Abstract
Face milling is extremely popular in industrial mass production of spiral bevel and hypoid gears because of its high productivity and the superior contact performance of the gear pairs it produces. This method, however, includes many cutting systems that must be implemented on numerous dedicated traditional machines with differently designed mechanisms. The five-axis CNC machine, in contrast, has enough degrees of freedom to handle all these cutting systems. As a result, the use of a general five-axis machine to produce face-milled bevel gears is attracting growing attention because it is so much more flexible than dedicated machines in small-scale diverse production. This paper therefore proposes a face-milling system with flank correction for bevel gears on a five-axis CNC machine. First, a mathematical model of the tooth surface is established based on a trunnion table type machine, after which the five coordinates of the five-axis machine are derived using the machine settings of a virtual cradle type bevel gear cutting machine. These five coordinates are degenerated to a function of the generating angle, and each coordinate is approximated as a polynomial in a Maclaurin series. Because flank topographic errors can be systematically reduced by adjusting the polynomial coefficients, a flank correction technology is developed based on a sensitivity analysis that investigates flank topographic deviations in terms of changes in coefficients. Based on this sensitivity matrix and the tooth surface errors measured, corrections are made to the five-axis coefficients using the least squares method. Finally, following a program accuracy check using NC verification software, several cutting experiments are performed to verify the correctness of the mathematical models.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Litvin FL, Gutman Y (1981) Methods of synthesis and analysis for hypoid gear-drives of “formate” and “helixform”—part 1. Calculations for machine settings for member gear manufacture of the formate and helixform hypoid gears. ASME J Mech Des 103(1):83–88
Litvin FL, Gutman Y (1981) Methods of synthesis and analysis for hypoid gear-drives of “formate” and “helixform”—part 2. Machine setting calculations for the pinions of formate and helixform gears. ASME J. Mech. Des 103(1):89–101
Litvin FL, Gutman Y (1981) Methods of synthesis and analysis for hypoid gear-drives of “formate” and “helixform”—part 3. Analysis and optimal synthesis methods for mismatch gearing and its application for hypoid gears of “formate” and “helixform”. ASME J. Mech. Des 103(1):102–110
Litvin FL, Zhang Y, Lundy M, Heine C (1988) Determination of settings of a tilted dead cutter for generation of hypoid and spiral bevel gears. J Mech, Trans, and Automation 110(4):495–500
Fong ZH (2000) Mathematical model of universal hypoid generator with supplemental kinematic flank correction motions. ASME J. Mech. Des. 122(1):136–142
Shih YP, Fong ZH, Lin GCY (2007) Mathematical model for a universal face hobbing hypoid gear generator. ASME J. Mech. Des. 129(1):38–47
Deng XZ, Li GG, Wei BY, Deng J (2014) Face-milling spiral bevel gear tooth surfaces by application of 5-axis CNC machine tool. Int J Adv Manuf Tech 71(5):1049–1057
Shih YP, Lai KL, Sun ZH, Yan XL (2015) Manufacture of face-milled spiral bevel gears on a five-axis CNC machine. Paper presented at the 14th IFToMM World Congress, October 25–30, 2015, Taipei, Taiwan, DOI: 10.6567/IFToMM.14TH.WC.OS6.032
Litvin FL, Fuentes A (2004) Gear geometry and applied theory, second edn. Cambridge University Press, Cambridge
Shih YP, Fong ZH (2008) Flank correction for spiral bevel and hypoid gears on a six-axis CNC hypoid generator. ASME J Mech Des 130(6):062604
Gleason Works, (1971) Calculation instructions: generated spiral bevel gears, duplex-helical method, including grinding, Rochester, NY
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Shih, YP., Sun, ZH. & Lai, KL. A flank correction face-milling method for bevel gears using a five-axis CNC machine. Int J Adv Manuf Technol 91, 3635–3652 (2017). https://doi.org/10.1007/s00170-017-0032-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0032-8