Abstract
The proper selection of drilling fluids formulations and its treatment has always been a challenge and requires a great effort to ensure optimum drilling performance. The objective of this paper is to assist the mud engineer in selecting the water-based drilling fluid formulations that are best suited for a certain application. To achieve this target, the field practices were combined with the literature to study the most practiced water-based drilling fluid recipes used for onshore gas applications in the Middle East (i.e., spud mud, high-bentonite spud mud, salt/polymer mud, and high-overbalanced mud). From both field practices and deep literature review, it is recommended that both spud mud and high-bentonite spud mud be prepared and pre-hydrated for 4–6 h before a well spud. Also, it is important to add detergents with high-viscosity sweeps to avoid the bit balling and maintain the gel strength. While for salt/polymer mud, the regular addition of sodium sulfite is necessary for polymers stabilization, and the efficient solids control equipment performance is essential. To avoid the solids sagging issues associated with drilling high-pressure high-temperature deep gas reservoirs, it is recommended to either uses sag resistance materials, micronized weighting materials, or a combination of different weighting materials. The high-overbalanced mud is the most effective and efficient type when drilling a combination of natural fractured depleted gas reservoirs with high-pressure gas reservoirs.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
Drilling fluids have a crucial continued role in drilling a successful well. They are designed to perform a variety of important functions at once. These functions are mainly controlling of subsurface pressures, carrying out and suspension of drill cuttings, maintaining of wellbore stability, minimizing formation damage, cooling and lubricating of the drill string and drill bit, sealing of permeable formations, transmitting hydraulic energy to downhole tools, and providing sufficient information for formation evaluation [1,2,3].
Generally, drilling fluids are composed of a continuous phase, either liquid or gas, mixed with active/inactive solids and chemicals. Based on the continuous phase, the drilling fluids are classified into three main types: (a) aqueous drilling fluids referred to as water-based mud, (b) nonaqueous drilling fluids also called oil-based mud, and (c) gaseous-based mud [2,3,4,5]. In the gaseous-based mud, gas or gas–liquid mixtures are used to be the continuous phase. This type of drilling fluid is not commonly used and applicable for drilling in depleted fields, where the depletion of the formation fluid generated a low formation pressure profile [1, 6]. In oil-based muds, the continuous phase is either synthetic oil or petroleum products, but the water can be added to form an invert emulsion. These drilling fluids are used much less frequently compared to water-based muds because of its high cost and the associated environmental concerns and legislations. However, they are beneficial in drilling horizontal wells and water-sensitive formations [4, 7,8,9].
The most common type of drilling fluids used in drilling operations is the water-based drilling fluid (WBDF). It consists of a mixture of solids, water, and chemicals, where solids might be active or inactive depending on its reaction with a water base and dissolved chemicals. The active solids (e.g., clays) react with water or dissolved chemicals to perform certain functions, unlike the inactive solids (e.g., sand) which do not react with water and chemicals to any significant degree. The used water might be seawater, brine, or freshwater, whichever is appropriate or available [2, 3, 10,11,12].
Many issues and problems associated with drilling operations are mainly affected by drilling fluids properties. These challenges, such as stuck pipe, wellbore instability, lost circulation, formation damage, and shale heaving, can be avoided eventually using a variety of additives types to maintain the key properties. The most common additives include densifiers, viscosifiers, rheology controllers, lost circulation controllers, filtration controllers, shale stabilizers, and alkalinity controllers [11, 13].
Considering the applied additives, i.e., rheological properties controllers and inhibition ions, the WBDF can be classified into four categories: (a) non-dispersed-non-inhibited mud system, in which neither rheology controllers nor inhibitors are contained, (b) dispersed-non-inhibited mud, that contains rheology controllers; however, the inhibitors were not utilized, (c) non-dispersed-inhibited mud contains inhibitors but not rheological properties controllers, and (d) dispersed-inhibited mud contains both rheological controllers and inhibition ions [2, 14,15,16].
The appropriate drilling fluids selection and design for drilling operations are governing by many key factors, such as formation type, pressure, temperature, well trajectory, economics, and environmental restrictions. To consider these factors, the collection of offset wells data, geological data, and others are necessitated. Generally, the proper selection of drilling fluids systems and its treatment has always been a challenge and requires a great effort to ensure optimum drilling performance [6, 11, 17, 18].
The objective of this paper is to assist the mud engineer in selecting the WBDF formulation that best suited for a certain application. To achieve this target, the field practices were combined with the literature to study the most practiced WBDF recipes in the middle east, which are used for onshore gas applications. These formulations were discussed from both theoretical and practical points of view, in terms of the composition, properties, drilled section/formation characteristics, potential problems, and recommendations, and supported by field cases.
2 Drilling Fluids Formulations
From the literature, the WBDF can be classified and described based on its composition as shown in Table 1. The common WBDF recipes used in the middle east, including spud mud, high-bentonite spud mud, salt/polymer mud, and high-overbalanced mud, will be discussed herein.
2.1 Spud Mud
The Spud mud is a formula of WBDF that is mainly categorized as non-dispersed-non-inhibited mud and used for drilling the shallow formations with large diameter hole (i.e., 36″–26″). It is composed of flocculated bentonite (mainly smectite/montmorillonite mineral) that is qualified for providing and maintaining the required viscous properties. This mud with its simple compositions will demonstrate the desired rheological properties for carrying out the large gravel cuttings from the shallow depth. However, weighting material might be used to maintain hole stability. Loss of circulation is highly likely to occur while drilling the soft shallow formations, so the loss of circulation control materials often be used [19, 20].
