Abstract
Phosphate sorption and desorption experiments were conducted with four ferruginous soils (alfisols) of Eastern India, in view of the low native phosphate concentrations in tropical Indian soils. From the P-isotherm curve, standard P requirement (SPR) of the soils was determined. Phosphate sorption data were fitted to both Langmuir and Freundlich equations and mean sorption maximum values obtained for the different soil series were in the decreasing order as Matimahal > Anandapur > Mrigindih > Kashipur. The fraction of added P sorbed followed the same trend as SPR, P sorption maximum (Pmax), phosphate affinity constant (K), maximum phosphate buffering capacity (MPBC), Freundlich constant K′ and phosphate desorption values. Phosphate sorption maximum was significantly correlated with MPBC, Freundlich 1/n, SPR, clay and different forms of Fe and Al. The value of K (bonding energy) was significantly correlated with MPBC, Freundlich K′ and pyrophosphate extractable Fe and Al. The MPBC was significantly correlated with Freundlich K′, Freundlich constant 1/n, clay, oxalate and dithionite extractable, amorphous and crystalline form of Fe and Al. Freundlich K′ was significantly correlated with Freundlich 1/n, pHwater, clay, dithionite extractable and crystalline form of Fe and Al. The results suggested that the soils having higher amount of extractable and reactive Fe and Al shared higher P sorbtion capacity and such soils may need higher levels of P application
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
Ferruginous soils (alfisols) are the dominant soils of the semi-arid tropics where crop yield is often limited due to low native soil P concentration (Dolui and Dasgupta 1998). The problem of low soil P increases with the lowering of soil pH, since in acid soil the applied soluble phosphate fertilizer gets fixed through adsorption and precipitation, although the former appears to be dominant over a short reaction period (Mehadi and Taylor 1988; Sanyal and De Dutta 1991). Sorption and desorption reactions have a large impact on P availability to plants. Applied P is sorbed on the surface of inorganic constituents mainly by ligand exchange mechanism that provided its concentration in the soil solution which is not very high. Appreciable desorption of this P is possible if the negative charge on the surface is increased by raising the solution pH, or by introducing a competitive anion which could be specifically adsorbed by increasing the negative charge of the soil in the presence of P (Dolui et al. 1991). The P sorption by soil is important because sorbed P equilibrates with soil solution P, which in turn is the immediate source of P for plants. Phosphate sorption isotherms integrate P intensity, capacity and quantity parameters of soil. These factors play key roles in controlling P flux to the root of growing plants. The ability of the soil to replenish soil solution P, i.e., the desorption capacity; intensity and rate are important factors influencing uptake of P by plants and their growth. These factors are all interdependent and P availability can be expressed by a combination of two or more factors.
Soil factors influencing P sorption desorption include amount and type of clay, amounts of iron and aluminum oxides, organic matter content, pH and calcium carbonate content (Mehadi and Taylor 1988; Solis and Torrent 1989; Tsadilas et al. 1996; Chand et al. 1995; Saha et al. 1999) Phosphate sorption by the soils can be described by many equations, with Langmuir and Freundlich equations being the most commonly used. Using these equations, a number of P-sorption indices can be determined that describe the P-sorption capacity of soils. Phosphorus sorption–desorption phenomenon has been widely studied on Indian soils. Alfisols from different parent materials differ in their properties, which in turn significantly influence P sorption–desorption in the soils. The present investigation was carried out with the following objectives: (i) to determine the ability of representative Alfisols to adsorb P under laboratory conditions and to compare sorption isotherms among soil series; (ii) to determine the effects of the P sorption capacity and P affinity constant (K′) on the quantity of added P, recovered with Bray’s 1 extractant and (iii) to develop regression equations and use existing soil characteristics to predict relative P sorption potentials in some Alfisols.
Materials and methods
Four soil profiles of Alfisols under hot, dry, sub humid agro ecological sub region (12.3) from Puruliya district of West Bengal, India, were selected. Major site characteristics and land use pattern were given in Table 1. The samples were air dried and passed through 2-mm sieve.
