Abstract
Monodisperse micro-sized liquid metal droplets have received considerable attention for developing flexible electronics, microfluidics actuators and reconfigurable devices. Herein we report an innovative and efficient strategy for large-scale preparation of Galinstan liquid metal microdroplets with controllable sizes using a micro-needle induced glass capillary microfluidic device. By inserting a stainless steel micro-needle into the inner liquid metal phase in the glass capillary, the hydrodynamic instability of the liquid metal stream is significantly suppressed to guarantee steady fluid flow before the liquid metal is pinched off by the outer phase flow, giving rise to a stable generation of monodisperse liquid metal microdroplets. The microdroplet size dependence on the flow ratio of the continuous and dispersed-phase is investigated experimentally. A theoretical framework based on the Plateau–Rayleigh instability is proposed to explain the advantage of the micro-needle induced strategy. This strategy has great potential for the generation of high interfacial tension liquid metal emulsions.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
1 Introduction
Combined with fascinating metallic characteristics and fluidic properties, such as large surface tension, high electrical and thermal conductivities, low viscosity, and significant deformability, room temperature liquid metals have received considerable research interest recently. In contrast to mercury, low melting point gallium based eutectic liquid metals such as EGaIn (75% gallium, 25% indium) and Galinstan (68.5% gallium, 21.5% indium, and 10% tin) are being increasingly investigated by research community in laboratories for its negligible vapour pressure and nontoxicity (Chiechi et al. 2008; Hu et al. 2017; Shay et al. 2018). These remarkable physicochemical properties enable gallium-based liquid metals great promise for a variety of practical application including fluidic actuators (Tang et al. 2015, 2014a, b), electrochemical sensors (Wei et al. 2014), optical and electrical switches (Sen and Chang-Jin 2009; Wissman et al. 2017; Yoo et al. 2011), reconfigurable/stretchable electronics (Cheng et al. 2009; Dickey 2017; Liang et al. 2017), and biomedicine (Lu et al. 2015). Particularly, the growing trends in the miniaturization of microfluidic reaction engineering and the development of lab-on-a-chip analysis for their flexible integration into microfluidics have facilitated the expansion of micro and nano-sized liquid metal droplets demand from the traditional polydispersed emulsions to precision monodispersity.
To date, there are several approaches have been exploited for producing micro-sized liquid metal droplets, including molding (Mohammed et al. 2014), acoustic wave (Tang et al. 2016), sonication (Hohman et al. 2011; Lu et al. 2015), stream jetting (Yu et al. 2014), electro-hydrodynamic shooting (Fang et al. 2014), and microfluidic flow focusing (Gol et al. 2016; Thelen et al. 2012). With good rheological properties, the replica molding technique featured by spreading liquid metal across the elastomeric patterned cylindrical reservoirs was demonstrated to create microspheres (Mohammed et al. 2014). Although the replication method is simple, the demand of mass production limits its pervasive application. Another commonly encountered and efficient option for large-scale microdroplet production is sonication dispersion method (Lu et al. 2015), which exploits ultrasonic wave to fabricate liquid metal marble spheres in a nonsolvent for different durations. Despite the advantages of the sonication technique for microdroplet formation, this approach suffers from a drawback that the liquid metal droplet diameter is commonly with a wide size distribution, ranging from dozens of nanometers to several micrometers. Additionally, the acoustic wave-induced-forces were introduced to generate EGaIn microdroplets with controllable size by tuning the interfacial tension of the liquid metal with either electrochemistry or electrocapillary accompanied with an electrical potential. Whereas the acoustic wave generation equipment is relatively high-cost consumption and the droplet production platform is complex. To solve the aforementioned limitations, the special microfluidic flow-focusing method has been extensively investigated to improve the reproducibility and the uniformity of the liquid metal microspheres. It is typically demonstrated by designing a PDMS microfluidic system with a cross-like microchannel configuration and producing microdroplets by adjusting the shear rate or interfacial tension of the two adjacent insoluble streams. The main problem with this approach is the hydrodynamic instability for the droplet formation, caused by the high pressure drop and the corresponding high shear rate within the microchannel. On the other hand, the swelling of PDMS-based microchannel in most organic solvents may sometimes disrupt the micrometer-sized features and make it not so easy to maintain a good uniformity of the liquid metal microdroplets. Whereas the formation of the highly monodisperse bulk liquid metal emulsions is the central technical issue in some occasions. To achieve this goal, a potential strategy is to exploit the glass capillary microfluidic approach (Hou et al. 2017; Jia et al. 2018; Lee and Weitz 2008; Shah et al. 2008; Shum et al. 2008), which has competitive advantage on precise control over the size distribution of microdroplet. However, owing to its extraordinary large surface tension, stable generation of monodispersed liquid metal micro-droplet emulsion is challenging with the conventional co-flow capillary microfluidic device. Consequently, it is still of great importance to explore novel and simple methods for large-scale preparation of liquid metal microdroplets with high interfacial tension.
