ratio (CBR), Aggregate Crushing Value (ACV), Aggregate Impact Value (AIV), Ten percent Fines Value (TFV), Los Angeles Abrasion Value (LAAV), cyclic load triaxial on conventional materials substituted with different types of wastes to obtain basic geotechnical, mechanical and thermal properties of alternative construction materials [26,27,28,29,30,31]. From environmental perspectives, non-biodegradable synthetic fiber in waste tyres is a major issue as long as its application is concerned. Petkovic et al. [3] proposed a framework to assess environmental impact from the use of recycled materials including shredded tyres in road construction in Norway. The proposed framework first characterized the given recycled material under specified conditions followed up by the corresponding risk assessment. A study by Sheehan et al. [32] showed that leachates collected from tyre shreds installed above the water table caused no adverse effects but saturated condition would result in highly localized toxic materials in water bodies. Another study by Eldin and Senouci [24] reported little or no influence from leachate formed from tyre shreds on groundwater.
Sri Lanka, a tropical island nation located in the Indian ocean, provides majority of the transport services through a well-connected road network, which comprises 12,500 km long national highways (15%) and provincial or local roads with low traffic volume (85%) [18, 33]. Since the major fraction of the roads is of low traffic volume, deploying cost-effective materials with sufficient structural stability for construction would immensely contribute in saving money. Using a new combination of materials in road construction is a complex process, which requires a comprehensive understanding of the behavior of the mixture and its compliance against design and construction standards. Current practices on pavement design and construction in Sri Lanka are governed by Sri Lankan Standards (SLS) for roads and Overseas Road Note 31 Standard (ORN 31), which are empirical and are based on parameters including subgrade strength (in terms of CBR) and traffic loading (in terms of axle loading) [34, 35]. This originated the presented study: crushed stone partially substituted with shredded waste tyres for the construction of low-volume road bases in Sri Lanka.
Research objective and scope
The presented work aimed to evaluate the feasibility of using unbound crushed stones partially substituted with shredded waste tyre in road bases. The objective of this study was to assess whether the mechanical properties of crushed stone and shredded waste tyre mixes fulfill the requirements for road bases established in SLS and ORN31 standards [34, 35]. Eventually, the waste tyre percentage that yielded satisfactory mechanical characteristics and with minimum total production cost was chosen. It should be understood that resilient modulus and permanent deformation are the most accurate and reliable parameters to evaluate the performance of unbound road bases [31, 36]. Currently, pavement design in Sri Lanka, however, follows empirical method based on CBR. This study, therefore, proposed a simple evaluation method to assess the performance of unbound crushed stone road base partially substituted with shredded waste tyre based on laboratory tests including compaction, CBR, AIV, TFV and LAAV.
The proposed assessment framework is complex-free and inexpensive to evaluate construction materials for road bases of low-volume roads. To the best of author’s knowledge, using waste tyres for road bases remains unexplored in Sri Lankan context. The proposed technique has two major advantages: one is cost-effective solution to overcome material scarcity and the second is an alternative method to discard waste tyres.
Study framework
Figure 1 shows the detailed framework of this study. The study was conducted in three stages. At stage I, individual materials (crushed stone and shredded waste tyre) were characterized using standard laboratory tests to verify whether they were free from anomalies and were in compliance with standard requirements. Stage II consisted of standard laboratory tests on various compositions of crushed stone and shredded waste tyre mix to evaluate their resistance to compaction, impact, static and abrasion loadings. Also, the obtained parameters were checked against respective standard requirements. Production costs of alternative mix compositions were first computed in Stage III, and finally appropriate composition of crushed stone and shredded waste tyre mix with the lowest production cost that satisfied minimum strength requirements was chosen.
Materials and method
Material characterization
Dense graded crushed stone with particle size distribution shown in Fig. 2 was chosen for modification with waste tyre in this study. The selected composition was in accordance with standard requirement for aggregates with nominal maximum size of 20 mm for road bases as stipulated in ORN31 and SLS for roads [34, 35]. Crushed stone of different sizes as shown in Fig. 2a was first sieved separately and blended together in required proportions to obtain the required gradation (Fig. 2b).
