Abstract
In the process of micro end-milling, the micro tool axis is not the same line of the spindle axis due to the eccentricity of the tool-holder-spindle assembly, which is called tool runout. Tool runout has significant effects on cutting force variation, which can lead to higher peak forces and uneven tool wear of the cutter. Hence, a runout model must be included in a cutting force modeling to simulate accurate cutting force during micro-milling process. In this paper, the method for modeling and simulation to measure a runout of tool-holder-spindle in micro end-mill was developed. The simulated cutting force with regard to runout was compared with the measured cutting force. It is noted that they had similar variation pattern and closely matched amplitude levels. The result indicated that the effects of tool runout were predominant for the 0.9 mm diameter and at low feed per tooth.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Kang IS, Kim JS, Kim JH, Kang MC, Seo YW (2007) A mechanistic model of cutting force in the micro end milling process. J Mater Process Technol 187-188(12):250–255
Ko JH, Cho DW, Ko TJ (2003) Off-line feed rate scheduling for 3D ball-end milling using a mechanistic cutting force model, trans. NAMRI/SME 31:113–120
Vogler MP, DeVor RE, Kapoor SG (2003) Microstructure-level force prediction model for micro-milling of multi-phase materials. Journal Manufacturing and Science Engineering 125(2):202–209
Kline WA, DeVor RE (1983) The effect of runout on cutting geometry and forces in end milling. International Journal of Machine Tool Design and Research 23(2–3):123–140
Vogler MP, DeVor RE, Kapoor SG (2004) On the modelling and analysis of machining performance in micro-endmilling, Part II: Cutting force prediction. Journal Manufacturing and Science Engineering 126(4):695–705
Zaman MT, Senthil Kumar A, Rahman M, Sreeram S (2006) A three-dimensional analytical cutting force model for micro end milling operation. Journal Machine Tools & Manufacture 46(3–4):353–366
Zheng HQ, Li XP, Wong YS, Nee AYC (1999) Theoretical modeling and simulation of cutting forces in face milling with cutter runout. International Journal Machine Tools & Manufacturing 39(12):2003–2018
Xl J, Altintas Y (2012) Prediction of micro-milling forces with finite element method. J Mater Process Technol 212(3):542–553
Afazov SM, Ratchev SM, Segal J (2010) Modelling and simulation of micro-milling cutting forces. J Mater Process Technol 210(15):2154–2162
Wang J-JJ (2003) Identification of cutter offset in end milling without a prior knowledge of cutting coefficients. International Journal Machine Tools & Manufacturing 43:687–697
Armarego EJA (1998) A generic mechanics of cutting approach to predictive technological performance modelling of the wide spectrum of machining perations, Proceeding of the CIRP International Workshop on Modelling of Machining Operations, Atlanta, Georgia, USA, 95–107
Jing XB, Li HZ, Wang J, Tian YL (2014) Modelling the cutting forces in micro-end-milling using a hybrid approach. Journal Advanced Manufacturing Technology 73(9):1647–1656
Zhang DL, Mo R, Chang ZY, Sun HB, Li CL (2016) A study of computing accuracy of calibrating cutting force coefficients and run-out parameters in flat-end milling. Journal Advanced Manufacturing Technology 84(1):621–630
Ko JH, Cho DW (2005) 3D ball-end milling force model using instantaneous cutting force coefficients. Journal Manufacturing and Science Engineering 127(1):1–12
Lee HU, Cho DW, Ehmann KF (2008) A mechanistic model of cutting forces in micro-end-milling with cutting-condition-independent cutting force coefficients. J Manuf Sci Eng 130(3):1–9
Li CF, Lai XM, Li HT, Ni J (2007) Modeling of three-dimensional cutting forces in micro-end-milling. J Micromech Microeng 17(4):671–678
Polini W, Prisco U (2003) The estimation of the diameter error in bar turning: a comparison among three cutting force models. Journal Advanced Manufacturing Technology 22(7):465–474
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Jing, X., Tian, Y., Yuan, Y. et al. A runout measuring method using modeling and simulation cutting force in micro end-milling. Int J Adv Manuf Technol 91, 4191–4201 (2017). https://doi.org/10.1007/s00170-017-0076-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0076-9