2.1.1 Composition and Properties
The spud mud is formed mainly by bentonite and water, but other functional additives (i.e., pH controller, weighting material, thinner and fluid loss controller) are required to maintain the mud properties in a range of 64–67 pcf (pound per cubic feet) for density, 7–10 of API filtrate and as low as a possible value of plastic viscosity. The most practiced composition of spud mud is listed in Table 2 with the average properties.
2.1.2 Drilled Section Characteristics
Considering a field case, two sections were drilled using the spud mud. These sections contain five formations as shown in the lithology column in Fig. 1(i). Formations A, B, and C were drilled with 34″-hole section while D, E, and F were drilled with 28″-hole section. Formation A is exposed at the surface and composed mainly of layers of sandstone, claystone, limestone, and marl with minor streaks of anhydrite and traces of chert. Formation B constitutes of dolomite and limestone with streaks of marl and claystone. Formation C contains anhydrite occasionally with very minor streaks of dolomite and limestone. Formation D is composed of dolomitic limestone with minor streaks of anhydrite and claystone especially toward the lower part. Formation E constitutes mainly of limestone interbedded with shale layers.
2.1.3 Operational Practices
The spud mud is prepared by pre-hydrating bentonite clay and diluting in the base water by 25–50 lb/bbl. To ensure the proper hydration of bentonite, the soda ash and caustic soda should be used for lowering the concentration of calcium and magnesium ions, respectively, in the make-up water to be less than 200 mg/l, that will adjust the pH to above 10, as well [21, 22]. The thinner and weighting material might be used to alter the properties if required.
The spud mud should be prepared for 4–6 h before using to warrant yielding the clay.
Since hole cleaning is affected by the solids control equipment, mud density, rheology, and cuttings characteristics; 80 mesh screens are utilized to handle a typical flow rate of 1000–1200 gpm (gallon per minute) and the de-sander and de-silter are used to discard the solids.
Practically, a loss of mud is allowed over the shakers to discard the maximum number of solids and maintain the lowest possible mud density in the active pits. Moreover, 100 bbl of high-viscosity sweeps is used every 30–45 ft together with reaming, and the swept volume is increased if there is a sign of hole instability or poor hole cleaning.
2.1.4 Problems and Recommendations
The bit balling problem will be experienced with the bentonite system if clay swelling is not inhibited. To reduce the occurrence of that, specific types of dispersant dubbed drilling detergent with high-viscosity pills are recommended to be used. This will help in carrying out the cuttings from the wellbore.
Based on the drilled section characteristics, a total fluid loss is the potential to occur. So, it is recommended to continue drilling 100–150 ft with mud, then switch to inhibited water and sweep hole with high-viscosity sweeps made from high-bentonite content.
In case of hole instability is a concern, inhibited partially hydrolyzed polyacrylamide (PHPA) mud and weighted high-viscosity sweep of 75 pcf are used to maintain the mud density at 63–64 pcf and pH at 9–10.
2.2 High-Bentonite Spud Mud
Surface hole formations have a low-pressure profile which promotes the possibility of circulation losses in specific geological horizons, besides the reduction in drilling rate of penetration caused by using bentonite [23]. Therefore, it had been recommended to use invert-emulsion mud. But, because of the environmental constraints, the invert-emulsion mud has a restriction when drilling the surface hole. As a result, and to help in averting losses of circulation; a high-bentonite spud mud has been introduced to drill such hole section.
2.2.1 Composition and Properties
The high-bentonite spud mud has the same components as the spud mud but with higher concentrations of flocculated bentonite and a thinner additive is required. An anti-microbial agent such as biocide may be required. The properties of this mud should be in a range of 67–69 pcf for density, 5–8 of API filtrate, and as low as a possible value of plastic viscosity. Table 3 shows the practically used composition for the high-bentonite spud mud and the averaging properties.
2.2.2 Drilled Section Characteristics
The high-bentonite spud mud is used to drill a 22″-hole section which is composed of five formations as depicted in Fig. 1(ii). Formation F is composed mainly of sandstone interbedded with shale and limestone layers. Formation G constitutes of calcarenite, dolomitic limestone. Formation H contains mainly high compressive strength sandstone with minor streaks of shale and limestone. Formation I is composed of limestone with streaks of sandstone and shale. Formation J constitutes mainly of limestone.
2.2.3 Operational Practices
The high-bentonite spud mud is prepared similarly as the spud mud for 4–6 h before a well spud and pre-hydrated 40–50 lb/bbl of bentonite clay in the makeup water. Soda ash, caustic soda, and thinner will be used. The weighting material might be added to alter the properties if required.
The practical flow rate used to drill a section with the high-bentonite spud mud is 900–1000 gpm, which requires 60 mesh screens to be utilized. De-sanders and de-silters are used to discard as many solids as possible. For better hole cleaning, 75 bbl of high-viscosity sweeps is used every 30–45 ft.
2.2.4 Problems and Recommendations
Since the system contains a high concentration of bentonite, the bit balling problem is a concern. Therefore, detergents with high-viscosity pills are used.
