Abstract
This study aimed to investigate an integrated system that can deal with different pharmaceutical wastewaters. Pharmaceutical wastewater was subjected to biological, chemical and advanced oxidation according to its pollutant’s nature. Wastewater with high total suspended solids (TSS 480 mg/L) was subjected to a conventional chemical treatment process utilizing different coagulants. The best results were obtained by using calcium oxide and alum added with calcium oxide where the removal efficiency of COD was 46.8% and 51%. Highly loaded pharmaceutical wastewater (COD 9700 mg/L, BOD/COD 0.16) had been subjected to Fenton oxidation, the removal of COD reached 80.4%, and the ratio of BOD/COD is enhanced to 0.6. Photocatalysis by using different nanomaterials was applied to pharmaceutical wastewater containing 10 mg/L of phenols. Phenol is completely removed by using mesoporous TiO2 after 90-min irradiation and after 120 min in the case of TiO2/P25 and TiO2/UV 100 nanocomposites, while it is removed by 40% in case of using mesoporous TiO2/Ta2O5. Effluent-treated water from previous routes was subjected to biological treatment and followed with disinfection by using UV as post-treatment. The final COD was 40, and it matches with the Egyptian practice code for water reuse in agriculture (ECP 501 in Egyptian code of practice for the use of treated municipal wastewater for agricultural purposes. The ministry of Housing Utilities and Urban Communities., n.d. No title, 2015). Results showed also using treated wastewater in irrigation of barley and bean seeds achieved germination ratio up to 71% in barely and 70% in bean compared with that irrigated with Nile water, which reached 70% and 75%, while it was about 16.6% and 30% in case of irrigation with untreated wastewater (Jeong et al. in Water (Switzerland). https://doi.org/10.3390/w8040169, 2016).
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
The treatment and reuse of industrial wastewater have been investigated to not only preserve the natural water resources from polluted effluents but also to face water scarcity in arid and remote areas. Due to rapid urbanization and sharp population growth, the development in the medical field had dramatically increased the consumption of pharmaceuticals, and the worldwide consumption of pharmaceutics was found to be about 15 g per capita/year, while it goes as much as 50–150 g in the industrialized countries (Mylapilli and Reddy 2019; World Health Organization 2006).
To increase membrane hydrophilicity and decrease membrane fouling in pharmaceutical wastewater treatment, we construct polypropylene membrane by embedding carboxylated (–COOH) and polyethylene glycol-functionalized nanodiamond. The antifouling qualities of the membrane with –COOH and polyethylene glycol-functionalized nanodiamond were superior to that of the clean polypropylene membrane in the experimental procedures (Farag et al. 2016; Eessaa et al. 2018; Shahab et al. 2021). Nanoscale-sorbent materials offer distinct properties such as high absorption, large surface area, environmentally safe manufacture and a strong affinity for organic and inorganic compounds. This study lays the groundwork for future research into many of the present nanoscale materials for the remediation of pharma industrial wastewaters (Shehata et al. 2019; Aguilar-Perez et al. 2020).
The environmentally friendly manufacture of silver nanoparticles was from waste safflower (Carthamus tinctorius L.) aqueous extract and their antibacterial activity against Staphylococcus aureus (gram-positive) and Pseudomonas fluorescens (gram-negative). From the lowest dose tested (0.9 g/mL), nanoparticles suppressed the development of both species of bacteria. The as-synthesized silver nanoparticles were homogenous and spherical, with an average diameter of 8.67 4.7 nm, as determined by TEM and validated by SEM. The unique crystallinity of silver nanoparticles was revealed by electron diffraction and TEM investigations (Rodríguez-Felix et al. 2021).
The pollution rate and amount of wastewater generated during pharmaceutical production are depending on the used raw materials, manufacturing operations, and the variety of process technologies being used in the production process. Considering the wastewater resulting from pharmaceutical manufacturing activity, it has been classified as a “red category” as this wastewater is characterized by huge volume, complex and hazardous nature (Changotra et al. 2019). There are a lot of different technologies; both conventional and advanced technologies have been applied for pharmaceutical wastewater treatment; each of them depends on the nature of the existing contaminants. Biological treatment can be used directly and efficiently in wastewater that has a high BOD/COD ratio.
