Abstract
In order to improve the joint performances by controlling the thermal effect of tool shoulder, a non-shoulder-plunge (NSP) welding tool is utilized to conduct friction stir welding (FSW) of an Al-Mg aluminum alloy in this paper. Sound FSW joint is successfully produced by using the NSP welding tool. In contrast to conventional FSW (C-FSW), the thermal effect of tool shoulder is effectively reduced by NSP-FSW, leading to a significant size reduction of shoulder-affected zone in the joint. Besides, the NSP-FSW joint shows finer grain structures in the stir zone and thermo-mechanically affected zone, and exhibits lower extents of grain coarsening, dislocation polygonization, and particle dissolution in the heat-affected zone. Hardness maps show that the softening region width of NSP-FSW joint is only nearly half that of C-FSW joint and the NSP-FSW joint exhibits higher hardness in the heat-affected zone than C-FSW joint. The tensile test results indicate that the joint efficiency is improved from 89 % of C-FSW joint to 97 % by the NSP-FSW process.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Nandan R, Debroy T, Bhadeshia HKDH (2008) Recent advances in friction-stir welding—process, weldment structure and properties. Prog Mater Sci 53:980–1023
Cam G, Mistikoglu S (2014) Recent developments in friction stir welding of Al-alloys. J Mater Eng Perform 23:1936–1953
Schmidt H, Hattel J, Wert J (2004) An analytical model for the heat generation in friction stir welding. Model Simul Mater Sci Eng 12:143–157
Nandan R, Roy GG, Lienert TJ, Debroy T (2007) Three-dimensional heat and material flow during friction stir welding of mild steel. Acta Mater 55:883–895
Hilgert J, Schmidt HNB, dos Santos JF, Huber N (2011) Thermal models for bobbin tool friction stir welding. J Mater Process Technol 211:197–204
Fratini L, Buffa G, Shivpuri R (2010) Mechanical and metallurgical effects of in process cooling during friction stir welding of AA7075-T6 butt joints. Acta Mater 58:2056–2067
Liu HJ, Zhang HJ, Huang YX, Yu L (2010) Mechanical properties of underwater friction stir welded 2219 aluminum alloy. Trans Nonferrous Metals Soc China 20:1387–1391
Fu RD, Sun ZQ, Sun RC, Li Y, Liu HJ, Liu L (2011) Improvement of weld temperature distribution and mechanical properties of 7050 aluminum alloy butt joints by submerged friction stir welding. Mater Des 32:4825–4831
Papahn H, Bahemmat P, Haghpanahi M, Sommitsch C (2015) Study on governing parameters of thermal history during underwater friction stir welding. Int J Adv Manuf Technol 78:1101–1111
Ghetiya ND, Patel KM, Patel Anup B (2015) Prediction of temperature at weldline in air and immersed friction stir welding and its experimental validation. Int J Adv Manuf Technol 79:1239–1246
Elangovan K, Balasubramanian V, Babu S (2008) Developing an empirical relationship to predict tensile strength of friction stir welded AA2219 aluminum alloy. J Mater Eng Perform 17:820–830
Elangovan K, Balasubramanian V, Babu S (2009) Predicting tensile strength of friction stir welded AA6061 aluminium alloy joints by a mathematical model. Mater Des 30:188–193
Silva ACF, Braga DFO, de Figueiredo MAV, Moreira PMGP (2015) Ultimate tensile strength optimization of different FSW aluminium alloy joints. Int J Adv Manuf Technol 79:805–814
Ramulu PJ, Narayanan RG (2014) Influence of shoulder diameter, plunge depth, welding speed, rotational speed on the tensile behavior of friction stir welded AA 6061-T6 sheets. J Test Eval 42:1–13
Doude HR, Schneider JA, Nunes AC Jr (2014) Influence of the tool shoulder contact conditions on the material flow during friction stir welding. Metall MaterTrans A 45:4411–4422
Ramulu PJ, Narayanan RG, Kailas SV (2013) Forming limit investigation of friction stir welded sheets: influence of shoulder diameter and plunge depth. Int J Adv Manuf Technol 69:2757–2772
Zhang YN, Cao X, Larose S, Wanjara P (2012) Review of tools for friction stir welding and processing. Can Metall Q 51:250–261
Galvão I, Leal RM, Rodrigues DM, Loureiro A (2013) Influence of tool shoulder geometry on properties of friction stir welds in thin copper sheets. J Mater Process Technol 213:129–135
Jr LT, Heredia G, Rybicki D, Johannes LB (2015) Effect of tool shoulder features on defects and tensile properties of friction stir welded aluminum 6061-T6. J Mater Process Technol 219:271–277
Su JQ, Nelson TW, Mishra R, Mahoney M (2003) Microstructural investigation of friction stir welded 7050-T651 aluminum. Acta Mater 51:713–729
Prangnell PB, Heason CP (2005) Grain structure formation during friction stir welding observed by the “stop action technique”. Acta Mater 53:3179–3192
Attallah MM, Davis CL, Strangwood M (2007) Microstructure-microhardness relationships in friction stir welded AA5251. J Mater Sci 42:7299–7306
Amini S, Amiri MR, Barani A (2015) Investigation of the effect of tool geometry on friction stir welding of 5083-O aluminum alloy. Int J Adv Manuf Technol 76:255–261
Threadgill PL, Leonard AJ, Shercliff HR, Withers PJ (2009) Friction stir welding of aluminium alloys. Int Mater Rev 54:49–93
Liu HJ, Fujii H, Maeda M, Nogi K (2003) Tensile properties and fracture locations of friction-stir-welded joints of 2017-T351 aluminum alloy. J Mater Process Technol 142:692–696
Zhang HJ, Liu HJ, Yu L (2011) Microstructural evolution and its effect on mechanical performance of joint in underwater friction stir welded 2219-T6 aluminium alloy. Sci Technol Weld Join 16:459–464
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhang, H.J., Wang, M., Zhu, Z. et al. Improving the structure-property of aluminum alloy friction stir weld by using a non-shoulder-plunge welding tool. Int J Adv Manuf Technol 87, 1095–1104 (2016). https://doi.org/10.1007/s00170-016-8599-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-8599-z