Abstract
n view of the influence of cutting heat and cutting force on the machining precision of micro-machining, this paper carries out micro-milling temperature measurements and deformation measurement tests based on the theoretical model of temperature field distribution of workpiece and the simulation model of workpiece deformation, providing technical basis for the high-precision machining of precision micro-parts. A theoretical model for the description of the increase in the cutting temperature of the workpiece is established prior to using an inverse evaluation method for solving the heat source intensity iteratively. During the finite element analysis of the distribution of the temperature field and heat distortion, the process of the heat transfer is simplified as a process of applying a series surface heat source to workpiece. Besides, this paper carried on a series of micro-milling experiments, used a fast-response thermocouple which has a property of self-renewal for the measurement of the change of the workpiece temperature, the response time of the applied thermocouple is within the magnitude of microsecond, and then, a high-frequency amplifier and an electric potential acquisition equipment were used to gain the transient temperature in the cutting area; meanwhile, a dynamometer is applied to measure the three-directional forces, and finally, the workpiece deformation would be measured by the Keyence microscope. Through the comparison of the simulated temperature and deformation with the experimental results, the simulation model showed considerable reliability.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Masuzawa T, Tönshoff HK (1997) Three-dimensional micromachining by machine tools. CIRP Ann Manuf Technol 46(2):621–628
Liu X, DeVor RE, Kapoor SG, Ehmann KF (2004) The mechanics of machining at the microscale: assessment of the current state of the science. J Manuf Sci Eng 126(4):5064–5070
Chae J, Park SS, Freiheit T (2006) Investigation of micro-cutting operations. Int J Mach Tools Manuf 46(3–4):313–332
Liu K, Melkote SN (2007) Finite element analysis of the influence of tool edge radius on size effect in orthogonal micro-cutting process. Int J Mech Sci 49(5):650–660
Bao WY, Tansel IN (2000) Modeling micro-end-milling operations. Part I: analytical cutting force model. Int J Mach Tools Manuf 40(15):2155–2173
Bao WY, Tansel IN (2000) Modeling micro-end-milling operations. Part II: tool run-out. Int J Mach Tools Manuf 40(15):2175–2192
Bao WY, Tansel IN (2000) Modeling micro-end-milling operations. Part III: influence of tool wear. Int J Mach Tools Manuf 40(15):2193–2211
Vogler MP, KaPoor SG, Devor RE (2004) On the modeling and analysis of machining performance in micro-end-milling, part11: cutting force prediction. J Manuf Sci Eng 126(4):695–705
Zhou Z (1985) Metal cutting principle. Shanghai Scientific and Technical Publishers Shanghai, pp 28–62
Push AV (1987) Predication of thermal displacements in spindle units. Sov Eng Res 5(5):42–47
Lin S, Peng F, Wen J (2013) An investigation of workpiece temperature variation in end milling considering flank rubbing effect. Int J Mach Tools Manuf 73(7):71–86
Grzesik W, Bartoszuk M, Nieslony P (2005) Finite element modelling of temperature distribution in the cutting zone in turning processes with differently coated tools. J Mater Process Technol s164–165(10):1204–1211
Jiang F, Liu Z, Wan Y (2013) Analytical modeling and experimental investigation of tool and workpiece temperatures for interrupted cutting 1045 steel by inverse heat conduction method. J Mater Process Technol 213(6):887–894
Carvalho SRD, Machado AR, Silva MBD (2014) Analyses of effects of cutting parameters on cutting edge temperature using inverse heat conduction technique. Math Probl Eng (6):1–11
Rai JK, Xirouchakis P (2009) FEM-based prediction of workpiece transient temperature distribution and deformations during milling. Int J Adv Manuf Technol 42(5–6):429
Lazoglu I, Altintas Y (2002) Prediction of tool and chip temperature in continuous and interrupted machining. Int J Mach Tools Manuf 42(9):1011–1022
Yang Y, Zhu W (2014) Study on cutting temperature during milling of titanium alloy based on FEM and experiment. Int J Adv Manuf Technol 73:1511–1521
Hsu CY, Huang CK, Wu CY (2007) Milling of MAR-M247 nickel-based superalloy with high temperature and ultrasonic aiding. Int J Adv Manuf Technol 34(9–10):857–866
Zhang F (2012) Investigations on transient cutting temperature of tool and workpiece in high-speed milling. Shandong University
Luo Z (2009) Thrmo mechanical coupling simulation and experimental study of micro milling process. Harbin Institute of Technology, pp 12–34
Tang D, Sun H, Jiao L (2008) A study on prediction approach of the workpiece’s face milling deformation. Trans Beijing Inst Technol 28(8):678–681
Liu G, Tan G, Li G (2009) Experiment, modeling, and analysis for temperature field of milling insert. Int J Adv Manuf Technol 40(1–2):67–73
Richardson DJ, Keavey MA, Dailami F (2006) Modelling of cutting induced workpiece temperatures for dry milling. Int J Mach Tools Manuf 46(10):1139–1145
Kaminise AK, Guimarães G, Silva MBD (2014) Development of a tool–work thermocouple calibration system with physical compensation to study the influence of tool-holder material on cutting temperature in machining. Int J Adv Manuf Technol 73(5–8):735–747
Chen G, Ren C, Zhang P (2013) Measurement and finite element simulation of micro-cutting temperature of tool tip and workpiece. Int J Mach Tools Manuf 75(12):16–26
Rahman M, Kumar AS, Salam M- u (2003) Effect of chilled air on machining performance in end milling. Int J Adv Manuf Technol 21(10–11):787–795
Thepsonthi T, Hamdi M, Mitsui K (2009) Investigation into minimal-cutting-fluid application in high-speed milling of hardened steel using carbide mills. Int J Mach Tool Manuf 49(2):156–162
Cao Y, Zhang H, Dong H, Li M (2006) Comparison Study on Dry and Wet Cutting Quenched Steel with PCBN. Tool Eng 40(5):19–21
Jia G, Wang X (2016) Experimental study on dry and wet cutting of coated carbide tools. Sci Res (12):138–139
Hou Z, He S, Li S (1984) Solid heat conduction. Shanghai science and Technology Press, Shanghai
Beck JV, Blackwell B, Clair CR (1985) Inverse heat conduction: ill-posed problems. A Wiley-Interscience Publication, Hoboken
Acknowledgements
This work has been supported by the Natural Science Foundation of China (No.51575050 and No.51505034).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Peng, Z., Li, J., Yan, P. et al. Experimental and simulation research on micro-milling temperature and cutting deformation of heat-resistance stainless steel. Int J Adv Manuf Technol 95, 2495–2508 (2018). https://doi.org/10.1007/s00170-017-1091-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-1091-6