On the other hand, pharmaceutical wastewater is typically toxic for both aquatic life and biological life, with high COD and low biodegradability, which makes their biological treatment difficult and inefficient (Ferrari et al. 2003; Malik et al. 2019). In general, chemical treatment can be efficiently used as pretreatment in most industrial wastewater that contains a high content of TSS (Changotra et al. 2019; Nasr et al. 2019). Consequently, in such cases advanced oxidation processes (AOPs) are most acceptable for pharmaceutical wastewater treatment, and they can enhance biodegradability as a pretreatment method (Klavarioti et al. 2009). One type of AOPs is Fenton oxidation; other types use nanocomposites. The potential use of nanomaterials for treating pharmaceutical wastewater has been explored and reviewed by many researchers (Meng-hui et al. 2019; Bagheri et al. 2016; Cincinelli et al. 2015). The biodegradability of pharmaceutical wastewater can be enhanced by using nanocomposites (Ferrari et al. 2003). Reuse of treated wastewater is no longer an option but has become inevitable, especially in countries that suffer from water shortage, and it can be reused in agriculture if it achieves limitation for irrigation reuse (Nasr et al. 2019).
This research aims to make an integrated system for the treatment of toxic non-biodegradable pharmaceutical wastewater, which has a high content of phenol. Additionally, we study the effect of using polluted and treated wastewater with a comparison of Nile water on germination ratio for bean and barely.
Materials and methods
Pharmaceutical wastewater
The examined wastewater was collected from a pharmaceutics company located on the 6th of October industrial city, west of Cairo, Egypt. The main activity of the investigated company is producing different pharmaceutics such as antibiotics, multivitamins, urology, chest, and cold medicines.
Wastewater characterization
The wastewater composite samples were collected during the operation period of the company throughout the day and working shifts. The collected wastewater samples are transported and stored at 4 °C to be analyzed according to APHA 2017.
Wastewater treatment process
According to the nature of pollutants, the wastewater was passed through three scenarios as shown in Fig. 1. The first scenario is a direct biological treatment for pharmaceutical wastewater in the case of the ratio BOD/COD ≥ 0.40 (Fawzy et al. 2018). The second scenario is using chemical coagulation followed by biological treatment in case of high TSS. The third scenario is carried out by using AOPs and nanomaterials followed by biological treatment, which is applied in case of the high content of phenol and other toxic pollutants and subsequent BOD/COD ≤ 0.40.
Biological treatment
Biological treatment was carried out by using Plexiglas column capacity of 2.5 L. The column was filled with aerated sludge containing different flora of microorganisms. The initially mixed liquor suspended solids (MLSSs) were ranged from 3 to 4 g/L, sludge volume index (SVI) 150, and volatile matter of 75%. Dissolved oxygen in column was maintained at 2–3 mg/L by using an air pump.
Chemical treatment
Treatments using coagulants include alum, ferric chloride, lime, and ferrous sulfate that are used separately and in combinations in different concentrations. A jar test unit was used to obtain the optimal doses of each coagulant; a series of coagulants at their optimal operating conditions were obtained. The coagulants were flash mixed with raw wastewater at 250 rpm for 1–2 min. followed by flocculation at 25–30 rpm; then, the formed flocks were allowed to be settled. COD and TSS were measured to indicate the efficiencies and to get the optimal coagulant with its operating conditions (El-Shamy et al. 2017a, b, 2018).
AOPs treatment
Treatment by Fenton
It was carried out by using H2O2 (250 g/L) and ferrous sulfate as catalysts. Fenton is applied in high COD and non-biodegradability. Determination of the optimum dose of ferrous sulfate and the optimum dose of H2O2 will be performed.