From field practice, the optimum value of the methylene blue test (MBT) measurement, which indicates the active clay content in the mud, is 40–50 lb/bbl bentonite equivalent. But while drilling across formations that contain streak of shales (e.g., formations H and I), the MBT value will increase. So, a dilution rate of 20–25 bbl of water is used to maintain the MBT at the specific range.
When drilling into a formation containing a high compressive strength sandstone, such as formation H, the rate of penetration (ROP) is dropped significantly. The MBT, therefore, is recommended to be reduced to 25 Ib/bbl bentonite equivalent to enhance the drilling performance. Moreover, if a trip is made at casing point depth, it is recommended to add a powdered dispersant thinner to maintain the MBT and gel strength. That will minimize the effect of surge and swab pressures.
In case of total fluid losses encountered (e.g., taking place in formations F and G) or the borehole shows any instability or sticking tendency, it is recommended to switch to the PHPA mud system, and 75 pcf of mud cap to be pumped continuously into the annulus. This will maintain the maximum visible fluid level and prevent the water flow from formations (as occurred in formation F).
The drilling field data indicates that the ROP is reduced when using the high-bentonite mud comparing with invert-emulsion mud, as shown in Fig. 2. This reduction in the ROP is mainly due to the high-bentonite effect on the mud rheological properties [24]. Therefore, it is recommended to add thinner for the mud formula to control the mud viscosity.
2.3 Salt-Polymer Mud
Unstable shales and hard salt formations, that composed of sodium, magnesium, or potassium chlorides, are penetrated in many drilling areas. In which, using the oil-based mud has better performance and stability [25]. However, to be in line with the environmental regulations, an environmentally acceptable alternative WBDF (i.e., salt/polymer mud) has been developed to supersede the use of oil-based mud [26,27,28,29].
The salt/polymer mud is used to maintain shale stabilization and to avoid shale sloughing and hole enlargement caused by the dissolution of formation-salt [29]. Besides, it is used for high-pressure high-temperature (HPHT) conditions with a limitation of temperature up to 300 °F [30,31,32,33]. The key mud properties that need to be controlled are mainly mud salinity, density, rheology, filtration properties, and pH [29, 34].
2.3.1 Composition and Properties
The typical salt polymer mud contains mainly (a) base water, (b) pre-hydrated bentonite to viscosify the mud, (c) sodium or potassium salts (NaCl/KCl) for clay hydration inhibition, (d) a combination of anionic polymers such as xanthan gum (XC polymer) and polyanionic cellulose (PAC) for viscosity buildup and filtration control, (e) either caustic soda, caustic potash or soda ash to control the alkalinity, (f) starch for fluid loss control at low temperature, (g) barite as weighting material, (h) calcium carbonate (CaCO3) as a bridging agent, (i) sodium asphalt sulfonate to improve filter cake properties, and (j) lignosulfonate to enhance the gel strength at high temperature [35, 36]. Tables 4 and 5 present the practical compositions for salt polymer mud used with normal and high densities for HPHT, respectively.
2.3.2 Drilled Section Characteristics
From the field case, the salt polymer mud is used to drill two sections. The first section has a 16″-hole and contains five formations (K–O) as described in the lithology column; Fig. 1(iii). Formations K and L are composed of layers of calcarenite and anhydrite with minor streaks of limestone. Formation M contains limestone and calcarenite. Formation N constitutes of limestone with minor streaks of calcarenite, claystone, and anhydrite. Formation O is composed mainly of sandstone interbedded by shale, siltstone, anhydrite, and limestone. The second section has a 12″-hole and contains three formations (P, Q, and R) as shown in Fig. 1(iv) and considered as HPHT formations. Formation P contains mainly of dolomitic with streaks of anhydrite and shale. Formation Q is composed mainly of shale with streaks of anhydrite, siltstone, and dolomitic. Formation R constitutes mainly of dolomite with interbeds of shale, limestone, and anhydrite.
2.3.3 Operational Practices
A low mud density of 67 pcf is used to start drilling the section to build up a filter cake, especially in some formations, such as formation K and the upper part of formation L, which have a potential risk of losses. Then, the mud density is raised to a certain level to overbalance the lower formation L pressure.
For this drilled section, when the static bottom-hole temperature (BHT) reaches 230 °F or If HPHT filtration control becomes problematic because of BHT, PAC low viscosity is introduced at 0.5–2 lb/bbl as required to control fluid loss especially at lower formations N and O. Small additions of sodium sulfite would remove the oxygen and stabilize the polymers to a bottom hole temperature up to 280 °F.
An efficient solids control equipment performance is essential to control mud density and viscosity, hence, minimize the probability of loss of circulation. 100 mesh screens are used to utilize the practical flow rate of 650 gpm.
It is possible to lose circulation when drilling into depleted formations. Therefore, it is highly recommended to conduct an API-HPHT filtration test before entering such formations.
A mud cap is pumped continuously in the annulus to maintain the maximum visible fluid level to prevent any flow from protentional formations. For a better hole cleaning, 75 bbl of a high-viscosity sweep is used every 45 ft.
When drilling through a section with HPHT formations (i.e., formations P, Q, and R), high mud density (up to 150 pcf) is required, and regular additions of sodium sulfite (1 can every 4–6 h) while drilling is necessary to stabilize the polymers to a bottom hole temperature up to 300 °F. 120–140 API mesh shaker screens are recommended for this hole section.