Soil pH was determined in 1:2.5 soil:water suspensions. Electrical conductivity was determined in 1:5 soil:water suspension. Particle size distribution was determined by conventional international pipette analysis following destruction of organic matter with hydrogen peroxide; and organic carbon by the standard Walkey and Black method as cited by Piper (1966). Cation exchange capacity (CEC) was determined by 1 M ammonium acetate (pH 7.0).
Available P was extracted using Bray’s 1 extractant (soil and extractant ratio 1:10) and determined following the methodology of Jackson (1973). Free Fe and Al fractions (Table 2) were determined by separate (not sequential) extraction with (1) 0.1 M sodium pyrophosphate (Agriculture Canada 1984), (2) 0.2 M ammonium oxalate adjusted to pH 3.0 (Agriculture Canada 1984) and (3) dithionate-citrate-bicarbonate reagent (CSSC Subcommittee on methods of analysis 1978), according to standard soil survey methods (USDA 1972). It is generally believed that extraction (1) removes organically bound Fe and Al (Fep, Alp), (2) removes organically bound plus inorganic amorphous (Feo, Alo) and (3) removes organically bound, inorganic amorphous and crystalline (Fed, Ald) (Parafitt and Childs 1988; Borggaard 1988). Amorphous Fe and Al were designated as Feo–Fep and Alo–Alp, crystalline Fe and Al as Fed–Feo and Ald–Alo and active Fe and Al ratios as Feo:Fed and Alo:Ald, respectively.
Sorption experiment
The sorption isotherm was determined by equilibrating (at 25±1°C) 3 g soil samples with 30 ml of 0.01 M CaCl2 containing 0, 10, 20, 30, 40, 50 and 80 mg P L−1. Two drops of toluene were added to arrest microbial growth. The suspensions were shaken horizontally for 30 min (180+ oscillations/min) each day, for 60 days. After equilibration, the suspension was centrifuged at 8,000 rpm for 20 min and the P content in the clear supernatant solution was determined by depletion technique (Olsen and Watanabe 1957). The amount of P sorbed was calculated by subtracting the amount of P in the extract from amount of P initially added (Fox and Kamprath 1970). Phosphorus sorbed (mg kg−1) versus P remaining in solution (mg L−1) was plotted to determine the sorption isotherm. The sorption values of each soil were plotted according to the Langmuir isotherm:
where C is equilibrium P concentration (mg L−1), x/m is the amount of sorbed P (mg kg−1), m, b are the constants related to P sorption maximum (mg kg−1) and K is the bonding energy (L mg−1), respectively. The plot of C/(x/m) versus C should give a straight line from which b −1 (slope) and K (slope or intercept) can be calculated.
Maximum P buffering capacity (MPBC) is the product of P sorption capacity (or monolayer coverage in mol P Kg−1 of soil) and phosphate affinity constant related to the binding strength (Dalal and Hallsworth 1976) and regulates the partition of P between solution and solid phase.
The Freundlich equation takes the form:
where x/m is the phosphorus sorption in mg kg−1 of soil, C is the equilibrium concentration in mg L−1, K′ and n are two constants where n is always greater than unity. By taking the logarithm, Eq. (2) changes into log x/m = log K′+1/n log c. The log equation gives a straight line, or linear curve where log K′ is the intercept and 1/n represents the slope of the curve or the regression coefficient.
Desorption experiment
The soil from the sorption run (after the supernatant solution was decanted off) was washed with alcohol to free the soil of soluble P. The washed soil was stirred continuously with 30 ml of Bray’s 1 extractant for 5 min (180+ oscillations/min) and then centrifuged at 8,000 rpm for 20 min. The percentage of P desorbed was then calculated.
Result and discussion
Phosphate sorption characteristics
P sorbed at various equilibrating P concentrations and that remaining in solution at equilibrium is shown in Table 3. The P sorption in soil increased with increasing levels of P added to the soil. At low concentration the relationship was essentially linear while higher concentration showed some evidence of deviation from linearity. The linear relationship at lower P concentrations was probably due to the large intermolecular distance between P molecules, which resulted in negligible mutual repulsion. Deviation from the straight line indicated that the bonding energy is a decreasing function of increasing surface—saturation (Barrow 1978).