Preparation of mesoporous nano-TiO2
Mesoporous TiO2 is prepared via a sol–gel process in the presence of an F127 triblock copolymer as a structure-directing agent. Molar ratios Ti (OBu)4/F127/C2H5OH/HCl/CH3COOH = 1:0.02:50:2.25:3.75, and it employed to synthesize the desired mesoporous nanomaterials. Typically, 1.6 g of F127 was dissolved in 30 mL of ethanol with stirring for 60 min, and then, 2.3 ml of CH3COOH, 0.74 ml of 30% HCl and 3.5 mL of titanium butoxide (TBOT) were added to the F127 solution under magnetic stirring for 30 min (Ismail and Bahnemann 2011). The prepared mesophase is transferred into a 40% humidity chamber at 40 °C for 12 h to evaporate ethanol and form gel. The produced gel is aged at 65 °C for 24 h. Then, it will be calcined at 450 °C in the air for 4 h at a heating rate of 1 °C/min and a cooling rate of 2 °C/min to take off the F127 surfactant and to get mesoporous TiO2 (Ismail and Bahnemann 2011). To give information on the atomic packing, a high-resolution transmission electron microscopy (HRTEM) including selected area electron diffraction (SAED) was conducted at 200 kV with a JEOL JEM-2100F-UHR (Japan) field-emission instrument equipped with a Gatan GIF 2001 energy filter and a 1 k-CCD camera to obtain EEL spectra. After preparation of the mesoporous TiO2 as well as the TiO2–TaO as doped nano-oxide using the sol–gel method, it will be used to treat the collected wastewater and will be compared by utilizing the commercially TiO2-P25 and TiO2-UV100.
Effect of treated effluent on germination and plant growth
Barely and bean seeds bought from a market in Giza, Egypt, was used for germination experiments. The seeds were irrigated with raw wastewater, treated effluent, and compared with irrigation by Nile water. For Barley, 180 seeds were put equally in 15 dishes divided into three groups and then distributed randomly. For beans, 90 seeds were put equally in 15 dishes divided into three groups and then distributed randomly. Dishes were daily irrigated to keep the moisture at the required level for germination and growth. Every day, the ratio of germination to growth state is recorded using Eq. (1) (Jacob et al. 2020). A similar experimental condition from light intensity, room temperature, and humidity was considered. The used light intensity was controlled to be 12-h light/ 12-h dark throughout the experimental period of eight growing days.
Statistical analysis
The least significant difference (L.S.D) will be used to study the germination and growing of irrigated seeds. In one-way analysis of variance, null hypothesis \(H_{0} {:}\; \mu_{1} = \mu_{2} = \mu_{3}\). Since H0 is rejected, we run the LSD test seeking to identify which means caused the rejection of H0.
where N he total number of observations, k is the number of treatments and n is number of replicates which is the same for each group.
Results and discussion
Characterization of wastewater
According to the obtained results of the analysis, pharmaceutical wastewater has a large variety of its organic load, where a large variation of COD and BOD was observed (Fig. 2). This variation returns to the batch system for pharmaceutical production. Each pharmaceutical product is produced under specific operating conditions, resulting in different organic pollutants, different amounts of washing water, and finally, different concentrations of organic loads, and this is agreed with previous studies (Azizan et al. 2020). The route of the selected treatment method is essentially depending on the nature and concentration of these pollutants.
Wastewater treatment
Chemical treatment
Jar test (coagulation, flocculation, and sedimentation) was performed to find the effectiveness of each used chemical coagulant in COD removal. Raw wastewater had pH 7.5, TSS 418 mg/L, CODt, 4700 mg/L, and CODs 2900 mg/L. In this study, it was found in Table 1 that all used coagulants were efficient in CODt removal where removal efficiency was 46.8%, 48.3%, and 51% in the case of CaO, alum and CaO combined with alum, and it is also removed as a part of CODs. However, reduced COD in the case of CaO with alum was slightly more than those in separated CaO but economic cost recommends that CaO is preferable. The residual COD of about 2500 mg/L will be acceptable for the following biological processes. Using alum, ferric chloride, and ferrous sulfate to treat pharmaceutical wastewater containing COD 2800 mg/L, the percentage removal was 48.5%, 44.2%, and 32.1%, respectively (Saleem 2007).
Treatment by Fenton oxidation
The optimum dose of ferrous sulfate and H2O2 was 0.5 g/100 mL and 5 mL/100 mL, and the reaction time was 15 min, the removal of COD reached 79.7% (Fig. 3a, b) and BOD/COD increased from 0.2 to 0.55. These results are compatible with Zhang et al. (2019).