In this technical innovation, we introduce a novel strategy to achieve highly monodispersed microspherical Galinstan liquid metal with controllable size, by simply inserting a metallic micro-needle into the inner fluid phase of the co-flowing glass capillary device (Fig. 1d, e). In the commonly used co-flowing device (as shown in Fig. 1a, b), due to the high surface tension of the liquid metal and its weak wettability on the glass wall (Davis and Ndao 2018), the inner stream will easily break up even before flowing out of the small aperture. A specific advantage of the new design (Fig. 1d, e) is that the micro-needle can induce significant viscous effect to overcome the hydrodynamic instability of the liquid metal stream when the inner phase is pinched off by the continuous phase. To control the droplet size, a series of experiments are conducted with different flow rate ratios of continuous phase to the dispersed phase, i.e., φ = Qc/Qd. This strategy provides a significant guide for the large-scale production of size-controllable monodisperse liquid metal with high surface tension in laminar flow.
2 Experimental setup
2.1 Materials
Metallic micro-needle with a diameter of 70 µm is adopted (Zongsheng, Harbin, China). Glycerol is purchased from Aladdin. Poly(vinyl alcohol) (PVA, 87–89% hydrolyzed, average Mw = 13,000 − 23,000) and galinstan liquid metal are obtained from Sigma-Aldrich. As the out phase, a mixture of glycerol and 5% PVA aqueous solution with the weight ratio 10:2.9 is used. The inner phase is the bulk galinstan liquid metal.
2.2 Fabrication of glass capillary microfluidic device within inserted micro-needle
As illustrated in Fig. 1a, d, the glass microcapillary chip consisting of coaxial assemblies of round and square glass capillaries on glass slides is utilized to prepare the liquid metal droplets. The two cylindrical capillaries (inner diameter (ID) 0.58 mm, outer diameter (OD) 1.03 mm, World precision instruments, Inc., 1B100-6) are tapered to the desired sizes using a micropipette puller (P-97, Sutter Instrument) and a microforge (MF-900, Narishige, Tritech Research, Inc). The inner diameters of tapered orifices of the capillaries for the inner phase and for final emulsions collection are 100 µm and 200 µm, respectively. Then these tapered capillaries, one with smaller orifice diameter being injection tube and the other being collection tube, are coaxially assembled in the opposite ends of the square capillary (AIT Glass, Inc., 810-9917) with axial spacing of 100 µm. To demonstrate our novel strategy, a micro-needle is assembled into the microfluidic device to stabilize the generation process of liquid metal droplets. We utilize a properly treated 1Cr18Ni19Ti stainless steel micro-needle with a diameter of 70 µm as the micro needle, which is coxially inserted into the inner phase capillary and maintain a distance of about 175 µm between the adjacent ends of the micro-needle and injection tube (as shown in Fig. 1e). As the oil film exiting on the needle surface may intervene the interface contact between the micro-needle and the inner phase liquid metal, we first rinsed the micro-needle with acetone and then dropped it in an alcohol solution to remove oil layer by ultrasonic method to ensure direct contact. Finally, a transparent epoxy resin (Devcon 5 min Epoxy) is used to seal all tubes and micro-needle when necessary. No surface modification of the capillaries and the micro-needle is necessary during the flow focusing, which reduces the experimental variability.