Any treatment should be pilot tested before adding to the active system, this is very crucial on this type of mud as any undesired addition can lead to excessive rheology or an increase in fluid loss properties. Once the final formulation is achieved, a visual sag settling test is performed at ambient temperature for 12 h.
2.3.4 Problems and Recommendations
CO2 influx may take place in the mud, so frequent measurement of alkalinities is required. In the case of CO2 influx occurrence, caustic soda and lime are effective in removing CO2. If H2S has been detected, the drilling fluid should be treated with chemical scavengers.
At HPHT conditions (i.e., formations P, Q, and R), where higher density mud is required to suppress the formation pressure [37], the settling rate of barite solid particles is increased [38]. This settlement is known as a sagging phenomenon and is affected by the drilling fluid properties and drilling parameters [39,40,41]. This issue may eventually result in the stuck pipe, wellbore instability, loss of circulation, and inconsistent rheological properties [40, 42, 43].
Several studies were conducted to introduce successful solutions for the sagging issue either by optimizing drilling fluid rheology using anti-sagging agents and rheology modifiers [44,45,46,47,48], reducing the particle size of the weighting material such as micronized barite and ilmenite [37, 49,50,51], or using a combination of different weighting materials [52,53,54,55,56,57,58].
2.4 High-Overbalanced Mud
Oil- and synthetic-based muds are considered as the technical choice to overcome the challenges associated with formations that have highly reactive clays and shale, microfractures, and highly stressed fractured formations. Also, these muds are preferable when drilling low formation pressures with a narrow operating margin between the pore pressure and formation breakdown, which does not allow for increased drilling fluid density and consequently experiences extremely overbalanced pressures. Such formations will result in high-pressure transmission, sloughing shale, loss of circulation, and differential sticking.
But, because of the increased rigid environmental restrictions, further alternative WBDFs development has been encouraged [59, 60]. These alternatives are called high-overbalanced mud, also known as high-performance water-based mud (HPWBM).
The HPWBM is practically used to drill the ultra-deep gas wells and to drill through commingled low and high-pressure formations in one single hole section, such as the combined depleted reservoirs with high-pressure reservoirs, as illustrated in Fig. 3. This special mud bridges along the walls of the well and tolerates the very high differential pressure. In which, the overbalance pressure is within the range of 1000–5000 psi comparing to 200–500 psi for normal overbalance pressure. Using this (HPWBM) will secure the drilling operations whether above or through the target reservoir section, which indeed reduces the total cost of the well. The HPWBM is commonly practiced for gas wells drilling in the middle east. [61, 62].
2.4.1 Composition and Properties
An efficient HPWBM has four criteria to achieve superior drilling performance, these criteria are: (a) low colloidal content; by providing means to chemically flocculate and encapsulate the ultrafine particles to promote higher penetration rate, (b) effective shale inhibitive; by inhibiting the reactive clay to maximize the stability, (c) shear-thinning behavior; for adequate hole cleaning, and (d) non-dispersed system; to reduce solids contamination and build the filter cake with lubricious hydrated polymers instead of being laden with ultrafine drill solids [63]. To fulfill all, not just some, of these high-performance criteria, polymeric additives and commercial sized particulate materials are required.
Table 6 shows an example of an HPWBM recipe with its practical composition and properties using trademarked products.
2.4.2 Drilled Section Characteristics
The HPWBM system is used to combine drilling through natural fractured depleted gas reservoir (such as formation R that described previously) with high-pressure gas reservoirs such as formations S, T, and U.
As described in Fig. 1(v), formation S is composed mainly of sandstone with minor streaks of shale and siltstone, and formation T contains shale with interbeds of dolomite and siltstone, while formation U constitutes mainly of sandstone with minor streaks of shale, siltstone, limestone, and dolomite. The hole size for this section was \( 5{\raise0.7ex\hbox{$7$} \!\mathord{\left/ {\vphantom {7 8}}\right.\kern-0pt} \!\lower0.7ex\hbox{$8$}}^{\prime \prime } \).
2.4.3 Operational Practices
Using the resilient carbon bridging material (e.g., STEELSEAL®) has a significant advantage when drilling a combination of natural fractured depleted gas reservoirs with high-pressure gas reservoirs. A unique feature of the STEELSEAL® is resiliency, which allows it to mold itself in the tip of the fracture. If the pressure increases further and the fracture opens-up, the STEELSEAL® rebounds itself, thus continuing to plug the fracture completely.
The quantity of each bridging material of the system including STEELSEAL®, BAROFIBRE®, and BARACARB® is determined based on the D50 of the particle size distribution (PSD).
After the formulation of the bridging is optimized, the permeability plugging test (PPT) is performed in a specialized filtration-type apparatus to determine the effectiveness of the bridging system. The applied pressure usually is equivalent to the maximum overbalance that will be seen while drilling plus 500 psi.
To maintain the HPWBM and keep it within capable specifications, more attention and manpower are required, which strains the limited crew number.
3 Summary
In this paper, most of the water-based drilling fluid formulations used for onshore gas drilling applications were studied, from both theoretical and practical points of view, and supported by field cases.
The spud mud is an inexpensive mud used for surface hole drilling and composed mainly of flocculated bentonite and water. It is recommended to add detergents with high-viscosity sweeps to avoid the bit balling and help in carrying out the cuttings. Also, in the case of hole instability, the inhibited PHPA mud will be used.
