Abstract
A miniaturized printed antenna with extended circular patch and partial ground plane for ultra-wideband applications is designed and investigated. The overall structure volume of the antenna is 15 * 20 * 1.6 m3. Proposed antenna’s reflection coefficient (S11 < − 10 dB) is 3.1–20 GHz with the Impedance B/W of 146.3%. The values of the peak gain and antenna efficiency stand at 4.8 dB and 67% respectively, both of which are achieved in the operational frequency band of the design. The suggested antenna with stable far-field pattern satisfies the monopole conditions. The both measured and simulated Co-pol. and (X)-pol. are relatively good agreement. The CST simulator is used to make the proposed structure. The frequency shifted to 3.1 GHz by making a partial ground plane and higher frequency shifted to 20 GHz by introducing a to circular parasitic element is placed in the circular ring slot of the patch. The proposed structure is tested to validate the results of the simulations thus, a good agreement between measured and simulated results is satisfactory that proves the structure’s validity for UWB applications. The proposed antenna finds application in WiMAX-band of 3.5, 5.5 GHz, WLAN-band of 5.2, 5.8 GHz, X-band of 8–12 GHz.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
As per the need of advancements in wireless communication, broadband partial ground plane antenna with compact size will provide several possibilities to the researchers worldwide. Broadband partial ground plane antenna radiator have large bandwidth, high efficiency, high gain, and provide ease of fabrication. A microstrip elliptical slot structure have been attention in the field of UWB band and achieved the ultra-wideband for multiple applications, circular ring in the patch has been reported [1]. Many compact structure have been reported for UWB applications, mentions as circular shaped ring, circular slot and L-shaped slots, cutting rectangular, printed curved slot, triangular, U-shaped, semi-circular slot, in [2,3,4,5]. Bandwidth enhancement is reported by S-slot rectangular patch [6]. Wideband antenna achieved 4.5 dB gain due to truncation in the circular model [7]. Broadband behaviour have been proposed due to cutting; triangular, U-shaped rectangular and L-shaped slots [8, 9]. Dual-frequency ranges are observed by the added parasitic slot in the patch, by adding circles in the back side plane [10, 11]. 44% fractional bandwidth has been obtained by applying fractal slot in circular patch [12]. Enhanced bandwidth with dual frequency by introduced gap coupling (technique) have been reported in [13]. To achieve broadside radiation-pattern by sweeping of ‘E’-shaped element in radiator has been suggested [14]. A ladder-shaped structures in the back plane resulting increased wide band resonance as reported in [15]. By using rubber as a substrate, ultra-wide band has been reported [16]. Ultra-wide band applications has been achieved due to create multi-slots in the planar antenna [17]. By creating small fractal element in planar antenna, bandwidth enhancement is reported [18]. Low order frequency modes is observed by making defective ground structure [19]. UWB applications have been reported due to; rectangular parasitic patches near to the stripline, modified patch with defective back plane, miniaturized antenna with printed ground plane and dumbbell shaped planar structure [20,21,22]. Lower side frequency is excited due to a defective backplane, higher side frequency is excited by added a rectangular-shaped parasitic element in circular patch [23].
Bandwidth enhancement, in this case, is achieved in the lower frequency band due to impedance matching. The comparison analysis of earlier published monopole designs are mention in Table 1. It is noticed that the presented antenna exhibits UWB behavior (3.1–20 GHz) and impedance bandwidth of 146% in a very small size of 300 mm2. A miniaturized printed design with an extended circular patch and the incomplete ground plane is proposed in this paper. Bandwidth expands at the higher and lower frequencies because of the higher order and lower order modes. This fulfils the dual purpose of bandwidth enhancement and miniaturization. Most of the structures reported above are complex in nature and have a larger dimension (typically of the size of 27 * 24 * 1.6 mm3). In this article, a compact antenna (15 * 20 * 1.6 mm3) with very large impedance B/W is reported which is having a four-stages. Antenna’s all stages is unique and represents the different simulation (S11) results. The suggested design is represented by stage 04. The higher-modes resonances are created by introduced the incomplete ground plane whereas the lower-modes resonances are achieved by extended circular patch. The following sections are discussed in this article: In Sect. 2, the optimum dimension of the suggested design with all parameters, 04-stages evolution, and variations in return loss results due to the change in the stages, various important parametric parameters studies are taken up. In Sect. 3, the relative analysis of the (S11) measured curve and (S11) simulated curve, simulated I/P impedance curve, measured and simulated far-field pattern, simulated of gain, and antenna efficiency, analysis of antenna’s surface current is presented.