The results revealed that at all concentrations mean sorbed P was highest in the Matimahal soil series followed by Anandapur, Mrigindih and Kasipur series. The higher P sorption capacity of the Matimahal series could be attributed to the specific clay surface and amorphous and crystalline form of iron and aluminum oxide present in these soils. Lower sorption observed in the Kasipur soil series as compared to the other series might be due to comparatively low clay content and amorphous and crystalline from of iron and aluminum oxides (Kaistha et al. 1997) along with relatively higher pH (Hinga 1973) of these soils. Moderately weathered crystalline oxides, desilicated amorphous materials and various forms of sesquioxides adsorb high amount of P (Fox 1981).
Phosphate sorption parameters
The P sorption data of the soils from the four soil series were plotted according to the conventional Langmuir equation. The Langmuir isotherm was used only as a means of deriving a characteristic sorption maximum indicative of the soil capacity to sorb P. The amount of P sorbed at 0.2 mg P L−1 equilibrium concentration is considered to be adequate for most field crops and is widely accepted as the standard P requirement (SPR) of soils (Fox 1981). In the four soil series considered here the SPR of the soils varied from 11 to 25 mg kg−1 with an average of 18.9 mg kg−1 (Table 4). The highest SPR was observed in Matimahal (23.8 mg kg−1) soils followed by the Anandapur (21.0 mg kg−1), Mrigindih (18.8 mg kg−1) and Kasipur (12.0 mg kg−1) series. However, no specific trend of SPR was observed with depth.
Phosphate sorption maximum and bonding energy
Phosphate sorption maximum of the soil based on the first linear portion of the isotherms varied widely and ranged from 385 mg to 833 mg kg−1 (Table 4). Phosphate sorption maxima were highest in Anandapur series followed by Matimahal, Mrigindih and Kasipur series. The SPR, Frendulich K′ and 1/n values were highest in Matimahal series, but bonding energy and MPBC were highest in Anandapur series.
The bonding energy K calculated from the Langmuir equation followed the similar trend as P sorption maximum (Pmax). Small K values indicated loose bonding (Mehadi and Taylor 1988), which might suggest that the Anadapur and Matimahal series could probably retain P better than Mringindih and Kasipur series and could possibly be the better P sink at similar P adding rates. Higher P retention characteristics of the Matimahal and Anadapur series could be attributed to the higher clay and organic carbon, higher Fe and Al concentration (Mallikarjuna et al. 2003) compared with Mrigindih and Kasipur series (Tables 2, 5). The parameter K of the Langmuir equation varied from 14 to 0.63 L mg−1 with a mean of 0.20 L mg−1. These values were lower as compared to those reported by Solis and Torrent (1989) for calcareous Vertisol and Inceptisols from Spain but in the same order as those reported by Choudhuary et al. (1993) for semi-arid soils of Punjab. Higher value of phosphate sorption and bonding energy could be attributed to low CEC, which indicated the dominance of kaolinite, which played an active role in P sorbtion (Tomar 2000).
Maximum P buffering capacity
Maximum P buffering capacity (MPBC) is an inherent characteristic of soils, which unlike P buffering capacity does not vary with solution P concentration and its use was advocated by Holford and Mattingly (1976). The MPBC ranged from 67.6 to 286 L kg−1 with a mean of 116.8 L kg−1. Anandapur series showed the highest MPBC (average 178.58 L kg−1) followed by the other soil series. MPBC generally increased with depth in the different soil series with some irregular trends in few horizons. These variations in the buffering capacity of soils of the same soil series were due to variation in clay percent and Fe and Al oxides (Dhillon et al. 2004), which were generally increased down the profile. Buffering capacity values were assessed from changes in P quantity and intensity produced by cropping, i.e., the ratio between change in labile P and change in the solution P concentration (Δ labile P/Δ P concentration) (Dolui et al.1998). Thus, sorption isotherms can provide a rough estimate of the field P buffering capacity in the soils studied, as also found in other soils (Bowman and Olsen 1985). Management practices viz soil conservation measure, application of manure, lime, etc. also influences MPBC (Majumdar et al. 2004) and difference in MPBC in four soil series can be explained by different land use pattern of these soil series. Mrigindih soil series, which is a pasture land, received lowest level of management practices showed lowest MPBC value.