Waste tyre chosen to be added to crushed stone was of motorcycle considering its local availability and simplicity in shredding. As per The Ministry of Transport, Sri Lanka, number of motorcycles in 2019 was 4.67 million, which was over 58% of the total number of vehicles [1]. Sri Lankan population commonly uses motorcycles for all kinds of commuting, which increases the chances of generating relatively higher share of motorcycle waste tyres. To capitalize on this, the study has been initiated with waste motorcycle tyres.
Waste tyre was first cleaned with water to remove impurities and dried in air. The steel belt reinforcement in the tyre was then removed manually with an angle grinder. After removing steel belt of 0.4 kg, the available amount of tyre for shredding was 2.4 kg, which was fed into shredder machine and sliced into crumbs. The shredder machine with power rating 15 kW, three phase, was operated for 40 s to produce tyre crumbs shown in Fig. 2c. Particle size distribution of crumbed waste tyre obtained from shredder machine is depicted in Fig. 2d. Grain size of prepared waste tyre crumb ranged from 0.6 to 6.3 mm, which belongs to the category of granulated rubber as per ASTM D6270 [21].
Initially, physical properties of crushed stone and shredded waste tyre were determined separately using standard laboratory tests [37,38,39], and are summarized in Table 1. The properties were found to be in compliance with respective standard requirements of materials used for road bases [34, 35], which implied that both crushed stone and shredded waste tyre had no specific influence on other mix parameters. Density and flakiness index lied in the typical range stipulated for aggregates in standards [34, 35]. Non-plastic nature of crushed stone ensured that its swell potential remains unaffected by moisture changes [34, 35]. Low water absorption was an indication that crushed stone had very low internal pores, thereby they were free from micro-fractures.
Mix characterization
Range of mix compositions of crushed stone with waste tyres for various engineering applications is found in contemporary literature. Speir and Witczak [40] used 0–15% granulated waste tyre/chips to substitute dense-graded aggregate base course/sand-sub-base. Promputthangkoon et al. [5] substituted cement-treated low-strength soil with 0–25% tyre chips. In another study, 3–10% ground rubber of 177 microns was used to partially substitute lateritic soil [41]. Signes et al. [15] replaced 1–10% aggregates with waste tyre for the application of sub-ballast layers in their study. Study by Gamalath et al. [42] showed that compressive strength of concrete paving blocks reduced drastically with the increase in rubber content in the mix. Understanding the fact that increasing waste tyre/rubber content reduces bearing ability of mix, this study selected waste tyre substitution by weight in the range of 0 to 8%. Accordingly, mixtures of alternative compositions of crushed stone and shredded waste tyre were prepared as shown in Table 2, to examine the influence of shredded waste tyre content in the mix.
The proposed mixes in Table 2 were subjected to series of laboratory tests according to BS and ASTM standards to examine density and strength characteristics of crushed stone–shredded waste tyre mix as follows: compressibility tests including modified Proctor compaction and CBR [43], Aggregate Impact Value (AIV) to examine the resistance to impact forces [44], Ten percent Fines Value (TFV) to examine the resistance to static forces [45] and Los Angeles Abrasion Value (LAAV) to assess the abrasion resistance [46].
Initially modified Proctor compaction was conducted on pure crushed stone (0% waste tyre) to determine the Maximum Dry Density (MDD) and Optimum Moisture Content (OMC), which were 2.347 Mg/m3 and 6.2%, respectively. Subsequent CBR tests with alternative waste tyre compositions were performed using the obtained MDD and OMC. AIV and TFV tests were conducted on 10–14 mm crushed stone sample by applying impact and static loadings stipulated in standards, respectively [44, 45]. LAAV test was performed on 9.5–19 mm crushed stone sample by exerting abrasive forces. Each test was carried out on at least 5 samples to minimize the effect of random error in the measurements. The CBR and strength-related parameters obtained from laboratory experiments were screened for outliers and then averaged out to find the mean of the concerned parameter. When the tests were repeated on samples, care was taken to maintain the same compaction configuration, load application, temperature and moisture between samples.