2.3 Micro-needle induced microfluidic fabrication of liquid metal droplets
To generate the liquid metal droplets, we utilize the bulk galinstan liquid metal and an aqueous solution containing a 10:2.9 by weight ratio mixture of glycerol and PVA solution as disperse phase and continuous phase, respectively. The PVA is chosen as a surfactant to be added into the glycerol aqueous solution to prevent droplets against spontaneous coalescence. Two glass syringes (Hamilton) containing two different phases are installed onto syringe pumps (Harvard Apparatus) and connected to the corresponding inlets of the device. And then the inner and out phases are injected into the glass device at a constant flow rate through the injection tube and the interstice between the injection tube and square capillary, respectively. Instead of forming a spherical droplet on the glass substrate with a large contact angle, Galinstan amalgamates metals on the metal surface (Tang et al. 2014b). When pairs of immiscible fluids simultaneously flow across the capillary tip, by carefully adjusting the flowrates of each phase, droplets can be created as the less viscous liquid metal is pinched off by the highly viscous glycerol aqueous solutions. A series of experiments show that the flow rates for relatively steady droplets production to be 5–15 µl/min for Galinstan and 100–1800 µl/min for the glycerol solution.
3 Results and discussion
3.1 Restriction of the Plateau–Rayleigh instability by micro-needle-induced viscous effect
The liquid metal manifests very weak wettability on the glass surface, while the outer phase aqueous solution is easiy to wet the glass surface. Therefore, in the inner capillary, the liquid metal interface will destabilize spontaneously under a small perturbation. When there is no micro-needle involved, the development of the perturbation can be approximately described by the Plateau–Rayleigh (P–R) instability. This theory results in a characteristic time of the instability τ0 = (ρR3/γ)1/2, determined by the equilibrium between the streamwise flow ρR/τ02 and the capillary effect γ/R2. Here, R, ρ, and γ are the radius, density, and surface tension of the liquid metal jet stream.
However, the flow dynamics is obviously different when a micro-needle is introduced. The viscous effect is increased dramatically due to the friction of the needle surface and the corresponding enhancement of the shear rate in the inner phase flow. The situation when the micro-needle with radius r is introduced is illustrated in Fig. 2.
Now assuming the perturbation profile of the liquid metal jet is e = e0 + Δecos(x/λ), the Laplace equation expresses the capillary pressure across the interface:
According to the Poiseuille equation the \(Q=\frac{G}{{12\mu }}\frac{{\Delta p}}{{\Delta x}}\), where µ = 0.002 Pa s is the viscosity of the liquid metal (Sivan et al. 2013), and G is the geometry parameter describing the flow, we obtain the flow rate equation:
where R ≈ e + r. The conservation of the mass requires \(\frac{\partial Q}{\partial x}= - \frac{\partial e}{\partial t}\), which leads to the following equation by substituting (2) and e = e0 + Δecos(x/λ):
Equation (3) indicates the existence of a critical perturbation wavelength λc = R, below which the perturbation will grow as ∂Δe/∂t > 0. We emphasize that this result is consistent with the traditional P–R instability analysis.
Furthermore, Eq. (3) implicitly introduces the characteristic time of the instability τneedle. Considering the influence of the contraction section of the inner phase capillary, we obtain the expression of τneedle:
where δ is the average thickness of the liquid metal stream, δ = (R(x1) + R(x2) − 2r)/2, R(x1) and R(x2) are the inner radiuses of the tapered end on the different sides. L is tapered-end’s length of the injection tube.
The stability of liquid metal droplet generation is closely related to the characteristic time of the P–R instability. Specifically, a longer characteristic time indicates a more stable generation performance. To demonstrate the significantly enhanced stability of droplet formation in the proposed design, the time ratio ξτ = τneedle/τ0 is defined as follow:
Substituting the parameters based on the experimental values: γ = 0.534 N/m (Gol et al. 2015), R = 290 µm, L ≈ 3 mm, δ ≈ 100 µm, we can calculate that ξτ is about 251.84. Therefore, the needle-induced viscous effect can increase the characteristic time of instability up to two orders of magnitude. Our novel microfluidic flow focusing device with the micro-needle can work much more stable and the droplet generation is only determined by the pinch-off process excluding the influence of the instability.