Freundlich sorption isotherm
Freundlich equation gave a better fit of the equilibrium P sorption data than did the Langmuir equations. This is because the Freundlich equations although originally empirical, implies that affinity for sorption decreases exponentially with increasing saturation of the surface, which is closer to reality than the assumption of a constant bonding energy inherent in the Langmuir equations (Sposito 1981; Kuo and McNeal 1984; Sanyal and De Dutta 1991). Such behavior is supported by the findings of Polyzopoulos et al. (1985) and Saha et al. (1999). The Freundlich constant varied from 115 to 219 mg kg−1 with an average of 142 mg kg−1. The coefficient 1/n (Table 4) values were in the same order as that observed by Tsadilas et al. (1996). However, no systematic depth wise trend was observed.
Desorption of sorbed P
Desorption percent of sorbed P from the surface and sub-surface soil by Bray’s 1 extractant is shown in Figs. 1 and 2. The amount of sorbed P extracted varied considerably among the soil series, which suggested that some additional soil factors also affected the amount desorbed by the extractant. The mean desorption of sorbed P was highest in the Anandapur soil series, followed by the Mrigindih, Matimahal series and Kasipur series.
The maximum recovery was determined for each soil as ratio of the total amount of P extracted to the total amount of P sorbed. The range of P desorbed and mean maximum recovery followed the order: Mrigindih (12.8–17.7%, mean 14.9%) > Kasipur (13.2 m–16.6%, mean 14.9%) > Anandapur (10.0–11.4%, mean 10.9%) > Matimahal (8.9–11.7%, mean 10.2%), which followed the decreasing trend of P desorption. The amount of P desorbed increased with the amount of P originally sorbed, but the relationship was not described by any simple function. In accordance with the results obtained by other workers (Shailaja and Sahrawat 1990), the present results also indicated that applied P was not all irreversibly fixed; however, further study is required for determination of the factors affecting P desorption using different extractants.
Relationships among the P sorption parameters and soil properties
The relationship among the P sorption parameters and soil properties are presented in Table 6. Phosphate sorption maximum was significantly related to MPBC, Freundlich 1/n, SPR, clay and different form of Fe and Al. Since the sorption maximum (b) is a component of the buffering capacity, a relationship between P sorption maximum and bonding energy with MPBC may be expected. The SPR was correlated with sorption maximum showing that both parameters could be used in evaluating the P sorption characteristic of the soils (Osodeke et al. 1993). Murthy et al. (1996) reported that sorption maximum was significantly associated with Freundlich K′. The result supported the suggestion by Hinga (1973) and Dolui and Dasgupta (1998) who concluded that different forms of Fe and Al components are very active in the sorption of P added to soils.
The value of K (bonding energy) correlated significantly with MPBC was expected, as affinity constant (K) is a component of the buffering capacity. The significant association of Freundlich K′ with sorption maximum and bonding energy constant showed their interdependence. The surface site assumed to have constant affinity and the electrostatic interaction was separated from the chemical components. The breakdown of sorption energy into chemical and electrostatic components was arbitrary (Sparks 1984) due to the lack of knowledge about the activity coefficient surface species (Sposito 1984).
Maximum P buffering capacity was significantly correlated with sorption parameters and soil properties, viz., Freundlich K′, 1/n, clay and different forms of Fe and Al. The value of Freundlich K′ was significantly correlated clay content attributed to the high surface area of clay particles, which provides for P sorption (Tsadilas et al. 1996). It indicates that, in the present contest abundance of amorphous and crystalline oxide of Fe and Al in alfisols reduces the leaching loss of phosphorus from the soil (Agbenin 2003), whereas comparatively low clay content in Mrigindih soil series increase the risk of phosphorus loss through leaching. The correlation coefficient of Freundlich K′ with oxalate and dithionite soluble Fe and Al and crystalline Fe and Al were similar in magnitude as the values obtained for the different group of soils in the Mediterranean areas (Borrero et al. 1988), which indicated the important role of Fe and Al oxides in P sorption.