The high-bentonite spud mud is a specialized formula of the spud mud, used as an alternative for invert-emulsion mud, and applied for drilling shallow sections with specific geological horizons and extreme fluid losses. A dilution rate of 20–25 bbl of water and powdered dispersant thinner is practically used to maintain the MBT and gel strength, respectively. That will minimize the effect of surge and swab pressures. It is recommended to switch to PHPA mud at the hole instability. Both spud mud and high-bentonite spud mud should be prepared and pre-hydrated for 4–6 h before a well spud.
To drill unstable shales and hard salt formations, the salt/polymer mud is used for maintaining shale stabilization for both conventional and HPHT conditions. With this mud type, the regular addition of sodium sulfite while drilling is necessary to stabilize the polymers to a bottom hole temperature up to 300 °F. Moreover, to avoid the solids sagging issues associated with drilling HPHT deep gas reservoirs, it is recommended to either uses sag resistance materials, micronized weighting materials, or a combination of different weighting materials.
The HPWBM has a significant advantage when drilling a combination of natural fractured depleted gas reservoirs with high-pressure gas reservoirs, in which a high overbalanced drilling is necessary. The HPWBM is developed from polymeric additives and commercial sized particulate materials by combining mainly resilient graphite carbon, fibrous materials, and sulfonated asphalt. It behaves like oil- and synthetic-based muds in forming a unique system that provides a well-lubricated gauge wellbore.
Abbreviations
- ALAP:
-
As low as possible
- bbl:
-
Barrel
- BHT:
-
Bottom-hole temperature
- gpm:
-
Gallon per minute
- HPHT:
-
High pressure high temperature
- HPWBM:
-
High-performance water-based mud
- LSYP:
-
Low-shear yield point
- MBT:
-
Methylene blue test
- PAC:
-
Polyanionic cellulose
- pcf:
-
Pound per cubic feet
- PHPA:
-
Partially hydrolyzed polyacrylamide
- PPT:
-
Permeability plugging test
- PSD:
-
Particle size distribution
- PV:
-
Plastic viscosity
- ROP:
-
Rate of penetration
- WBDF:
-
Water-based drilling fluid
- XC:
-
Xanthan gum
- YP:
-
Yield point
References
Rabia, H.: Well Engineering and Construction. Chapter 7, pp. 265–302. Entrac Consulting, London (2002). ISBN-13: 978-0954108700
Growcock, F.; Harvey T.: Drilling Fluids Processing Handbook. Chapter 2, by ASME Shale Shaker Committee, pp. 15–68. Gulf Professional Publishing (2004). ISBN 978-0-7506-7775-2
Scott, P.; Broussard, P.; Freeman, M.; Growcock, F.; Bland, R.: IADC Drilling Manual, Chapter 10. IADC, Houston, Texas (2015)
Bernier, R.; Garland, E.; Glickman, A.; Jones, F.; Mairs, H.; Melton, R.; Ray, J.; Smith, J.; Thomas, D.; Campbell, J.: Environmental aspects of the use and disposal of non aqueous drilling fluids associated with offshore oil and gas operations. Technical Report, No. 342, International Association of Oil and Gas Producers (2003)
Caenn, R.; Darley, H.C.H.; Gray, G.R.: Composition and Properties of Drilling and Completion Fluids, Chapter 1, 6th edn. Gulf Professional Publishing, Amsterdam (2011). ISBN 9780123838599
Bourgoyne, J.A.T.; Millheim, K.K.; Chenevert, M.E.; Young, J.F.S.: Applied Drilling Engineering, Chapter 2, vol. 2, pp. 42–84. Society of Petroleum Engineers, Richardson, TX (1991). ISBN 978-1-55563-001-0
Roberts, D.J.; Nguyen, A.H.: Degradation of synthetic-based drilling mud base fluids by Gulf of Mexico sediments: final report. New Orleans, LA. U.S. Dept. of the Interior, Minerals Management Service, Gulf of Mexico OCS Region, Access Number: 31179 (2006)
Hussein, A.M.O.; Amin, R.A.M.: Density measurement of vegetable and mineral based oil used in drilling fluids. Paper SPE-136974-MS. Presented at the 34th Annual SPE International Conference and Exhibition, Calabar, Nigeria, 31 July–7 August (2010). https://doi.org/10.2118/136974-MS.