3.2 The effect of micro-needle on liquid metal droplet generation
To verify the function of the micro-needle in the liquid metal droplet formation, we carry out the large-scale microdroplets generation in the hydrodynamic focusing microfluidic device without and with a metal needle. The flowrates for the dispersed and continuous phase are maintained at 10 µl/min and 300 µl/min, respectively, i.e., φ = 30. As the capillary effect is dominant in this microsystem, the contact angle and interfacial tension play key roles in droplet formation. As illustrated in Fig. 1a, when there is no micro-needle in the inner phase capillary, the droplets generation process appears to be unstable, rendering a cluster of highly ununiform droplets jetting from the nozzle in 0.5 ms, and then the liquid metal retracted back toward the inner capillary (Fig. 1c, Movie S1, ESI†). After a few seconds interval during the liquid metal re-fills the inner capillary, the droplet formation repeats the aforementioned process. One of the possible reasons is attributed to the weak surface wettability between the liquid metal and the glass wall. It can also be ascribed to the fluidic self-perturbance occurs when the liquid metal is cutting off due to the combination of the high interfacial tension and the existence of oxidation film on the liquid metal surface, which causes further unevenness in the diameters of the droplets (Fig. 3a). While with the micro-needle inside the inner phase capillary, the Galinstan microdroplets can be generated steadily and periodically with the identical droplet gap (Fig. 1f, Movie S2, ESI†). As the Galinstan liquid metal is injected along the embedded micro-needle, a large number of droplets with uniform size-distribution can be quickly fabricated (Fig. 3c). The unstable process occurring in the experiment without using the needle is never observed here. The liquid metal wets the micro-needle easily because of their similar hydrophilic properties, and thus maintain the minimal total interfacial energies of the inner phase. In particular, as we explain later, the significant improvement of the new setup is attributed to the viscous effect induced by the needle. To quantify the dimensional homogeneity of the droplet, the histograms displaying the diameter distribution for the above two approaches are shown in Fig. 3b, d. It can be found that the average droplet diameter for the conventional capillary device and the new proposed strategy are approximately 181 µm and 168 µm, respectively. While the variance of the droplet diameter normal distribution for the novel approach is 2.19, which is much smaller than the conventional droplet production method 18.03, testifying that the micro-needle induced generation approach has greater potential to produce homogeneous high interfacial tension droplet.
To demonstrate the effect of surface wettability for micro-needle on the droplet generation process, we then construct the micro-needle induced co-flowing microfluidic device with round glass rod having the identical diameter as metallic micro-needle in the inner phase capillary. As expected, with a round glass rod induced method, the liquid metal cannot flow out smoothly with lower flowrate ratio of the continuous phase to the disperse phase as φ = 30, exhibiting congestion phenomenon and a cluster of liquid metal suddenly appearing in the vicinity of the capillary tip. The small droplets are formed at a higher rate with nonperiodic breakup, when the internal flow and external phase flow velocity are maintained at 10 µl/min and 300 µl/min, respectively. Simultaneously, the continuously phase eventually flowed into the inlet capillary, forcing the liquid metal to regress back into the inlet channel and giving rise to the generation of satellite droplets (Fig. 3e). Compared with the normal distribution of the droplet diameter for the above two approaches (Fig. 3d, f), it can be clearly seen that the droplets produced with the metal needle have much better uniformity. Since Galinstan liquid metal has more similar material properties with the metallic micro-needle than the glass, which may give better wettability performance for droplet movement and adsorption on a microfiber media (Fang et al. 2015; Jamali et al. 2018; Manzo et al. 2016). Therefore, it can be probably attributed to the better wettability between the liquid metal and the metallic micro-needle than with the glass capillary, which greatly affects the stability of droplet formation.