Cost estimation
Crushed stone used for road base construction in Sri Lanka is typically quarried from open-pit mines. The costs involved in laying road base with crushed stone are defined in Highway Schedule Rates (HSR), Sri Lanka [47], and are summarized in Table 3. Aggregate cost primarily includes extraction and crushing cost, loading and unloading cost, transport cost, and laying cost at construction site.
Similarly, cost involved in the preparation of shredded waste tyre, detailed in Table 4, includes cost of waste tyre, transport cost for collection and supply of waste tyre to construction site, shredding cost and labor cost. Generally, end-of-life tyres can be obtained free of charge from automobile shops, as they want to get rid of waste tyres as much as possible considering the hassle involved in discarding them. Transport cost, electricity cost, and labor cost were assigned in accordance with present industrial rates [47, 48]. Due to the absence of precise data, the machine depreciation cost was assumed to be 1 SLR/kg of shredded waste tyre production.
In this study, a road construction site located at 150 km from a quarry in the Northern part of Sri Lanka was considered for cost estimation of road base construction with the proposed mixture of crushed stone and shredded waste tyre. CBR values of subgrade in the construction site ranged between 15 and 20, and hence subgrade was assigned to strength class S5 as per ORN 31 [35]. Anticipating low traffic volume on the selected road, traffic class T3 was chosen for the analysis. For this road, according to ORN 31 [35], minimum required thicknesses of layers for granular road base/surface dressing pavement category were determined, and are shown in Fig. 3. As per Road Development Authority (RDA) regulations, typical width for roads with low traffic volume is 5.5 m [49]. All cost estimations were made considering 1 km long stretch of the road. For the given dimensions, the compacted volume of road base made of pure crushed stone was 962.50 cu. m (175 mm × 5.5 m × 1 km), which was considered for the replacement with alternative compositions of crushed stone and shredded waste tyre.
Results and discussion
Structural feasibility
The density- and strength-related parameters of alternative mix compositions obtained from laboratory tests are detailed along with their respective minimum/maximum standard requirements in Table 5. As it can be seen from Table 5, the compaction characteristics of crushed stone and shredded waste tyre mix, such as MDD and CBR, worsened as shredded waste tyre substitution in the mix was increased. During compaction and CBR tests, waste tyres in the mix absorbed a portion of applied compaction energy and dissipated it due to their resilient nature without transferring it to crushed stone matrix effectively, which prevented crushed stone particles from being fully compacted and being packed closely. Loss of close packing of grains led to decrease in density, and hence reduction in CBR value. When waste tyre content was increased in the mix, amount of compaction energy absorbed by waste tyres also proportionally increased, which contributed to additional reduction in density. Similar trends in bulk density were observed in studies that replaced rubber in sand concrete and unbound mixes made of coarse aggregates [15, 27, 31]. Signes et al. [15] reported a drastic drop in CBR values with the increase in waste tyre content for sub-ballast layers.
On the other hand, AIV and TFV presented in Table 5 indicate that the resistance of the mix to impact and static forces improved substantially with the increase in waste tyre substitution up to 8%. Shredded waste tyre particles surrounded crushed stone and resisted a fraction of applied impact and static forces, which prevented crushed stone particles from being directly impacted. This contributed to improve AIV and TFV. Accumulation of waste tyre in the mix further contributed to this reduction in direct impact on crushed stones. Literature reported improvement in ACV with the rise in rubber content in demolition waste mixed with crumb rubber [31]. The abrasion characteristics (LAAV) remained unaffected for all mixes. It could be attributed to the smaller size of waste tyre crumb used, which might be inadequate to negate abrasive forces between crushed stone particles.
