Abstract
This paper presents a theoretical and experimental study of the dynamic temperature field on a milling insert with complex groove. Experimental measurements of milling temperature using the thermocouple technique were performed. A mathematical model of the temperature field of the insert was established. A finite element model of the insert was built to simulate the temperature field. The boundary condition was determined by the experimental data and mathematical calculation, and then the temperature field of the milling insert was simulated through finite element analysis. The temperature distribution in a cut-in/cut-out cycle was obtained.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Tan G, Yuan J, Wang X, Yuan ZJ (1997) Cause for exit failure of end mill. J Harbin Inst Technol 4(7):107–111
Deshayes L (2007) Analysis of an equivalent tool face for the cutting speed range prediction of complex grooved tools. J Mater Process Technol 190(1–3):251–262
Ee KC, Balaji AK, Jawahir IS (2003) Progressive tool-wear mechanisms and their effects on chip-curl/chip-form in machining with grooved tools: an extended application of the equivalent toolface (ET) model. Wear 255(7–12):1404–1413
Jawahir IS, Li PX, Ghosh R, Exner EL (1995) A new parametric approach for the assessment of comprehensive tool-wear in coated grooved tools. CIRP Ann 45(1):49–54
Jawahir IS, van Luttervelt CA (1993) Recent developments in chip control research and applications. CIRP Ann 42(2):659–693
Jawahir IS, Ghosh R, Balaji AK, Li PX (2000) Predictability of tool failure modes in turning with complex grooved tools using the equivalent toolface (ET) model. Wear 244(1):94–103
Jawahir IS, Wang X (2007) Development of hybrid predictive models and optimization techniques for machining operations. J Mater Process Technol 185(1–3):46–59
Ghosh R, Redetzky M, Balaji AK, Jawahir IS (1996) The equivalent toolface (ET) approach for modeling chip curl in machining with grooved tools. Proceedings of the 13th symposium on engineering applications in mechanics, McMaster University, ON, Canada, pp 702–711
Zhang H, Dillon OW, Jawahir IS (2001) A finite element analysis of 2D machining with a grooved tool. Transactions of the North American Manufacturing Research Institution of SME (XXIX):327–334
Li G, Liu G, Tan G, Li Z, Rong Y (2005) Reconstruction technique of 3D complex groove of milling insert based on genetic algorithms. Chinese J Mech Eng 41(6):113–117
Li Z, Zhang Z, Yan F, Dong L, Tao H, Wei Y, Rong Y (2000) Waved-edge insert development and milling force model. Chinese J Mech Eng 36(10):42–45
Tan G, Liu G, Li Z, Liu M, Li G, Rong Y (2004) 3D temperature field analysis and fuzzy comprehensive evaluation for milling insert with complex groove. Chinese J Mech Eng 40(3):106–110
El Hossainy TM, El-Shazly MH, Abd-Rabou M (2001) Finite element simulation of metal cutting considering chip behavior and temperature distribution. Mater Manuf Process 16(6):803–814
Elmoussami H, Battaglia JL (2003) A method to estimate the average temperature on the cutting edge of tools: application on the milling process. Exp Heat Transf 16(2):139–158
Hou ZB, He SJ, Li SX (1984) Heat conduction in solids. Shanghai Science and Technology Press, China
Poppe GPM, Wijers CMJ (1990) More efficient computation of the complex error function. ACM Trans Math Softw 16(1):38–46
Berliner EM, Knainov VP (1991) Analytic calculation of the temperature field and heat flows on the tool surface in metal cutting due to sliding friction. Wear 143(2):379–395
Masuda M, Sato T, Kori T, Chujo Y (1994) Cutting performance and mechanism of alumina-based ceramic tools when machining austempered ductile iron. Wear 174(1–2):147–153
Radules R, Kapoor SG (1994) An analytical model for prediction of tool temperature fields during continuous and interrupted cutting. J Eng Ind 116(22):135–143
Liu D, Yu X, Lou P (1999) Finite element analysis of the temperature distribution in orthogonal metal machining. J Beijing Inst Technol 8(4):386–391
Fel’adshtein EE, Kaminski VL (2001) Modeling of the thermal field of a workpiece in milling of austenitic steel by a finger-type cutter. J Eng Phys Thermophys 74(1):149–152
El Hossainy TM, El-Shazly MH (2001) Finite element simulation of metal cutting considering chip behavior and temperature distribution. Mater Manuf Process 16(6):803–814
Du F, Lovell MR (2001) Boundary element method analysis of temperature fields in coated cutting tools. Int J Solids Struct 38(26–27):4557–4570
Abukhshim NA, Mativenga PT, Sheikh MA (2006) Heat generation and temperature prediction in metal cutting: a review and implications for high speed machining. Int J Mach Tools Manuf 46(7–8):782–800
Hsu CY, Huang CK, Wu CY (2007) Milling of MAR-M247 nickel-based superalloy with high temperature and ultrasonic aiding. Int J Adv Manuf Technol 34(9–10):857–866
Astakhov VP (2007) Effects of the cutting feed, depth of cut, and workpiece (bore) diameter on the tool wear rate. Int J Adv Manuf Technol 34(7–8):631–640
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Liu, G., Tan, G. & Li, G. Experiment, modeling, and analysis for temperature field of milling insert. Int J Adv Manuf Technol 40, 67–73 (2009). https://doi.org/10.1007/s00170-007-1322-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-007-1322-3