The unstable breakup without the presence of the micro-needle reported above can be explained under the theoretical framework of the Plateau–Rayleigh instability (the Reynolds number Re = ρvd/µ ~ O(1), ρ is the density of liquid metal, v is the average flow rate, d is the equivalent diameter). This becomes a serious problem because of the very high surface tension (σ = 0.534 N/m, one order of magnitude larger than water, and the capillary number Ca = ρv/γ ~ O(10− 6), γ is the surface tension) of the liquid metal and the very weak wettability of the liquid metal on the glass wall. Considering the inner phase liquid metal as a cylindrical liquid jet, the characteristic time of the instability is approximately τ0 = (ρR3/γ)1/2 (de Gennes et al. 2004), which is only about 0.3 ms. This value explains the reason of the rapid breakup of the liquid metal within about 0.5 ms that generates a cluster of nonuniform droplets after being pinched off by the outer phase flow. However, the flow dynamics is obviously different when a micro-needle is introduced. The viscous effect is increased dramatically due to the friction of the needle surface and the corresponding enhancement of the shear rate in the inner phase flow. We have performed a theoretical deduction to show that the needle-induced viscous effect can increase the characteristic time of instability τneedle up to two orders of magnitude, i.e., approximately 0.1 s. Therefore, the microfluidic flow focusing device with a micro-needle can work much more stable and the droplet generation is only determined by the pinch-off process excluding the influence of the instability. Nonetheless, the weak wettability of the glass rod surface introduces additional fluctuation of the interface of the metal liquid stream near the rod, which will disrupt the stream and cause the generation of polydisperse microdroplets.
3.3 The effect of flowrates ratios on liquid metal droplet diameter
To demonstrate the flexibility of our newly proposed metallic micro-needle induced approach, we controllably fabricate the Galinstan liquid metal emulsions with different sizes by tailoring the flowrates of the continuous to dispersed-phase flow rates ratios φ. Large-scale preparation of liquid metal microspheres can be accomplished with this approach (as shown in Fig. 4a, b). As illustrated in Fig. 4c, with increasing flowrate ratio φ, the droplet diameter decreases from 306.6 µm at φ = 20 to 117.4 µm at φ = 120 where the disperse phase velocity is maintained at 5 µl/min. The droplet diameter’s variance tendency is resemblant with the increasing flowrate ratio for different inner phase flow velocity, namely that the average droplet diameter decreases relative dramatically when the flowratio φ is below 70 and then diminishes slowly with the increasing φ. The liquid metal droplet diameter varies with the flowrate ratio φ is in good agreement with previous research which studied the droplet formation regularity using a microcapillary device (Utada et al. 2005). Furthermore, smaller droplet with a diameter of 83 µm is obtained by increasing the inlet flow velocity to be 15 µl/min. The results show that the micro-needle induce technique offers an advanced platform for achieving uniformly distributed liquid metal droplets, which may help design and fabricate high performance miniaturized microfluidic actuators, electrical switches and so on.
4 Conclusion
In summary, we have demonstrated a convenient and reliable micro-needle induced glass capillary microfluidic device with a metallic micro-needle embedded into the inner phase capillary for large-scale preparation of Galinstan liquid metal microdroplets with good monodispersity. This distinct method is effective to overcome the Plateau–Rayleigh instability of the capillary-dominant microscale flow. When liquid metal with high interfacial tension flows along the micro-needle with suitable surface wettability, the micro-needle will introduce crucial viscous effect to restrict the hydrodynamic instability of the inner phase stream, eventually leading to the stable generation of monodispersed liquid metal droplets. By comparing the metal micro-needle and glass rod induced approach, we find that the good surface wettability between materials are also dominant in the breakup of the liquid metal. Through tuning the flow rate ratio of continuous and disperse phase, we can achieve the liquid metal microspheres of different sizes. Our strategy exhibits highly controllable flexibility and allows precise control of droplet size, which has a great potential in high-throughput fabrication of uniformly droplet emulsion with high surface tension.