Phenol removal by nanomaterials and nano
The HRTEM and SAED images for prepared mesoporous TiO2 and other commercial nanocomposites materials are indicated in Fig. 3. All nanocomposites have a cubic crystal structure, but TiO2/UV 100 nanocomposites have the smallest particles size and TiO2/P25 nanocomposites were the largest crystal size. A SAED image reveals a ring structure that indicates a polycrystalline structure with some agglomeration. The arcs of the ring in Fig. 4a show some preferred orientation (low crystallinity). On the other hand, the diffraction pattern in Fig. 4b and c shows very sharp rings, which indicate very fine nanoparticles with polycrystalline structure (high crystallinity). On the contrary, SAED of TiO2/UV 100 nanocomposites reveals weak crystallinity due to very small nanoparticles (Fig. 4d). Almost all used nanomaterials were sufficient in the removal of phenol, where the removal rate reached 100% by using mesoporous nanoparticles. On the other hand, the removal efficiency was limited in the case of (TiO2/Ta2O5); it reached only 36% (Fig. 5). The removal rate by mesoporous TiO2 is much higher than those obtained by Mangrulkar et al. (2008); they used mesoporous MCM-41; around 44% removal was achieved, after 24 h. of irradiation. On the other hand, these results agreed with the results of Wang et al. (2012), where the removal rate reached 99% after 3-h irradiation time in batch treatment.
Germination and plant growth
The seeds start to grow sharply until it reaches the maximum germination ratio; then, it remains constant. The maximum germination ratio for both irrigated groups with the treated wastewater and Nile water was about 71%, while it was about 16.6% in seeds, which directly irrigated with untreated raw wastewater (Fig. 6). While the germination percentage for beans indicated that using raw water with a high concentration of phenol made the maximum germination ratio which is about 30%, no ability of plants continues to grow up. On the other hand, irrigation with treated wastewater achieved a germination ratio up 70%, which agree with Springer and Mornhinweg (2019); they reported that, after 7 days, the germination ratio of barley, winter malt 50.1b, and seeds was 70.6% with greenhouse environment condition of 15 and 25◦C and artificial light to provide for a 13-h/day length (Table 2).
Growth of barley and bean
The results showed that the average plant lengths of barley were 5.82 cm, 1.45 cm, and 8.96 cm with dry weight of 0.38 g, 0.12 g, and 0.45 g, and the average plant lengths of beans were 1.02 cm, 0.6 cm, and 0.92 cm with dry weight of 7.59 g, 4.97 g, and 9.95 g) in case of Nile water, raw wastewater, and treated water. It was noticed that the seeds irrigated with the treated water showed an improvement in growing up compared with those irrigated with raw wastewater and the Nile water under the redundancy of nutrients, nitrogen, and phosphorus in treated water. Moriyama et al. (2020) mentioned that the presence of nitrogen and phosphorus in irrigation water increases the oven-dried plant weight by about 100%.
Statistical analysis
The data obtained from the statistical analysis by using ANOVA and LSD show that both for barley and bean there was no significant difference between germination in the case of Nile and treated water. On the contrary, the results indicated that there is a significant difference between the germination in the case of Nile water at raw wastewater and this returns to the toxic effect of phenol in irrigation water, which damages the seed cells (Table 3).
Conclusion
This study introduced an integrated system that could deal with all different pollutants in pharmaceutical wastewater either they were toxic or not. The treatment route of pharmaceutical wastewater depends mainly on the nature of its pollutants. Conventional chemical treatment can be used as a pretreatment to remove apart of organic load; economic route includes calcium oxide (CaO), coagulant, that can achieve the removal of near 50% of total COD for wastewater with high content of TSS. AOPs including Fenton oxidation, nanomaterials, and nanocomposites are recommended in case of highly toxic or non-biodegradable wastewater with lower values of BOD/COD ratio to avoid higher treatment costs. This research provided an integrated system for the treatment of different kinds of pharmaceutical wastewater, more than 99% removal of COD, 100% removal of phenols, and disinfected effluents that were examined as a safe source of irrigation water in comparison with Nile water.
Data availability
The datasets used or analyzed during the current study are available from the corresponding author on reasonable request.