2 Antenna Geometry, Evolution and Parameter Study
The FR4 substrate is used to fabricate the suggested design. The specification of the flame retardant (FR4) material is 4.4 permittivity, 1.6 mm thick and a loss tangent equal to 0.025 with physical volume of 15 * 20 * 1.6 mm3 and antenna is fed by a 50 Ω line. The suggested design’s geometry with optimum parameters is shown in Fig. 1. Circular patch, circular slot and parasitic circular element with microstrip line makes a front view of the suggested antenna. The diameter of the circular patch is denoted by ‘c’, ‘d’ represents the slot diameter, ‘e’ represents the parasitic element diameter and ‘w’ represents the width of the microstrip line.
The backside of the design has a partial ground plane with semi-circular slot, where ‘p’ is a diameter of semi-circular slot, ‘k * q’ represents the area of ladder pattern element, ‘i’ represents the upper plane height and other elements in the back plane is represented by ‘r * k’, ‘j’, ‘m * n’, ‘f’, ‘w’, and ‘o’. ‘b’ represents the complete length and ‘a’ represents the complete breadth of the design. ‘h’ denotes the thickness of the assigned substrate. Table 2 shows the parameter values (reported in mm) of the design.
The evolution of the presented design in various stages have been presented in Fig. 2. Stage 01 shows the circular-shaped patch and an incomplete ground plane with microstrip line. Stage 02 shows the unique design in the backside with semi-circular slot and multiple rectangular designs are introduced causes excitation of higher frequency. Stage 03 shows that better resonance is observed by introduced a circular slot in the main patch with the same backplane. Stage 04 is the proposed antenna design, by adding parasitic circular-shaped element in the main patch causes impedance matching and resonances in lower and higher frequencies are excited.
Proposed design development from stage 01 to stage 04 along with their respective reflection coefficient (S11) is shown in Fig. 3. The first stage (stage 01) has a defined ground plane and simple circular patch. The operating bandwidth for this stage is from 3.5 to 6.2 GHz and 8 to 12 GHz. The second stage is having a (PGP) partial ground plane and a simple circular patch. The operating bandwidth for this stage is from 2.8 to 3.3 GHz, 3.8 to 6.5 GHz and 7.5 to 20 GHz. In this stage the antenna covers three distinctive frequency bands. The third stage is having an additional slot in the main patch, with operating bandwidth is from 3.2 to 7.2 GHz and 8 to 20 GHz. The frequency shifted to 3.1 GHz by making a partial ground plane, and higher frequency shifted to 20 GHz by introducing a circular parasitic element is placed in the circular ring, as visible in the final stage (stage 04).
In the parameter study section, the variation of four parameters and optimized the result on this basis by observing their effects on S-parameter results. Firstly, the parameter (c) is sweeping from 12 to 15 mm, change the diameter, resulting in a change in results. When ‘c’ is < 14 mm multiband occurs after 6 GHz. The proper impedance matching is obtained in the UWB band at an optimum value of 14 mm size as shown in Fig. 4. When the size of the circular slot (d) is increased from 9 to 11 mm, it gives different result at different size, when‘d’ is less than 10 mm size entire band mismatched, lower order oscillations visible at optimum value of 10 mm and it shows the full impedance matching as shown in Fig. 5. Another parameter (e) is sweeping from 4 to 7 mm and it provide return loss (S11 < −10 dB) at optimum value of 6 mm. This parameter is very important because it provides lower band impedance matching which shown in Fig. 6. Figure 7 shows parametric study of semi-circular slot (p), the parameter ‘p’ are varied from 5 to 7 mm and optimum results are obtained at 6 mm due to perfect impedance matching at this dimension. The final proposed antenna exhibits an overall fractional bandwidth greater than 146.3%. Results are discussed and elaborated in the next section.
3 Results and Discussion
The presented extended circular patch antenna has an extremely compact structure of 300 mm2. The proposed antenna is a low profile ultra-wideband (UWB) antenna, therefore it could be useful for multiple applications. Drafting of the suggested design and all results are simulated using CST Tool. The fabrication of the suggested design is manufactured on substrate (FR4) using LPKF ProtoMat E-44 milling machine.