References
Cheng S, Rydberg A, Hjort K, Wu Z (2009) Liquid metal stretchable unbalanced loop antenna. Appl Phys Lett 94:144103. https://doi.org/10.1063/1.3114381
Chiechi RC, Weiss EA, Dickey MD, Whitesides GM (2008) Eutectic gallium–indium (EGaIn): a moldable liquid metal for electrical characterization of self-assembled monolayers. Angew Chem Int Ed Engl 47:142–144. https://doi.org/10.1002/anie.200703642
Davis E, Ndao S (2018) On the wetting states of low melting point metal Galinstan® on silicon microstructured surfaces. Adv Eng Mater 20:1700829
de Gennes P-G, Brochard-Wyart F, Quere D (2004) Capillarity and wetting phenomena: drops, bubbles, pearls, waves. Springer, New York, pp 119–122
Dickey MD (2017) Stretchable and Soft Electronics using. Liq Met Adv Mater 29:1606425 doi. https://doi.org/10.1002/adma.201606425
Fang W-Q, He Z-Z, Liu J (2014) Electro-hydrodynamic shooting phenomenon of liquid metal stream. Appl Phys Lett 105:134104. https://doi.org/10.1063/1.4897309
Fang J, Davoudi M, Chase G (2015) Drop movement along a fiber axis due to pressure driven air flow in a thin slit. Sep Purif Technol 140:77–83
Gol B, Tovar-Lopez FJ, Kurdzinski ME, Tang SY, Petersen P, Mitchell A, Khoshmanesh K (2015) Continuous transfer of liquid metal droplets across a fluid–fluid interface within an integrated microfluidic chip. Lab Chip 15:2476–2485. https://doi.org/10.1039/c5lc00415b
Gol B, Kurdzinski ME, Tovar-Lopez FJ, Petersen P, Mitchell A, Khoshmanesh K (2016) Hydrodynamic directional control of liquid metal droplets within a microfluidic flow focusing system. Appl Phys Lett 108:164101. https://doi.org/10.1063/1.4947272
Hohman JN, Kim M, Wadsworth GA, Bednar HR, Jiang J, LeThai MA, Weiss PS (2011) Directing substrate morphology via self-assembly: ligand-mediated scission of gallium–indium microspheres to the nanoscale. Nano Lett 11:5104–5110. https://doi.org/10.1021/nl202728j
Hou L, Ren Y, Jia Y, Deng X, Liu W, Feng X, Jiang H (2017) Continuously electrotriggered core coalescence of double-emulsion drops for microreactions ACS. Appl Mater Interfaces 9:12282–12289. https://doi.org/10.1021/acsami.7b00670
Hu L, Li J, Tang J, Liu J (2017) Surface effects of liquid metal amoeba. Sci Bull 62:700–706. https://doi.org/10.1016/j.scib.2017.04.015
Jamali M, Tafreshi HV, Pourdeyhimi B (2018) Droplet mobility on hydrophobic fibrous coatings comprising. Orthogonal Fibers Langmuir 34:12488–12499
Jia Y et al (2018) Electrically controlled rapid release of actives encapsulated in double-emulsion droplets. Lab Chip 18:1121–1129. https://doi.org/10.1039/c7lc01387f
Lee D, Weitz DA (2008) Double emulsion-templated nanoparticle colloidosomes with selective. Permeab Adv Mater 20:3498–3503. https://doi.org/10.1002/adma.200800918
Liang S et al (2017) Liquid metal sponges for mechanically durable, all-soft, electrical conductors. J Mater Chem C 5:1586–1590. https://doi.org/10.1039/c6tc05358k
Lu Y et al (2015) Transformable liquid-metal nanomedicine. Nat Commun 6:10066. https://doi.org/10.1038/ncomms10066
Manzo GM, Wu Y, Chase GG, Goux A (2016) Comparison of nonwoven glass and stainless steel microfiber media in aerosol coalescence filtration. Sep Purif Technol 162:14–19
Mohammed M, Xenakis A, Dickey M (2014) Production of liquid metal. Spheres Molding Met 4:465–476. https://doi.org/10.3390/met4040465
Sen P, Chang-Jin K (2009) A fast liquid-metal droplet microswitch using EWOD-driven contact-line sliding. J Microelectromech Syst 18:174–185. https://doi.org/10.1109/jmems.2008.2008624
Shah RK et al (2008) Designer emulsions using microfluidics. Mater Today 11:18–27. https://doi.org/10.1016/S1369-7021(08)70053-1