The results summarized in Table 5 indicate that MDD, AIV, TFV and LAAV of all mix compositions with waste tyre replacement from 0 to 8% fulfilled their respective requirements for road bases stipulated in SLS and ORN31 standards. From CBR perspectives, partial substitution of shredded waste tyre up to 2% by weight was feasible for the construction of road base for low traffic volume roads. Finding alternative ways to improve CBR values will permit further substitution of shredded waste tyre in the mix.
Cost feasibility
The estimated production cost of crushed stone and shredded waste tyre mix of various compositions for a predefined road base configuration (175 mm × 5.5 m × 1 km) is tabulated in Table 6. The total production cost consists of raw material cost, material processing cost, material transport cost and construction cost as defined in Tables 3 and 4. The results revealed that monetary savings increased when waste tyre substitution in the mix was increased from 2 to 8%. For 2% waste tyre substitution, 9.68% monetary savings from conventional construction cost was obtained. However, as the percentage of waste tyre substitution increased beyond 2%, only a marginal savings of 1.6% from conventional construction cost was observed in subsequent mixes. This could be attributed to the compromising effect between the reduction in crushed stone cost and increase in processing cost of shredded waste tyre. In overall, waste tyre substitution of 2–8% yielded monetary savings between 9.68 and 12.16%. It is worth mentioning that the proposed method is economically advantageous.
Figures 4 and 5 simultaneously compare the variations in density and strength parameters, and total production cost of mix against shredded waste tyre content in the mix. The minimum/maximum requirement of each parameter according to standard, also is denoted in Figs. 4 and 5 to facilitate the selection of each attribute. As pointed out earlier, density-related parameters worsened; however, strength parameters improved with the accumulation of waste tyre in the mix. It is worth adding that, the change (increase or decrease) in density and strength parameters were gradual. This gradual change could be attributed to proportionately developed cushion effect in the mix with the accumulation of waste tyre particles, which contributed to partially cease load applications on crushed stone matrix. Total production cost of mix reduced with the increase in waste tyre content, noticeably exhibiting a drastic change between 0 and 2%.
The comparison presented in Figs. 4 and 5 revealed that up to 2% shredded waste tyre substitution by weight was feasible, satisfying minimum/maximum density and strength requirements stipulated in SLS and ORN31 standards [34, 35]. Feasible waste tyre content corresponding to density and strength parameters, and total production cost, is denoted in Figs. 4 and 5. For all mix compositions, a considerable margin between laboratory test results and respective maximum standard requirements was observed for AIV, TFV and LAAV (Fig. 5). This emphasizes the fact that proposed method has potential to be extended to weak aggregate types with low impact, static and abrasive resistance to exploit the currently available margin. This extended work, however, is to be assessed for compaction behavior of mix before concluding about its application potential.
Conclusions
The application of waste material in road construction in Sri Lanka, a tropical weathered, developing nation with almost 85% low traffic volume roads, remains primitive to date. This study explored the feasibility of substituting unbound crushed stone with shredded waste tyre for road base construction in Sri Lanka and proposed a cost-effective solution through an experimental study stipulated in Overseas Road Note 31 (ORN31) and Sri Lankan Standards (SLS) for roads.
The salient conclusions drawn from the study are listed below:
-
The laboratory experiments performed in this study revealed that shredded waste tyre of size ranging from 0.6 to 6.3 mm has the potential to replace conventional crushed stone partially for road base construction.
-
Study results confirmed that, with the accumulation of shredded waste tyre substitution up to 8%, resistance of the mix against impact and static force increased, whereas the compaction characteristics deteriorated.
-
The estimated total cost of road base construction with crushed stone and shredded waste tyre mix showed a decreasing trend with the increase in shredded waste tyre substitution.
-
The total cost reduction for the mixes substituted with shredded waste tyre from 0 to 2% by weight was 9.68% of the conventional road construction cost. Thereafter, a marginal cost reduction was observed due to increase in processing cost incurred in shredding of waste tyres.
-
To be in par with the requirements stipulated in SLS and ORN31 standards, eventually, the waste tyre substitution up to 2% by weight was feasible for road base construction uncompromising required compaction characteristics.