Figure 8 shows the testing setup of the suggested design in anechoic chamber. Proposed antenna testing is conducted by using VNA (Agilent) and the microstrip line is connected with 50 Ω (SMA) connector inside an anechoic chamber.
Figure 9 shows the relative analysis of the measured (S11) curve and simulated (S11) curve for the suggested design. The graph shows measured (S11) curve result are in good acceptance with the simulated (S11) result. The small deviation arises in some frequencies because the size of the suggested design is compact and 50 Ω SMA A-type connector is comparably big which accounts for the manufactured tolerances.
Figure 10 shows I/P impedance curve which represents the simulated real and imaginary components versus the frequency curve for the suggested design. The real impedance is sustained at 50 Ω throughout the proposed band and shows optimum impedance matching. The imaginary impedance shows the behavior of the antenna, initially it behaves like inductive (due to +ve polarity from 3.1 to 3.6 GHz), and after that antenna shows capacitive behavior (due to −ve polarity from 3.6 to 10 GHz) and again it further fluctuates to inductive or capacitive behaviour’s at higher frequencies as shown in Fig. 10.
Figure 11 shows simulated antenna efficiency and gain versus frequency curve of the suggested design. Peak gain is observed at 16.2 GHz with a value of 4.8 dB. The peak radiation efficiency is observed at 14.4 GHz with a value of 67%, as frequency increases losses increase causes the antenna efficiency becomes decreases at higher frequency.
Figures 12 and 13 shows the comparative analysis of measured and simulated Co. and (X)-pol. at four selected frequencies. The H-polar pattern is defined by XoZ-plane, Φ = 0° and E-polar pattern by YoZ- plane, Φ = 90°. Polar pattern of Co/(X)-pol. of H and E-plane at (3.3 and 6 GHz resonance) is shown in Fig. 12. The stable Co-pol. Omni and bi-directional polar pattern is observed with a good agreement of (X)-pol. at the lower frequency modes, whereas at (8.8 and 16 GHz frequencies) is shown in Fig. 13. The distorted occurs at higher frequencies due to the fact that ohmic losses increase.
Antenna’s surface current (front view) is visible in Fig. 14 at a constant phase (178°) for selected 04 frequencies. As evident from Fig. 14; I and II at (3.3 and 6 GHz frequencies) as the current signal strength is higher with the high current value of 167 and 61.7 A/m and in Fig. 14; III and IV at (8.8 and 16 GHz frequencies) the current signal strength is higher with the high value of 171 and 82.4 A/m. Mainly current strength due to the surface of the main circular patch, circular slot and circular parasitic element as well as due to ladder structure in partial ground plane.
4 Conclusion
A miniaturized antenna with extended circular patch and partial ground plane is proposed. A suggested antenna has been designed, fabricated and investigated. The impedance bandwidth (S11 < − 10 dB) is 146% running from 3.1 to 20 GHz with a size of 300 mm2. Antenna’s peak gain is 4.8 dB and antenna efficiency is 67% have been obtained. The suggested design exhibits stable polar pattern (H-plane with omni-directional at Φ = 0°) and (E-plane with Bi-directional at Φ = 90°). The surface current shows good signal strength at (3.3, 6, 8.8, and 16 GHz frequencies). All above properties show that the presented structure is useful for broadband applications which includes 3.5/5.5 GHz (WiMAX), 5.2/5.8 GHz (WLAN), 8–12 GHz (X-band), the field of satellite communication and numerous other wireless uses.
References
Ahirwar, D., Shrivastava, A., & Baudha, S. (2016). A decagon shaped universal compact broadband printed monopole antenna. Microwave and Optical Technology Letters, 58, 2760–2764.
Azim, R., Islam, M. T., & Misran, N. (2010). Printed circular ring antenna for UWB application. In IEEE, 6th international conference on electrical and computer engineering, ICECE (pp. 361–363).
Li, G., Zhai, H., Li, T., & Liang, C. (2012). A compact antenna with broad bandwidth and quad-sense circular polarization. IEEE Antennas and Wireless Propagation Letters, 11, 791–794.
Telsang, T. M., & Kakade, A. B. (2014). Ultra-wideband slotted semi-circular patch antenna. Microwave and Optical Technology Letters, 56, 362–369.
