Abstract
A theoretical model for mixed lubrication with more accurate contact length has been developed based on the average volume flow model and asperity flattening model, and the lubricant volume flow rate and outlet speed ratio are determined by integrating differential equations based on rolling parameters. The lubrication characteristics at the roll−strip interface with different surface roughness, rolling speed, reduction and lubricant viscosity are analyzed respectively. Additionally, the average volume flow rates of lubricant under different rolling conditions are calculated and used to explain the change rule of lubrication characteristics. The developed scheme is able to determine the total pressure, lubricant pressure, film thickness and real contact area at any point within the work zone. The prediction and analysis of mixed lubrication characteristics at the interface is meaningful to better control the surface quality and optimize the rolling process.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
KIJIMA H. Influence of lubrication on roughness crushing in skin-pass rolling of steel strip [J]. Journal of Materials Processing Technology, 2015, 216: 1–9.
MORALES ESPEJEL G, BRIZMER V, PIRAS E. Roughness evolution in mixed lubrication condition due to mild wear [J]. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 2015: 1350650115577404.
PATIR N, CHENG H S. An average flow model for determining effects of three-dimensional roughness on partial hydrodynamic lubrication [J]. Journal of Tribology, 1978, 100(1): 12–17.
PELLIZZARI M, CESCATO D, DE FLORA M G. Hot friction and wear behaviour of high speed steel and high chromium iron for rolls [J]. Wear, 2009, 267(1): 467–475.
GARZA-MONTES-DE-OCA N F, RAINFORTH W M. Wear mechanisms experienced by a work roll grade high speed steel under different environmental conditions [J]. Wear, 2009, 267(1): 441–448.
FU Kuo, ZANG Yong, GAO Zhi-ying. Mixed lubrication characteristics of cold rolling process [J]. Journal of Northeastern University, 2014, 35(7): 1005–1010. (in Chinese)
WANG Qiao-yi, ZHANG Ze, CHEN Hui-qin, GUO Shan, ZHAO Jing-wei. Characteristics of unsteady lubrication film in metalforming process with dynamic roll gap [J]. Journal of Central South University, 2014, 21: 3787–3792.
WILSON W R D, SHEU S. Real area of contact and boundary friction in metal forming [J]. International Journal of Mechanical Sciences, 1988, 30(7): 475–489.
WILSON W R D, CHANG D F. Low speed mixed lubrication of bulk metal forming processes [J]. Journal of Tribology, 1996, 118(1): 83–89.
CHANG D F, MARSAULT N, WILSON W R D. Lubrication of strip rolling in the low-speed mixed regime [J]. Tribology Transactions, 1996, 39(2): 407–415.
LIN H S, MARSAULT N, WILSON W R D. A mixed lubrication model for cold strip rolling—Part I: Theoretical [J]. Tribology Transactions, 1998, 41(3): 317–326.
FU K, ZANG Y, GAO Z. Partial film lubrication characteristics of inlet zone in cold strip rolling [J]. Journal of Tribology, 2014, 136(4): 041502.
SUN J, LIU N, XIA L, WU D. Research of oil film thickness model and surface quality in cold rolling copper foil [J]. Lubrication Science, 2014, 26(2): 95–106.
LO S W, YANG T C, LIN H S. The lubricity of oil-in-water emulsion in cold strip rolling process under mixed lubrication [J]. Tribology International, 2013, 66: 125–133.
KOSASIH P, TIEU A K. Mixed film lubrication of strip rolling using O/W emulsions [J]. Tribology International, 2007, 40(5): 709–716.
XIE H, MANABE K I, FURUSHIMA T, TADA K, JIANG Z. Lubrication characterisation analysis of stainless steel foil during micro rolling [J]. The International Journal of Advanced Manufacturing Technology, 2016, 82(1−4): 65–73.
LIU N, SUN J, ZHU Z, XIA L, XIONG S. Research of lubrication model and surface quality in cold-rolling copper alloy using O/W emulsions [J]. Rare Metal Materials and Engineering, 2015, 44(8): 1845–1850.
PATIR N, CHENG H S. Application of average flow model to lubrication between rough sliding surfaces [J]. Journal of Tribology, 1979, 101(2): 220–229.
WU C, ZHENG L. An average reynolds equation for partial film lubrication with a contact factor [J]. Journal of Tribology, 1989, 111(1): 188–191.
YAN S, KURODA S. Lubrication with emulsion: First report, the extended Reynolds equation [J]. Wear, 1997, 206(1): 230–237.
ANTONETTI V, WHITTLE T, SIMONS R. An approximate thermal contact conductance correlation [J]. Journal of Electronic Packaging, 1993, 115(1): 131–134.
SUTCLIFFE M. Surface asperity deformation in metal forming processes [J]. International Journal of Mechanical Sciences, 1988, 30(11): 847–868.
Author information
Authors and Affiliations
Corresponding author
Additional information
Foundation item: Project(2012BAF09B04) supported by the National Key Technology Research and Development Program of China
Rights and permissions
About this article
Cite this article
Wu, Jq., Liang, Xp. & Pan, Fs. Parametric analysis of mixed lubrication characteristics in work zone of strip rolling. J. Cent. South Univ. 23, 3153–3159 (2016). https://doi.org/10.1007/s11771-016-3381-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11771-016-3381-9