Fadairo, A.; Falode, O.; Ako, C.; Adeyemi, A.; Ameloko, A.: Novel formulation of environmentally friendly oil based drilling mud, Chapter 3. In: Gomes, J.S. (ed.) New Technologies in the Oil and Gas Industry, pp. 49–80. IntechOpen, London (2012). https://doi.org/10.5772/51236. ISBN 978-953-51-0825-2
Fink, J.K.: Petroleum Engineer’s Guide to Oil Field Chemicals and Fluids, Chapter 1, pp. 1–59. Gulf Professional Publishing (2012). ISBN: 9780128037355. https://doi.org/10.1016/c2009-0-61871-7
Hamoodi, A.; Rahimy, A.A.; Khalid, A.W.: The effect of proper selection of drilling fluid on drilling operation in janbour field. Am. Sci. Res. J. Eng. Technol. Sci. 39(1), 224–234 (2018)
Jaiswal, A.; Verma, A.: Comparative studies of using aphron drilling mud versus spud mud. Int. J. Manag. IT Eng. 8(10), 74–81 (2018)
Mitchell, R.F.: Petroleum Engineering Handbook. Volume II: Drilling Engineering, edited by Larry W. Lake, Chapter 2, pp. 90–119. Society of Petroleum Engineers, Texas (2007). ISBN: 978-1-55563-114-7
Anderson, D.B.: Non-dispersed weighted muds. Paper SPE-3990, Presented at the 47th Annual Fall Meeting of the Society of Petroleum Engineers of AIME, San Antonio, Texas, 8–11, October (1972)
Blattel, S.R.; Rupert, J.P.: The effect of weight material type on rate of penetration using dispersed and non-dispersed water-base muds. Paper SPE-10961-MS, Presented at the 57th SPE Annual Fall Technical Conference and Exhibition, New Orleans, Louisiana, 26–29, September (1982). https://doi.org/10.2118/10961-MS
Kharitonov, A.; Burdukovsky, R.; Pogorelova, S.; Sidubaev. S.: The principles of selection and optimization of drilling fluid for drilling operations in the vankor field in Eastern Siberia. Paper SPE-166840, presented at SPE Arctic and Extreme Environments Conference and Exhibition. Moscow, Russia, 15–17, October (2013)
Bleier, R.: Selecting a drilling fluid. J. Pet. Technol. 42(7), 832–834 (1990). https://doi.org/10.2118/20986-PA
Bloys, B.; Davis, N.; Smolen, B.; Bailey, L.; Houwen, O.; Reid, P.; Sherwood, J.; Fraser, L.; Hodder, M.: Designing and managing drilling fluid. Oilfield Rev. 6(2), 33–43 (1994)
Taghiyev, F.; Hodne, H.; Saasen, A.: Using drill cuttings waste as resource for spud mud. Paper SPE/IADC-173033-MS, Presented at SPE/IADC Drilling Conference and Exhibition, London, 17–19, March (2015)
Abdelgawad, K.; Elkatatny, S.; Mousa, T.; Mahmoud, M.; Patil, S.: Real time determination of rheological properties of spud drilling fluids using a hybrid artificial intelligence technique. J. Energy Resour. Technol. 141(3), 1–9 (2019). https://doi.org/10.1115/1.4042233
Goud, M.: Mud engineering simplified. Chapter 4. Becomeshakespeare.com (2017). ISBN 978-9386487674
Praetorius, S.; Schößer, B.: Bentonite Handbook: Lubrication for Pipe Jacking, Chapter 6, pp. 49–103. Ernst & Sohn, Berlin (2017)
Beck, F.E.; Powell, J.W.; Zamora, M.: The effect of rheology on rate of penetration. Paper SPE-29368-MS, Presented at SPE/IADC Drilling Conference, Amsterdam, 28 February–2 March (1995). https://doi.org/10.2118/29368-MS
Li, M.C.; Wu, Q.; Song, K.; French, A.D.; Mei, C.; Lei, T.: pH-responsive water-based drilling fluids containing bentonite and chitin nanocrystals. ACS Sustain. Chem. Eng. 6(3), 3783–3795 (2018). https://doi.org/10.1021/acssuschemeng.7b04156
Bol, G.M.; Wong, S.W.; Davidson, C.J.; Woodland, D.C.: Borehole stability in shales. SPE Drill. Complet. 9(2), 87–94 (1994). https://doi.org/10.2118/24975-PA
Simpson, J.P.; Walker, T.O.; Jiang, G.Z.: Environmentally acceptable water-based mud can prevent shale hydration and maintain borehole stability. SPE Drill. Complet. 10(4), 242–249 (1995). https://doi.org/10.2118/27496-PA
Patel, A.; Stamatakis, E.; Friedheim, J.E.; Davis, E.:. Highly inhibitive water-based fluid system provides superior chemical stabilization of reactive shale formations. Paper AADE 01-NC-HO-55, Presented atAADE National Drilling Technical Conference. Houston, Texas, 27–29, March (2001)
Schlemmer, R.; Friedheim, J.E.; Growcock, F.B.; Bloys, J.B.; Headley, J.A.; Polnaszek, S.C.: Membrane efficiency in shale—an empirical evaluation of drilling fluid chemistries and implications for fluid design. Paper SPE-74557-MS, Presented at IADC/SPE Drilling Conference, Dallas, Texas, 26–28, February (2002). https://doi.org/10.2118/74557-MS
Fink, J.K.: Water-based chemicals and technology for drilling, completion, and workover fluids, 1st edn., Chapter 2, pp. 5–114. Gulf Professional Publishing (2015). ISBN: 9780128026434. https://doi.org/10.1016/B978-0-12-802505-5.00002-0