Baudha, S., & Vishwakarma, D. K. (2014). Miniaturized dual broadband printed slot antenna with parasitic slot and patch. Microwave and Optical Technology Letters, 56, 2260–2265.
Aneesh, M., Ansari, J. A., Singh, A., & Sayeed, S. S. (2013). Analysis of S-shape microstrip patch antenna for bluetooth applications. International Journal of Scientific and Research Publications, 3(11), 1–4.
Kurniawan, A., & Mukhlishin, S. (2013). Wideband Antenna Design and Fabrication for Modern Wireless Communications Systems. Procedia Technology, 11, 348–353.
Khidre, A., Lee, K. F., Elsherbeni, A. Z., & Yang, F. (2013). Wideband dual-beam U-slot microstrip antenna. IEEE Transactions on Antennas and Propagation, 61(3), 1415–1418.
Pflaum, S., Thuc, P. L., Kossiavas, G., & Staraj, R. (2013). Performance enhancement of a circularly polarized patch antenna for radio frequency identification readers using an electromagnetic band-gap ground plane. Microwave and Optical Technology Letters., 55, 1599–1602.
Ghosh, A., Ghosh, S. K., Ghosh, D., & Chattopadhyay, S. (2014). Improved polarization purity for circular microstrip antenna with defected patch surface. International Journal of Microwave and Wireless Technologies, 8, 89.
Baudha, S., Goswami, A. K., & Yadav, M. V. (2019). Miniaturized dual-band antenna with a rectangular patch and symmetrically placed circles in the partial ground plane. Progress in Electromagnetics Research, 78, 29–37.
Gupta, H. K., Singhal, P. K., Sharma, P. K., & Jadon, V. K. (2012). Slotted circular microstrip patch antenna designs for multiband application in wireless communication. International Journal of Engineering and Technology, 3, 158–167.
Pal, S., Das, G. K., & Mitra, M. (2011). Gap-coupled microstrip antennas for dual frequency operations. International Journal of Engineering, Science and Technology, 3(8), 6149–6152.
Deshmukh, A. A., Singh, D., & Zaveri, P. (2016). Broadband slot cut rectangular microstrip antenna. Procedia Computer Science, 93, 53–59.
Baudha, S., & Vishwakarma, D. K. (2018). A compact broadband printed circular slot antenna with stair shaped ground plane. Progress in Electromagnetics Research Letters, 74, 9–16.
Lakshmanan, R., & Sukumaran, S. K. (2016). Flexible ultra wide band antenna for WBAN applications. Procedia Technology, 24, 880–887.
Awad, N. M., & Abdelazeez, M. K. (2018). Multi-slot microstrip antenna for ultra-wide band applications. Journal of King Saud University Engineering Sciences, 30, 38–45.
Fallahi, H., & Atlasbaf, Z. (2015). Bandwidth enhancement of a CPW-fed monopole antenna with small fractal elements. AEU, International Journal of Electronics and Communication, 69, 590–595.
Chakraborty, M., Rana, B., Sarkar, P. P., & Das, A. (2012). Design and analysis of a compact rectangular microstrip antenna with slots using defective ground structure. Procedia Technology, 4, 411–416.
Baudha, S., & Yadav, M. V. (2019). A novel design of a planar antenna with modified patch and defective ground plane for ultra-wideband applications. Microwave and Optical Technology Letters, 61, 1320–1327.
Yadav, M. V., & Baudha, S. (2019). A compact ultra-wide band planar antenna with corrugated ladder ground plane for multiple applications. Microwave and Optical Technology Letters, 61, 1341–1348.
Garg, H., Baudha, S., & Yadav, M. V. (2019). Dumbbell shaped microstrip broadband antenna. Journal of Microwaves, Optoelectronics and Electromagnetic Applications, 18, 33–41.
Hota, S., Baudha, S., Mangaraj, B. B., & Yadav, M. V. (2019). A compact, ultrawide band planar antenna with modified circular patch and a defective ground plane for multiple applications. Microwave and Optical Technology Letters, 61(9), 2088–2097.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Yadav, M.V., Baudha, S. A Miniaturized Printed Antenna with Extended Circular Patch and Partial Ground Plane for UWB Applications. Wireless Pers Commun 116, 311–323 (2021). https://doi.org/10.1007/s11277-020-07716-1
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11277-020-07716-1