-
For 2% shredded waste substitution in the proposed mix, monetary savings of 1.142 million SLR (5630 USD) per km was obtained.
Recommendations and limitations
This research primarily focused on road base construction for low traffic volume roads in Sri Lanka. The proposed method contains two key aspects: a cost-effective material combination for local road construction industry, and a technique to dispose of non-biodegradable waste tyres. Findings of the study could be useful for developing nations with similar design practices, which suffer from budget constraints for road infrastructure development.
Considering density, strength and cost contexts, this study recommends crushed stone partially substituted with 2% shredded waste tyre by weight for road bases with low traffic volume (class T3 or below according to ORN31) in Sri Lanka. The possible monetary savings from this proposed method is 1.142 million SLR (5630 USD) per km.
The protocols and standards followed in this study are governed by Sri Lankan Standard (SLS) and Overseas Road Note 31 Standard (ORN 31), which are empirical and are based on parameters including subgrade strength (in terms of CBR) and traffic load (in terms of axle loading). It is noteworthy mentioning that current world practices emphasize the need of mechanistic design of pavements, which assess the performance of a pavement under repeated loading. Such design practices require comprehensive evaluation of additional parameters including resilient modulus and permanent deformation of pavements under repeated loading. Author of this paper, therefore, recommends that extension of this work to roads with heavy traffic volume or weak aggregate types require a thorough study on stress–strain relationship of the proposed material combination covering elastic and plastic deformations under repeated loading. By conducting cyclic triaxial tests, resilient modulus and permanent deformation could be accurately obtained.
Availability of data and materials
The datasets used and/or analyzed during the current study are available from the corresponding author on reasonable request.
References
Vehicle population. Ministry of Transport, Sri Lanka. http://www.transport.gov.lk/web/index.php?option=com_content&view=article&id=26&Itemid=146&lang=en#vehicle-population. Accessed 6 Apr 2021
User Guidelines for Waste and Byproduct Materials in Pavement Construction. Federal Highway Administration Research and Technology, FHWA-RD-97-148, 2016. [Online]. https://www.fhwa.dot.gov/publications/research/infrastructure/structures/97148/st1.cfm
Petkovic G, Engelsen CJ, Håøya A-O, Breedveld G (2004) Environmental impact from the use of recycled materials in road construction: method for decision-making in Norway. Resour Conserv Recycl 42(3):249–264. https://doi.org/10.1016/j.resconrec.2004.04.004
Sharma VK, Fortuna F, Mincarini M, Berillo M, Cornacchia G (2000) Disposal of waste tyres for energy recovery and safe environment. Appl Energy 65(1):381–394. https://doi.org/10.1016/S0306-2619(99)00085-9
Promputthangkoon P, Karnchanachetanee B (2013) Geomaterial prepared from waste tyres, soil and cement. Procedia Soc Behav Sci 91:421–428. https://doi.org/10.1016/j.sbspro.2013.08.439
Technical guidelines on used tyre management in Sri Lanka. Central Environmental Authority. http://www.cea.lk/web/images/pdf/Used-tyre-management-guidelines.pdf . Accessed 2 Sept 2020
Boukhelkhal D, Guendouz M, Bourdot A, Cheriet H, Messaoudi K (2021) Correction to: Elaboration of bio-based building materials made from recycled olive core. MRS Energy Sustain. https://doi.org/10.1557/s43581-021-00010-y
Guendouz M, Boukhelkhal D (2019) Properties of flowable sand concrete containing ceramic wastes. J Adhes Sci Technol 33(24):2661–2683. https://doi.org/10.1080/01694243.2019.1653594
Guendouz FDM, Boukendakdji O, Kadri EH, Bentchikou M, Soualhi H (2016) Use of plastic waste in sand concrete. Mater Environ Sci 7(2):382–389