Amani, M.; Retnanto, A.; Yrac, R.; Shehada, S.; Ghamary, M.H.; Khorasani, M.H.M.; Abu Ghazaleh, M.: Effect of salinity on the viscosity of water based drilling fluids at elevated pressures and temperatures. Int. J. Eng. Appl. Sci. 7(4), 30–52 (2015)
Ofei, T.N.; Al Bendary, R.M.: Formulating water-based muds for high-temperature wellbores using potassium formate brine and synthetic polymers: a design of experiment approach. Paper SPE-180520-MS, Presented at IADC/SPE Asia Pacific Drilling Technology Conference, Singapore, 22–24 August (2016). https://doi.org/10.2118/180520-MS
Panamarathupalayam, B.; Manzoleloua, C.; Sebelin, L.; Aung, T.H.: Multifunctional high-temperature water-based fluid system. Paper SPE-195009-MS, Presented at SPE Middle East Oil and Gas Show and Conference, Manama, Bahrain, 18–21 March (2019). https://doi.org/10.2118/195009-MS
Pino, R.; Abouhamed, A.; Addagalla, A.; El Dakroury, H.: Not too hot to handle: water based fluid drills high temperature wells. Paper SPE-196796-MS, Presented at SPE Russian Petroleum Technology Conference, Moscow, 22–24 October (2019). https://doi.org/10.2118/196796-MS
Alcázar, L.A.; Cortés, I.R.: Drilling fluids for deepwater fields: an overview. In: Zoveidavianpoor, M. (ed.) Recent Insights in Petroleum Science and Engineering. IntechOpen, London (2017). https://doi.org/10.5772/intechopen.70093
Khodja, M.; Canselier, J.P.; Bergaya, F.; Fourar, K.; Khodja, M.; Cohaut, N.; Benmounah, A.: Shale problems and water-based drilling fluid optimisation in the Hassi Messaoud Algerian oil field. Appl. Clay Sci. 49(4), 383–393 (2010). https://doi.org/10.1016/j.clay.2010.06.008
Lyons, W.C.; Plisga, G.J.; Lorenz, M.D.: Standard Handbook of Petroleum and Natural Gas Engineering, Chapter 4, 4-1-4-584. Gulf Professional Publishing (2016). https://doi.org/10.1016/B978-0-12-383846-9.00004-7
Mohamed, A.K.; Elkatatny, S.M.; Mahmoud, M.A.; Shawabkeh, R.A.; Al-Majed, A.A.: The evaluation of micronized barite as a weighting material for completing HPHT wells. Paper SPE-183768-MS, Presented at SPE Middle East Oil & Gas Show and Conference, Manama, Kingdom of Bahrain, 6–9 March (2017). https://doi.org/10.2118/183768-MS
Tehrani, A.; Cliffe, A.; Hodder, M.H.; Young, S.; Lee, J.; Stark, J.; Seale, S.: Alternative drilling fluid weighting agents: a com-prehensive study on ilmenite and hematite. Paper SPE-167937-MS, Presented at the IADC/SPE Drilling Conference and Exhibition, Dallas, TX, 4–6 March (2014). https://doi.org/10.2118/167937-MS.
Bern, P.A.; Zamora, M.; Slater, K.S.; Hearn, P.J.: The influence of drilling variables on barite sag. Paper SPE-36670-MS, Presented at SPE Annual Technical Conference and Exhibition, Denver, Colorado, 6–9 October (1996). https://doi.org/10.2118/36670-MS
Bern P.A.; van Oort, E.; Neusstadt, B.; Ebeltoft, H.; Zurdo, C.; Zamora, M.; Slater, K.: Barite sag: measurement, modelling and management. Paper SPE-47784-MS, Presented at IADC/SPE Asia Pacific Drilling Technology, Jakarta, 7–9 September (1998). https://doi.org/10.2118/47784-MS
Amighi, M.R.; Shahbazi, K.: The best common ways to manage barite sag in HPHT and deviated operations with a case study in the Iran oil industry. J. Pet. Sci. Technol. 29(17), 1864–1872 (2011). https://doi.org/10.1080/10916461003662992
Dye, W.; Hemphill, T.; Gusler, W.; Mullen, G.: Correlation of ultra-low shear rate viscosity and dynamic barite sag in invert-emulsion drilling fluids. Paper SPE-56636-MS, Presented at SPE Annual Technical Conference and Exhibition, Houston Texas, 3–6 October (1999). https://doi.org/10.2118/56636-MS
Nguyen, T.; Miska, S.; Yu, M.; Takach, N.; Ahmed, R.; Saasen, A.; Omland, T.H.; Maxey, J.: Experimental study of dynamic barite sag in oil-based drilling fluids using a modified rotational viscometer and a flow loop. J. Pet. Sci. Eng. 78(1), 160–165 (2011). https://doi.org/10.1016/j.petrol.2011.04.018
Basfar, S.; Elkatatny, S.; Mahmoud, M.; Kamal, M.S.; Murtaza, M.; Stanitzek, T.: Prevention of barite sagging while drilling high-pressure high-temperature (HPHT) Wells. Paper SPE-192198-MS, Presented at SPE Kingdom of Saudi Arabia Annual Technical Symposium and Exhibition, Dammam, 23–26 April (2018). https://doi.org/10.2118/192198-MS
Temple, C.; Paterson, A.F.; Leith, C.D.: Method for reducing sag in drilling, completion and workover fluids. U.S. Patent US6861393, (2005)
Davis, C.L.; Livanec, P.W.; Shumway, W.W.: Additive to enhance sag stability of drilling fluid. U.S. Patent Application WO2017188946A1 (2018)
Elkatatny, S.: Mitigation of barite sagging during the drilling of high-pressure high-temperature wells using an invert emulsion drilling fluid. Powder Technol. 352, 325–330 (2019). https://doi.org/10.1016/j.powtec.2019.04.037