Conclusions
Phosphate fertilizers have immense contributions toward crop yield and play significant role in maintaining the soil physical properties. Low to medium available phosphorus in the soils was mainly due to acidic pH and presence of Fe and Al oxides. Using the standard value of 0.2 mg P L−1 in the equilibrium solution as that adequate for normal growth of most crops, the amount of P-fertilizers required to give this value for the studied soils ranged from 11 mg to 25 mg P L−1. In the studied soils, moderate slope associated with high rainfall and low organic carbon status increased the risk of phosphate runoff. But acidic soil condition associated with dominance of kaolinite clay materials, low to medium status of available phosphorus and higher amount of Fe and Al oxide increased the phosphate adsorption capacity of the soil. This restricted the movement of phosphate and regulated the leaching loss. Therefore, broadcasting of phosphate fertilizer should be avoided in the area and slow releasing phosphate fertilizer should be applied in smaller, more frequent dozes for higher crop response.
References
Agbenin JO (2003) Extractable iron and aluminum effects on phosphate sorption in a Savanna Alfisol soil. Sci Soc Am J 67:589–595
Agriculture Canada (1984) Analytical methods manual. In: Sheldrick BH (ed) Land Resource Research Institute, Ottawa, LLRI Contribution. pp 84–90
Barrow NJ (1978) The desorption of phosphate adsorption curves. J Soil Sci 29:447–462
Borggaard OK (1988) Phase identification by selective dissolution techniques. In: Stucki JW, Goodman BA, Schwertmann U (eds) Iron in soils and clay minerals. D. Reidel Publishing Company Boston, USA
Borrero CF, Pena F, Torrent J (1988) Phosphate sorption by calcium carbonate in some soils of the Mediterranean part of Spain. Geoderma 42:261–269
Bowman RA, Olsen SR (1985) Assessment of phosphate buffering capacity: 2, Green house method. Soil Sci 140: 387–392
Canada Soil Survey Committee. Subcommittee on Methods of Analysis (1978) In: McKeague JA (ed) Manual of soil sampling and methods of analysis. Canadian Society of Soil Science, Ottawa, pp 98 – 106
Chand M, Randhawa NS, Vig AC (1995) Standardization of equilibration time for phosphorus adsorption studies in low P fixing alluvial Soils. J Ind Soc Soil Sci 43:676–678
Choudhary OP, Arora BR, Hundal HS (1993) Phosphate sorption characteristics of arid and semi-arid soils of Punjab, India, as influenced by ionic composition of the supporting medium. Arid Soil Res Rehab 7:293–301
Dalal RC, Hallsworth EG (1976) Evaluation of the parameters of soil phosphorus availability factors in predicting yield response and phosphorus uptake. Soil Sci Soc Am J 40:541–546
Dhillon NS, Dhesi TS, Brar BS (2004) Phosphate sorption-desorption characteristics of some ustifluvents of Punjab. J Ind Soc Soil Sci 52:17–22
Dolui AK, Dasgupta M (1998) Phosphate sorption- desporption characteristics of ferruginous soils (Alfisols) of eastern India. Agropedology 8:76–83
Dolui AK, Mukhopadhyay M, Nayek AK (1991) Effect of phosphatic fertilizer on charge characteristics of soils in the tropics. Int J Trop Agric 9:259–266
Fox RL (1981) External phosphorus requirements of crops. In: Dowdy RH (ed) Chemistry in the soil environment. ASA Special Publication, No. 40. Am Soc Agron, Madison, WI, USA
Fox RL, Kamprath EJ (1970) Phosphate sorption isotherms for evaluating the phosphate requirement of soils. Soil Sci Soc Am Proc 34:902–907