Choudhary A, Jha J, Gill K (2010) Utilization of plastic wastes for improving the sub-grades in flexible pavements. In: GeoShanghai international conference 2010, pp 320–326. https://doi.org/10.1061/41104(377)39
Arulrajah A, Yaghoubi E, Wong YC, Horpibulsuk S (2017) Recycled plastic granules and demolition wastes as construction materials: resilient moduli and strength characteristics. Constr Build Mater 147:9–19
Yaghoubi E, Arulrajah A, Wong YC, Horpibulsuk S (2017) Stiffness properties of recycled concrete aggregate with polyethylene plastic granules in unbound pavement applications. J Mater Civ Eng 29(4):04016271. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001821
Mohamed G, Djamila B (2018) Properties of dune sand concrete containing coffee waste. MATEC Web Conf 149:01039. https://doi.org/10.1051/matecconf/201814901039
Humphrey D, Blumenthal M (2010) The use of tire-derived aggregate in road construction applications. In: Green streets and highways, pp 299–313
Hidalgo Signes C, Martínez Fernández P, Medel Perallón E, Insa Franco R (2015) Characterisation of an unbound granular mixture with waste tyre rubber for subballast layers. Mater Struct 48(12):3847–3861. https://doi.org/10.1617/s11527-014-0443-z
Mashaan NS, Karim MR (2014) Waste tyre rubber in asphalt pavement modification. Mater Res Innov 18(sup6):S66–S69. https://doi.org/10.1179/1432891714Z.000000000922
Economic Analysis: Northern Road Connectivity Project (2010). Road Development Authority
National Road master plan (2007). Road Development Authority, Colombo
Huang Y, Bird RN, Heidrich O (2007) A review of the use of recycled solid waste materials in asphalt pavements. Resour Conserv Recycl 52:58–73
Mashaan NS, Ali AH, Karim MR, Abdelaziz M (2014) A review on using crumb rubber in reinforcement of asphalt pavement. Sci World J 2014:214612. https://doi.org/10.1155/2014/214612
ASTM D6270, Standard Practice for Use of Scrap Tires in Civil Engineering Applications (1998). ASTM International, West Conshohocken, PA
Heitzman M (1992) Design and construction of asphalt paving materials with crumb rubber modifier. Transp Res Rec 1339:1–8
Xiao F, Amirkhanian SN, Shen J, Putman B (2009) Influences of crumb rubber size and type on reclaimed asphalt pavement (RAP) mixtures. Constr Build Mater 23(2):1028–1034. https://doi.org/10.1016/j.conbuildmat.2008.05.002
Eldin NN, Senouci AB (1992) Use of scrap tires in road construction. J Constr Eng Manag 118(3):561–576. https://doi.org/10.1061/(ASCE)0733-9364(1992)118:3(561)
Imtiaz A, Lovell CW (1992) Use of waste materials in highway construction: state of the practice and evaluation of the selected waste products. Transp Res Rec 1345:1–9
Guendouz DBM, Bourdot A, Babachikh O, Hamadouche A (2020) The effect of ceramic wastes on physical and mechanical properties of eco-friendly flowable sand concrete. Adv Ceram Mater. https://doi.org/10.5772/intechopen
Mohamed G, Djamila B (2018) Physical, mechanical and thermal properties of crushed sand concrete containing rubber waste. MATEC Web Conf 149:01076. https://doi.org/10.1051/matecconf/201814901076
Mohamed G, Djamila B (2018) Physical and mechanical properties of cement mortar made with brick waste. MATEC Web Conf 149:01077. https://doi.org/10.1051/matecconf/201814901077
Arulrajah A, Disfani MM, Horpibulsuk S, Suksiripattanapong C, Prongmanee N (2014) Physical properties and shear strength responses of recycled construction and demolition materials in unbound pavement base/subbase applications. Constr Build Mater 58:245–257
Fabiana DCL, Rosangela DSM, Kamilla LV, Liedi B (2011) Laboratory evaluation of recycled construction and demolition waste for pavements. Constr Build Mater 25:2972–2979
Saberian M, Li J, Boroujeni M, Law D, Li C-Q (2020) Application of demolition wastes mixed with crushed glass and crumb rubber in pavement base/subbase. Resour Conserv Recycl 156:104722. https://doi.org/10.1016/j.resconrec.2020.104722