Mohamed, A.; Al-Afnan, S.; Elkatatny, S.; Hussein, I.: Prevention of barite sag in water-based drilling fluids by a urea-based additive for drilling deep formations. Sustainability 12(7), 2719 (2020). https://doi.org/10.3390/su12072719
Elkatatny, S.M.; Nasr-El-Din, H.; Al-Bagoury, M.: Evaluation of micronized ilmenite as weighting material in water-based drilling fluids for HPHT applications. Paper SPE-163377-MS, Presented at the SPE Kuwait International Petroleum Conference and Exhibition, Kuwait City, Kuwait, 10–12 December (2012). https://doi.org/10.2118/163377-MS
Al-Bagoury, M.: Micronized Ilmenite-A non-damaging non-sagging new weight material for drilling fluids. Paper SPE-169182-MS, Presented at the SPE Bergen One Day Seminar, Bergen, 2 April (2014). https://doi.org/10.2118/169182-MS
Boyou, N.V.; Ismail, I.; Sulaiman, W.R.; Haddad, A.S.; Husein, N.; Hui, H.T.; Nadaraja, K.: Experimental investigation of hole cleaning in directional drilling by using nano-enhanced water-based drilling fluids. J. Pet. Sci. Eng. 176, 220–231 (2019). https://doi.org/10.1016/j.petrol.2019.01.063
Abdou, M.I.; Al-Sabagh, A.M.; Ahmed, H.E.; Fadl, A.M.: Impact of barite and ilmenite mixture on enhancing the drilling mud weight. Egypt. J. Pet. 4, 955–967 (2018). https://doi.org/10.1016/j.ejpe.2018.02.004
Mohamed, A.; Basfar, S.; Elkatatny, S.; Al-Majed, A.A.: Prevention of barite sag in oil-based drilling fluids using a mixture of barite and ilmenite as weighting material. Sustainability 11, 5617 (2019). https://doi.org/10.3390/su11205617
Basfar, S.; Elkatatny, S.: Prevention of hematite settling using synthetic layered silicate while drilling high-pressure wells. Arab. J. Geosci. 13, 459 (2020). https://doi.org/10.1007/s12517-020-05516-2
Wagle, V.; Al-Yami, A.S.; AlAbdullatif, Z.; Bubshait, A.S.; AlSafran, A.: Mitigation of stuck pipe challenges in HTHP conditions using acid soluble blend of barite and manganese tetroxide as weighting materials for drilling fluids. Paper SPE-175844-MS, Presented at the SPE North Africa Technical Conference and Exhibition, Cairo, 14–16 September (2015). https://doi.org/10.2118/175844-MS
Basfar, S.; Mohamed, A.; Elkatatny, S.; Al-Majed, A.: A combined barite-ilmenite weighting material to prevent barite sag in water-based drilling fluid. Materials 12(12), 1945 (2019). https://doi.org/10.3390/ma12121945
Basfar, S.; Mohamed, A.; Elkatatny, S.: Barite-Micromax mixture, an enhanced weighting agent for the elimination of barite sag in invert emulsion drilling fluids. J. Pet.Explor. Prod. Technol. 10, 2427–2435 (2020). https://doi.org/10.1007/s13202-020-00892-7
Ma, J.; Yu, P.; Xia, B.; An, Y.: Micro-manganese as a weight agent for improving the suspension capability of drilling fluid and the study of its mechanism. RSC Adv. 9(61), 35509–35523 (2019). https://doi.org/10.1039/C9RA07283G
Gholizadeh-Doonechaly, N.; Tahmasbi, K.; Davani, E.: Development of high-performance water-based mud formulation based on amine derivatives. Paper SPE-121228-MS, Presented at SPE International Symposium on Oilfield Chemistry, The Woodlands, Texas, 20–22 April (2009). https://doi.org/10.2118/121228-MS
Mahrous, R.; Vader, R.; Larreal, E.; Navarro, R.; Salmelid, B.; Honey, A.; Weir, M.; Lammers, G.; Rijnen, P.: High performance water-based mud HPWBM: turning old ways into new opportunities. Paper SPE-182286-MS, Presented at SPE Asia Pacific Oil & Gas Conference and Exhibition, Perth, 25–27 October (2016). https://doi.org/10.2118/182286-MS
Addagalla, A.; Maley, I; Lawal, I.; Jadhav, P.; Luigi, M.: Minimum stress, maximum pressure: a new high performance bridging system facilitates drilling depleted formations at high overbalance in middle east. Paper SPE-192051-MS, Presented at SPE Asia Pacific Oil and Gas Conference and Exhibition, Brisbane, 23–25 October (2018). https://doi.org/10.2118/192051-MS
Gomaa, I.; Elkatatny, S.; Abdulraheem, A.: Real-time determination of rheological properties of high over-balanced drilling fluid used for drilling ultra-deep gas wells using artificial neural network. J. Nat. Gas Sci. Eng. 77, 103224 (2020). https://doi.org/10.1016/j.jngse.2020.103224
West, G.; Morales, L.J.: New drilling fluid solution for unconventional sand wells in the San Juan Area. SPE-103036-MS, Presented at Paper SPE Annual Technical Conference and Exhibition, San Antonio, 24–27 September (2006). https://doi.org/10.2118/103036-MS
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Ahmed, A., Alsaihati, A. & Elkatatny, S. An Overview of the Common Water-Based Formulations Used for Drilling Onshore Gas Wells in the Middle East. Arab J Sci Eng 46, 6867–6877 (2021). https://doi.org/10.1007/s13369-020-05107-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13369-020-05107-z