Shay T, Velev OD, Dickey MD (2018) Soft electrodes combining hydrogel and liquid metal. Soft Matter 14:3296–3303. https://doi.org/10.1039/c8sm00337h
Shum HC, Lee D, Yoon I, Kodger T, Weitz DA (2008) Double emulsion templated monodisperse phospholipid vesicles. Langmuir 24:7651–7653. https://doi.org/10.1021/la801833a
Sivan V, Tang S-Y, O’Mullane AP, Petersen P, Eshtiaghi N, Kalantar-zadeh K, Mitchell A (2013) Liquid metal marbles. Adv Funct Mater 23:144–152. https://doi.org/10.1002/adfm.201200837
Tang S-Y et al (2014a) Liquid metal enabled pump. Proc Natl Acad Sci 111:3304–3309
Tang SY et al (2014b) Liquid metal actuator for inducing chaotic advection. Adv Funct Mater 24:5851–5858
Tang J, Zhou Y, Liu J, Wang J, Zhu W (2015) Liquid metal actuated ejector vacuum system. Appl Phys Lett 106:031901. https://doi.org/10.1063/1.4906098
Tang S-Y, Ayan B, Nama N, Bian Y, Lata JP, Guo X, Huang TJ (2016) On-chip production of size-controllable liquid metal microdroplets using acoustic waves. Small 12:3861–3869. https://doi.org/10.1002/smll.201600737
Thelen J, Dickey MD, Ward T (2012) A study of the production and reversible stability of EGaIn liquid metal microspheres using flow focusing Lab. on a Chip 12:3961–3967. https://doi.org/10.1039/C2LC40492C
Utada A, Lorenceau E, Link D, Kaplan P, Stone H, Weitz D (2005) Monodisperse double emulsions generated from a microcapillary device. Science 308:537–541
Wei Z et al (2014) Liquid metal/metal oxide frameworks. Adv Funct Mater 24:3799–3807. https://doi.org/10.1002/adfm.201304064
Wissman J, Dickey MD, Majidi C (2017) Field-controlled electrical switch with liquid metal. Adv Sci (Weinh) 4:1700169. https://doi.org/10.1002/advs.201700169
Yoo K, Park U, Kim J (2011) Development and characterization of a novel configurable MEMS inertial switch using a microscale liquid-metal droplet in a microstructured channel. Sens Actuators A Phys 166:234–240. https://doi.org/10.1016/j.sna.2009.12.008
Yu Y, Wang Q, Yi L, Liu J (2014) Channelless fabrication for large-scale preparation of room temperature liquid metal. Droplets Adv Eng Mater 16:255–262 doi. https://doi.org/10.1002/adem.201300420
Acknowledgements
This work was supported by the National Natural Science Foundation of China (Grant nos. 11672095, 11802078, 11702035 and 11572335), the Foundation for Innovative Research Groups of the National Natural Science Foundation of China (Grant no. 51521003), the CAS Key Research Program of Frontier Sciences (QYZDB-SSW-JSC036), the CAS Strategic Priority Research Program (XDB22040403), and University Nursing Program for Young Scholars with Creative Talents in Heilongjiang Province (Grant no. UNPYSCT-2018104).
Author information
Authors and Affiliations
Corresponding authors
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
This article is part of the topical collection “2018 International Conference of Microfluidics, Nanofluidics and Lab-on-a-Chip, Beijing, China” guest edited by Guoqing Hu, Ting Si and Zhaomiao Liu.
Electronic supplementary material
Below is the link to the electronic supplementary material.
Supplementary material 1 (WMV 5385 KB)
Supplementary material 2 (WMV 1816 KB)
Rights and permissions
About this article
Cite this article
Hu, Q., Ren, Y., Zheng, X. et al. A micro-needle induced strategy for preparation of monodisperse liquid metal droplets in glass capillary microfluidics. Microfluid Nanofluid 23, 13 (2019). https://doi.org/10.1007/s10404-018-2180-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s10404-018-2180-z