Zusammenfassung
Das Stauchen einfacher axialsymmetrischer Proben wird mit Hilfe des Verfahrens von der oberen Schranke untersucht. Die angegebene numerische Methode, ein iteratives Ritz-Verfahren für mehrparametrige Ansatzfunktionen, liefert bessere Schranken für die Stauchkraft als vergleichbare Verfahren in der Literatur. Zudem erhält man eine gute Approximation des momentanen Geschwindigkeitsfeldes und kann damit den Verlauf der Umformung schrittweise verfolgen. Das angegebene Verfahren läßt sich durch Wahl geeigneter Ansatzfunktionen sinnvoll auf andere Umformprozesse anwenden.
Summary
The compression of simple axisymmetric specimen is treated by means of the upper bound theorem. An iterative Ritz-method, proposed in this paper, yields better upper bound loads than comparable methods known in literature. Moreover, a good approximation of the instantaneous velocity field is derived. Using this field the non-stationary deformation is examined step by step. By choosing a proper system of functions for the velocity field the given method well applies to other forming processes.
Article PDF
Avoid common mistakes on your manuscript.
Literatur
Lippmann, H., undO. Mahrenholtz: Plastomechanik der Umformung metallischer Werkstoffe. Berlin-Heidelberg-New York: Springer. 1966.
Siebel, E., undA. Pomp: Zur Weiterentwicklung des Druckversuches. Mitt. K. Wilh. Inst. Eisenforsch.10, 55–62 (1928).
Körber, F., undA. Eichinger: Die Grundlagen der bildsamen Formgebung. Mitt. K.Wilh.Inst. Eisenforsch.22, 57–80 (1940).
Unksow, E. P.: Ingenieurmethoden zur Berechnung der Kräfte bei der Metallbearbeitung unter Druck (russisch). Moskau: Masgiz. 1955.
Schroeder, W., undD. A. Webster: Press Forging Thin Sections: Effect of Friction, Area, and Thickness on Pressures Required. J. Appl. Mech.16, 289–294 (1949).
Hill, R.: The Mathematical Theory of Plasticity. Oxford: Clarendon Press. 1950.
Bishop, J. W. F.: On the Effect of Friction on Compression and Indentation between Flat Dies. J. Mech. Phys. Solids6, 132–144 (1958).
Kudo, H.: Analytical and Experimental Studies of Axi-symmetric cold Forging and Extrusion. Int. J. Mech. Sci.2, 102–127 (1960/61).
Kobayashi, S., undE. G. Thomsen: Upper and Lower Bound Solutions to Axisymmetric Compression and Extrusion Problems. Int. J. Mech. Sci.7, 127–143 (1965).
Collins, I. F.: The Upper Bound Theorem for Rigid/Plastic Solids Generalized to Include Coulomb Friction. J. Mech. Phys. Solids17, 323–338 (1969).
Hill, R.: A general Method of Analysis for Metal-working Processes. J. Mech. Phys. Solids11, 305–326 (1963).
Nagamatsu, A., T. Murota undT. Jimma: On the Non-Uniform Deformation of Material in Axially Symmetric Compression Caused by Friction. Bull. ISME14, 331–347 (1970).
Steck, E.: Numerische Behandlung von Verfahren der Umformtechnik. Berichte a. d. Institut für Umformtechnik, Universität Stuttgart. Heft22 (1971).
Sauer, R., undI. Szabó: Mathematische Hilfsmittel des Ingenieurs, Teil III. Berlin-Heidelberg-New York: Springer. 1968.
Liu, J. Y.: Upper-Bound Solutions of Some Axisymmetric Cold Forging Problems. J. Eng. Ind.93, 1134–1144 (1971).
Kachanov, L. M.: Foundations of the Theory of Plasticity. Amsterdam: North Holland. 1971.
Author information
Authors and Affiliations
Additional information
Mit 7 Abbildungen
Rights and permissions
About this article
Cite this article
Andresen, K. Die numerische Behandlung eines Schrankenverfahrens mit Anwendung auf axialsymmetrisches Stauchen. Acta Mechanica 17, 291–303 (1973). https://doi.org/10.1007/BF01183762
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF01183762