A method for producing strips by titanium powder rolling is proposed. The effect from powder annealing on the porosity of the initial billet is analyzed. The optimal temperatures of sintering and annealing after intermediate rolling are determined. It is shown that, under the optimal deformation conditions, the strip has mechanical properties that compare well with those of strips produced conventionally.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
E. M. Borisovskaya, V. A. Nazarenko, Yu. M. Podrezov, et al., “Mechanical properties of powder titanium at different production stages. I. Densification curves for titanium powder billets,” Powder Metall. Met. Ceram., 47, No. 7–8, 406–413 (2008).
E. M. Borisovskaya, V. A. Nazarenko, Yu. M. Podrezov, et al., “Mechanical properties of powder titanium at different production stages. ІІ. Mechanical behavior of porous titanium compacts,” Powder Metall. Met. Ceram., 47, No. 9–10, 538–545 (2008).
Yu. M. Podrezov, V. A. Nazarenko, Ya. I. Evich, and A. V. Vdovichenko, “Mechanical properties of powder titanium at different production stages. III. Contact formation in powder titanium based on examination of mechanical properties in sintering,” Powder Metall. Met. Ceram., 48, No. 3–4, 201–210 (2009).
Yu. M. Podrezov, V. A. Nazarenko, A. V. Laptev, et al., “Mechanical properties of powder titanium at different production stages. IV. Mechanical properties and contact formation in powder titanium produced by dynamic hot pressing,” Powder Metall. Met. Ceram., 48, No. 5–6, 295–301 (2009).
R. K. Dube, Powder Metallurgy, 12, No. 1, 22–24 (1980).
F. H. Froes and J. E. Smugeresky (eds.), Powder Metallurgy of Titanium Alloys: Proceedings, Metallurgical Society of AIME, Warrendale, Pennsylvania (1980).
E. B. Lozhechnikov, Rolling in Powder Metallurgy [in Russian], Metallurgiya, Moscow (1987), p. 184.
G. A. Vinogradov and V. P. Katashinskii, Theory of Sheet Rolling of Metal Powders and Granules [in Russian], Metallurgiya, Moscow (1979), p. 224.
G. A. Vinogradov, Yu. N. Semenov, O. A. Katrus, and V. P. Katashinskii, Rolling of Metal Powders [in Russian], Metallurgiya, Moscow (1969), p. 382.
R. K. Dube, Int. Mater. Reviews, 35, No. 5, 253–291 (1990).
M. V. Mal’tsev, V. G. Khromov, and Z. N. Malyshkina, “Research into production and properties of electrolytic metal ceramic titanium,” Tr. Gor’kov. Politekh. Inst., Vol. 26, Issue 15 (1970).
L. S. Shmelev and V. K. Sorokin, “Industrial production of sheet titanium by powder rolling,” Tsvet. Metally, No. 10, 49–50 (1993).
V. A. Ponomarev, V. S. Khozikov, and Yu. S. Get’manskii, “Production of molybdenum–copper pseudoalloys by powder rolling,” Élektron. Tekh., Ser. Tekhnol. Org. Proizv. Oborud., Issue 4, 128–132 (1974).
V. A. Ponomarev, L. S. Shmelev, and V. S. Khozikov, “Implementation of the powder rolling process for producing strips from molybdenum–copper pseudoalloys,” Poroshk. Metall., No. 3, 101–103 (1981).
M. A. Baek, “Production of dispersion-strengthened nickel strips by powder rolling,” in: Proc. Sci.-Tekh. Conf., Kuibyshev Aviats. Univ., Kuibyshev (1970), Part 3.
M. A. Baek, “Research into the rolling of strips from powders of dispersion-strengthened nickel and copper,” in: Proc. 6th Repub. Seminar on Powder Metallurgy [in Russian], Tallinn (1979).
V. G. Khromov, Research into the Rolling of Powders and Thermal Treatment in Production of a Titanium Strip [in Russian], Author’s Abstract of PhD Thesis, Gorkii (1964).
V. G. Khromov, “Producing high-plastic titanium by powder rolling,” in: Proc. Interacadem. Sci.-Tekh. Conf. on Powder Metallurgy [in Russian], Kuibyshev (1963).
M. D. Ayers, Industrial Heating, 41, No. 9, 22–25 (1974).
R. P. Irving, Iron Age, 224 (1981).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Poroshkovaya Metallurgiya, Vol. 48, No. 11–12 (470), pp. 51–60, 2009.
Rights and permissions
About this article
Cite this article
Gogaev, K.A., Nazarenko, V.A., Voropaev, V.A. et al. Mechanical properties of powder titanium at different production stages. V. Properties of a titanium strip produced by powder rolling. Powder Metall Met Ceram 48, 652–658 (2009). https://doi.org/10.1007/s11106-010-9182-z
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11106-010-9182-z