References
Aguilar-Perez KM, Aviles-Castrillo JI, Ruiz-Pulido G (2020) Nano-sorbent materials for pharmaceutical-based wastewater effluents—an overview. Case Stud Chem Environ Eng 2:100028. https://doi.org/10.1016/j.cscee.2020.100028
APHA (2017) Standard methods for the examination of water and wastewater, 23rd edn. In: Prepared and published jointly by American Public Health Association, American Water Works Association and Water Environment Federation, APHA 800 l Street, NW, Washington, DC 20001-3710
Azizan NAZ, Yuzir A, Al-Qaim FF, Abdullah N (2020) Anaerobic treatment performance in presence of pharmaceutically active compounds. In: IOP conference series: earth and environmental science, volume 479, the 7th AUN/SEED-net regional conference on natural disaster, pp 25–26. https://doi.org/10.1088/1755-1315/479/1/012029
Bagheri H, Afkhami A, Noroozi A (2016) Removal of pharmaceutical compounds from hospital wastewaters using nanomaterials: a review. Anal Bioanal Chem Res. https://doi.org/10.22036/abcr.2016.12655
Changotra R, Rajput H, Paul Guin J, Varshney L, Dhir A (2019) Hybrid coagulation, gamma irradiation and biological treatment of real pharmaceutical wastewater. Chem Eng J. https://doi.org/10.1016/j.cej.2019.03.256
Cincinelli A, Martellini T, Coppini E, Fibbi D, Katsoyiannis A (2015) Nanotechnologies for removal of pharmaceuticals and personal care products from water and wastewater. A review. J Nanosci Nanotechnol. https://doi.org/10.1166/jnn.2015.10036
ECP 501 (2015) Egyptian code of practice for the use of treated municipal wastewater for agricultural purposes. The Ministry of Housing Utilities and Urban Communities, n.d. No title
Eessaa AK, El-Shamy AM, Reda Y (2018) Fabrication of commercial nanoporous alumina by low voltage anodizing. Egypt J Chem 61(1):175–185. https://doi.org/10.21608/ejchem.2017.2189.1175
El-Shamy AM, El-Boraey HA, El-Awdan HF (2017a) Chemical treatment of petroleum wastewater and its effect on the corrosion behavior of steel pipelines in sewage networks. J Chem Eng Process Technol 8:1. https://doi.org/10.4172/2157-7048.1000324
El-Shamy AM, Farag HK, Saad W (2017b) Comparative study of removal of heavy metals from industrial wastewater using clay and activated carbon in batch and continuous flow systems. Egypt J Chem 60(6):1165–1175. https://doi.org/10.21608/ejchem.2017.1606.1128
El-Shamy AM, Abdelfattah I, Elshafey OI, Shehata MF (2018) Potential removal of organic loads from petroleum wastewater and its effect on the corrosion behavior of municipal networks. J Environ Manag 219:325–331. https://doi.org/10.1016/j.jenvman.2018.04.074
Farag HK, El-Shamy AM, El Sherif EM, Abedin SZ (2016) Sonochemical synthesis of nanostructured ZnO/Ag composites in an ionic liquid. Z Phys Chem 230(12):1733–1744. https://doi.org/10.1515/zpch-2016-0777
Fawzy ME, Abdelfattah I, Abuarab ME, Mostafa E, Aboelghait KM, El-Awady MH (2018) Sustainable approach for pharmaceutical wastewater treatment and reuse: case study. J Environ Sci Technol. https://doi.org/10.3923/jest.2018.209.219
Ferrari B, Paxéus N, Giudice RL, Pollio A, Garric J (2003) Ecotoxicological impact of pharmaceuticals found in treated wastewaters: study of carbamazepine, clofibric acid, and diclofenac. Ecotoxicol Environ Saf. https://doi.org/10.1016/S0147-6513(02)00082-9
Ismail AA, Bahnemann DW (2011) Mesoporous titania photocatalysts: preparation, characterization and reaction mechanisms. J Mater Chem. https://doi.org/10.1039/c1jm10407a
Jacob PT, Siddiqui SA, Rathore MS (2020) Seed germination, seedling growth and seedling development associated physiochemical changes in Salicornia brachiata (Roxb.) under salinity and osmotic stress. Aquat Bot. https://doi.org/10.1016/j.aquabot.2020.103272
Jeong H, Kim H, Jang T (2016) Irrigation water quality standards for indirect wastewater reuse in agriculture: a contribution toward sustainable wastewater reuse in South Korea. Water (switzerland). https://doi.org/10.3390/w8040169
Klavarioti M, Mantzavinos D, Kassinos D (2009) Removal of residual pharmaceuticals from aqueous systems by advanced oxidation processes. Environ Int. https://doi.org/10.1016/j.envint.2008.07.009