Hinga G (1973) Phosphate sorption capacity in relation to properties on several types of Kenya soil. East Afr Agric For J 38:400–404
Holford ICR, Mattingly GEG (1976) A model for the behaviour of labile phosphate in soil. Plant Soil 44:219–229
Jackson ML (1973) Soil chemical analysis. Prentice Hall, New Delhi
Kaistha BP, Sharma PK, Sharma RP (1997) Influence of Soil components on phosphorus fixing capacity of some Alfisolsin Himachal Pradesh. J Ind Soc Soil Sci 45:261–264
Kuo S, McNeal BL (1984) Effect of pH and phosphate on cadmium sorption by a hydrous ferric oxide. Soil Sci Soc Am J 48:1040–1044
Majumdar B, Venkatesh MS, Kumar K, Patiram (2004) Effect of different farming systems on phosphorus fractions in an acid alfisols of Meghalaya. J Ind Soc Soil Sci 52:29–34
Mallikarjuna G, Sudhir K, Srikanth K, Srinivasamurty CA (2003) Phosphorus fixation capacity and its relationship with soil characteristics in laterite soils of Karnataka. J Ind Soc Soil Sci 51:23–25
Mehadi AA, Taylor RW (1988) Phosphate adsorption by two highly weathered soils. Soil Sci Soc Am J 52:627–632
Murthy IYLN, Sastry TG, Datta SC, Naryanasamay G, Rattan RK (1996) Phosphorus adorption In relation to soil characteristics of vertisols derived from different parent materials. J Ind Soc Soil Sci 44:224–229
Olsen SR, Watanabe FS (1957) A method to determine phosphorus adsorption maxima of soils as measured by the Langmuir isotherm. Soil Sci Soc Am Proc 21:144 – 149
Osodeke, VE, Asawalam DOK, Kamalu OJ, Ugwa IK (1993) Phosphorous sorption characteristics of some soils of the rubber belt of Nigeria. Commun Soil Sci Plant Anal 24:1733–1743
Parafitt RL, Childs CW (1988) Estimation of forms of Fe and Al: a review and analysis of contrasting soils by dissolution of Moessbauer methods. Aust J Soil Res 26:121–144
Polyzopoulos NA, Keramidas VZ, Kiosse H (1985) Phosphate sorption by some Alfisols of Greece as describe by commonly used isotherm. Soil Sci Soc Am J 49:81–84
Saha SA, Dutta A, Sanyal SK (1999) Phosphate sorption desorption characteristic of some acidic soils. J Ind Soc Soil Sci 47:34–49
Sanyal SK, De Dutta SK (1991) Chemistry of phosphorus transformation in Soil. Adv Soil Sci 16:1–120
Shailaja S, Sahrawat KY (1990) Adsorption and desorption of phosphate in semiarid tropical Indian vertisols. Fertil Res 23:87–96
Solis P, Torrent J (1989) Phosphate sorption by calcareous vertisols and inceptisols of Spain. Soil Sci Am J 53:456–459
Sparks DL (1984) Ion activities: a historical and theoretical overview. Soil Sci Am J 48:514–518
Sposito G (1981) The operational definition of the zero-point of charge in soils. Soil Sci Soc Am J 51:292–297
Sposito G (1984) The surface chemistry of soils. Oxford University Press, USA
Tomar NK (2000) Dynamics of phosphorus in soils. J Ind Soc Soil Sci 48:640–673
Tsadilas CD, Samaras V, Dimoyiannis D (1996) Phosphate sorption by red Mediterranean soils from Greece. Commun Soil Sci Plant Anal 27:2279–2293
USDA (1972) Soil survey laboratory methods and procedures for collecting soil samples, Soil Survey Investigation Report, No. 1. USDA, US Government Printing Office, Washington
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Bera, R., Seal, A., Bhattacharyya, P. et al. Phosphate sorption desorption characteristics of some ferruginous soils of tropical region in Eastern India. Environ Geol 51, 399–407 (2006). https://doi.org/10.1007/s00254-006-0335-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00254-006-0335-9