Sheehan PJ, Warmerdam JM, Ogle S, Humphrey DN, Patenaude SM (2006) Evaluating the risk to aquatic ecosystems posed by leachate from tire shred fill in roads using toxicity tests, toxicity identification evaluations, and groundwater modeling. Environ Toxicol Chem 25(2):400–411. https://doi.org/10.1897/04-532R2.1
National Highways (Class A, B & E Roads). Road Development Authority, Sri Lanka. www.rda.gov.lk. Accessed 25 Mar 2021
SCA/5, Standard Specifications for Construction and Maintenance of roads and bridges (2009). Institute for Construction Training and Development (ICTAD), Sri Lanka
ORN31, A guide to the structural design of bitumen surfaced roads in tropical and sub-tropical countries (1993). Transport Research Laboratory, United Kingdom
Saberian M, Li J, Nguyen B, Wang G (2018) Permanent deformation behaviour of pavement base and subbase containing recycle concrete aggregate, coarse and fine crumb rubber. Constr Build Mater 178:51–58. https://doi.org/10.1016/j.conbuildmat.2018.05.107
BS 812-105.1, Testing aggregates—part 105, methods for determination of particle shape (1989) British Standards Institution, United Kingdom
BS 812: Part 2, testing aggregates—part 2, methods for determination of density (1995) British Standards Institution, United Kingdom
BS EN 933-1, Tests for geometrical properties of aggregates part 1: determination of particle size distribution—sieving method (2012). British Standards Institution, United Kingdom
Speir RH, Witczak MW (1996) Use of shredded rubber in unbound granular flexible pavement layers. Transp Res Rec 1547(1):96–106. https://doi.org/10.1177/0361198196154700114
Gordan B, Adnan A (2015) Strength performance based on flexibility from laterite soil using tire powder and micro silica. J Mater 2015:830903. https://doi.org/10.1155/2015/830903
Gamalath HGP, Weerasinghe TGPL, Nanayakkara SMA (2016) Use of waste rubber granules for the production of concrete paving blocks. In: The 7th international conference on sustainable built environment, Kandy, Sri Lanka
BS 1377-4, Methods of test for—soils for civil engineering purposes—part 4, compaction-related tests (1990). British Standards Institution, United Kingdom
BS 812: 112, Testing aggregates—part 112, methods for determination of aggregate impact value (1990). British Standards Institution, United Kingdom
BS 812: 111, Testing aggregates—part 111, methods for determination of ten percent fines value (1990). British Standards Institution , United Kingdom
ASTM C131 / C131M, Standard test method for resistance to degradation of small-size coarse aggregate by abrasion and impact in the Los Angeles Machine (2014). ASTM International, West Conshohocken, PA
HSR-2019, Highway schedule of rates—Northern Province (2019). Ministry of Highways & Road Development and Petroleum Resources Development, Sri Lanka
Tariff Plan. Ceylon Electricity Board. https://ceb.lk/commercial-tariff/en. Accessed 23 Mar 2021
A guide to structural design of road under Sri Lankan condition, Road Development Authority, Sri Lanka (1999). Road Development Authority, Sri Lanka
Standard specifications for transportation materials and methods of sampling and testing (2015). AASHTO, Washington, DC
Acknowledgements
The authors acknowledge the Department of Civil Engineering, University of Jaffna, Sri Lanka for providing laboratory testing facilities.
Funding
No funding obtained.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.
Rights and permissions
About this article
Cite this article
Anburuvel, A. Crushed stone partially substituted with shredded-waste tyres of motorcycles for low-volume road base construction: a feasibility study in Sri Lanka. Innov. Infrastruct. Solut. 7, 123 (2022). https://doi.org/10.1007/s41062-021-00721-8
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s41062-021-00721-8