Malik SN, Khan SM, Ghosh PC, Vaidya AN, Kanade G, Mudliar SN (2019) Treatment of pharmaceutical industrial wastewater by nano-catalyzed ozonation in a semi-batch reactor for improved biodegradability. Sci Total Environ. https://doi.org/10.1016/j.scitotenv.2019.04.097
Mangrulkar PA, Kamble SP, Meshram J, Rayalu SS (2008) Adsorption of phenol and o-chlorophenol by mesoporous MCM-41. J Hazard Mater. https://doi.org/10.1016/j.jhazmat.2008.03.013
Moriyama Y, Yamaura H, Fukui R, Becker JO (2020) The role of phosphorus in growing tomatoes in near water-saturated soil. J Plant Nutr. https://doi.org/10.1080/01904167.2020.1724302
Mylapilli SVP, Reddy SN (2019) Sub and supercritical water oxidation of pharmaceutical wastewater. J Environ Chem Eng. https://doi.org/10.1016/j.jece.2019.103165
Nasr FA, Abdelfattah I, Shana AM (2019) Cost-effective physicochemical treatment of carpet industrial wastewater for reuse. Egypt J Chem. https://doi.org/10.21608/EJCHEM.2018.5191.1465
Rodríguez-Felix F, Lopez-Cota AG, Moreno-Vasquez MJ, Graciano-Verdugo AZ, Quintero-Reyes IE, Del-Toro-Sanchez CL, Tapia-Hernandez JA (2021) Sustainable-green synthesis of silver nanoparticles using safflower (Carthamus tinctorius L.) waste extract and its antibacterial activity. Heliyon 7:e06923. https://doi.org/10.1016/j.heliyon.2021.e06923
Saleem M (2007) Pharmaceutical wastewater treatment: a physicochemical study. J Res Sci B Z Univ 18(2):125–134
Shahab H, Azimian-Kivi M, Yoones J, Reza Y (2021) Pharmaceutical wastewater treatment using polypropylene membranes incorporated with carboxylated and PEG-grafted nanodiamond in membrane bioreactor (MBR). Water Environ J. https://doi.org/10.1111/wej.12715
Shehata MF, El-Shafey S, Ammar NA, El-Shamy AM (2019) Reduction of Cu+2 and Ni+2 ions from wastewater using mesoporous adsorbent: effect of treated wastewater on corrosion behavior of steel pipelines. Egypt J Chem 62(9):1587–1602. https://doi.org/10.21608/ejchem.2019.7967.1627
Springer TL, Mornhinweg DW (2019) Seed germination and early seedling growth of barley at negative water potentials. Agronomy. https://doi.org/10.3390/agronomy9110671
Wang F, Hu Y, Guo C, Huang W, Liu CZ (2012) Enhanced phenol degradation in coking wastewater by immobilized laccase on magnetic mesoporous silica nanoparticles in a magnetically stabilized fluidized bed. Bioresour Technol. https://doi.org/10.1016/j.biortech.2012.01.184
World Health Organization (2006) World Health Organization guidelines for the safe use of wastewater, excreta, and greywater. WHO, Geneva
Zhang M-H, Dong H, Zhao L, Wang D-x, Meng Di (2019) A review on Fenton process for organic wastewater treatment based on optimization perspective. Sci Total Environ 670(20):110–121. https://doi.org/10.1016/j.scitotenv.2019.03.180
Acknowledgements
The authors greatly thank the National Research Center for supporting this work through internal Project No. 11070107.
Funding
Open access funding provided by The Science, Technology & Innovation Funding Authority (STDF) in cooperation with The Egyptian Knowledge Bank (EKB). This work was supported by own.
Author information
Authors and Affiliations
Contributions
IA, MA and EM analyzed the data and wrote the manuscript; HE-A acts as a consultant for the scientific information; KA designed and supported the experiment, and AE-S helped perform the analysis with constructive discussions.
Corresponding author
Ethics declarations
Conflict of interest
The authors declare no competing interests.
Ethical approval
Ethical approval was obtained from the Water Pollution Research, Agricultural Engineering and Physical Chemistry Cairo University and National Research Centre.
Consent to participate
All authors are informed and agree to the study.
Consent to publish
All the authors agree to publication in the journal.
Additional information
Editorial responsibility: Samareh Mirkia.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Abdelfattah, I., Abuarab, M.E., Mostafa, E. et al. Integrated system for recycling and treatment of hazardous pharmaceutical wastewater. Int. J. Environ. Sci. Technol. 20, 4101–4110 (2023). https://doi.org/10.1007/s13762-022-04269-7
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13762-022-04269-7