Abstract
We investigate the nonlinear dynamics of a hybrid electro-optomechanical system (EOMS) that allows us to realize the controllable opto-mechanical nonlinearity by driving the microwave LC resonator with a tunable electric field. A controllable optical chaos is realized even without changing the optical pumping. The threshold and lifetime of the chaos could be optimized by adjusting the strength, frequency, or phase of the electric field. This study provides a method of manipulating optical chaos with an electric field. It may offer the prospect of exploring the controllable chaos in on-chip optoelectronic devices and its applications in secret communication.
Similar content being viewed by others
Introduction
Cavity optomechanics has attracted wide interests in the fields of quantum optics and nonlinear optics in the past a few years1,2,3,4,5,6,7,8. It explores the intrinsic radiation-pressure interaction between the optical and mechanical modes in the cavity optomechanical system (OMS). Focusing on the classical domain, the nonlinear opto-mechanical interaction can make the mechanical oscillator enter into the regime of self-induced oscillations9,10,11,12,13, where the backaction-induced mechanical gain overcomes mechanical loss, under the condition of blue-detuned driving. Increasing the driving strength, chaotic motion emerges both in the optical and mechanical modes14,15,16,17,18. It is shown that this chaos originally comes from the intrinsic optomechanical nonlinearity and does not need periodic perturbation, external feedback, modulation, or delay. This is useful for generating random numbers19 and implementing secret information processing20,21,22. However, to apply the generated chaotic signal into the secret communication scheme, good controllability and design flexibility are necessary23,24.
Hybrid electro-optomechanical system (EOMS)25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40 contains a mechanical oscillator coupled to both an optical cavity and a microwave LC resonator (see Fig. 1) and offers an alternative platform for controlling the optical signal via an electric field. The mechanical oscillator in the EOMS acts as a quantum or classical interface between the optical and microwave modes. Theoretically, it is possible to realize the electric-controlled optomechanically induced transparency29, optical nonlinearity35 and quantum state transfer between an optical and microwave modes30,32,34 based on this phonon-interface in the hybrid EOMS. Recently, the hybrid EOMS also has been realized experimentally41,42,43, which will inspire the further investigations regarding its basic physical property and the corresponding applications. A natural question is whether we could realize the electric-controlled optical chaos in the hybrid EOMS by using its phonon-interface, which has potential applications in implementing on-chip secret communication.
Here we propose a method to realize the controllable optical chaos in a hybrid EOMS consisting a mechanical oscillator coupled to both an optical cavity and a microwave LC resonator. The microwave resonator is driven by a tunable electric field, which acts as a control part and is separated from the generation part of the chaotic signal. Comparing with the normal OMS, the opto-mechanical nonlinearity in the hybrid EOMS is controllable without changing the optical pumping. Then the switching between the periodic and chaotic motions of the optical field could be realized by only adjusting the electric driving field. Physically, the opto-mechanical nonlinearity will be changed when one drives the LC resonator under different conditions. This ultimately leads to the fact that the chaotic threshold, degree and lifetime are controllable with respect to an electric field. This study provides a new avenues of manipulating the chaotic signal in on-chip optoelectronic devices and could effectively avoid the crosstalk between the control field and the chaotic signal in the single-cavity OMS.
Results
Hybrid electro-optomechanical system
We consider a hybrid EOMS depicted in Fig. 1, a mechanical oscillator couples to both an optical cavity and a LC resonator with coupling strengths ħga and ħgc. In our proposal, the EOMS is in the weak coupling regime and the values of ga and gc have been chosen according to the optomechanical experiment44. The microwave resonator (with frequency ) acts as the control port and is driven by a tunable electric field with amplitude Ωc and frequency ωlc. Here Ωc is related to the input microwave power Pc and decay rate κc by . The optical cavity (with frequency ωa) acts as the generation port of chaotic signal and is pumped by a fixed laser with amplitude Ωa and frequency ωla. Here Ωa is related to the input optical power Pa and decay rate κa by . In a frame rotating with frequencies ωla, ωlc, the Hamiltonian for this hybrid system reads
where , are the corresponding annihilation (creation) operators of the optical and microwave fields and Δa = ωa − ωla (Δc = ωc − ωlc) is the frequency detuning between the optical cavity (microwave resonator) and the pumping laser (driving electric field). We also have used , to denote the displacement and momentum of the mechanical oscillator. Here the relative phase ϕ between the control and pumping fields is retained since the chaotic motion is usually sensitive to the initial conditions of system.
Generally, the optomechanical interaction in Eq. (1) (i.e., ) can lead to the chaotic motions of the optical and mechanical modes at a very high-power laser-pumping (~10 milliwatt) in the normal single-cavity OMS14. However, here we will demonstrate the generation of the optical chaos in a “weak” pumping regime, i.e., the pumping power Pa = 0.5 mW, which is well below the threshold of chaos in an single-cavity OMS for almost 2 order. Moreover, in our proposal, the mechanical oscillator in the hybrid EOMS couples to both an optical cavity and a microwave resonator. This effectively separates the control and generation ports of the chaotic signal and increases the controllability of the chaos generation. To present this controllability, in the following sections, we explore the nonlinear dynamics of system by numerically calculating Eqs (2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13) of the Methods. Note that here the electric driving field is tunable and the optical pumping field is fixed. We define as the intensity of the optical cavity, whose spectrum S(ω) can be got by using fast Fourier transform.
Dependence of system dynamics on control-field-power
First of all, in Fig. 2, we present the evolutions of the intensity I, the power spectrum LnS(ω) of the intracavity field as well as the optical trajectories in phase space (i.e., the first derivation of I versus I) under different powers of the control field. It shows that the system dynamics experiences regular to chaotic behaviors when one increases the power Pc of the control field from 5.79 μW to 13 μW. The power spectrum of I goes through period, period doubling to a continuum as increasing Pc, which characterizes the route to chaos. Accordingly, the optical trajectories in phase space are limited into the regular circles with periodically varying radius under the condition of weak driving and they become more and more complicated in the strong-driving-regime. The above results show that the generation of the optical chaos can be controlled by adjusting the power of an electric-control-field, which does not interact with the optical cavity.
To further explore the influence of Pc on the chaotic dynamics, we present the evolution of a nearby point of I (i.e., I + εI shown in Methods) in Fig. 3. The calculated exponential variation of εI indicates how the states of intracavity field vary in temporal domain and phase space. Specifically, the decrease of Ln(εI) over time indicates that all the nearby points of I in phase space will finally oscillate in the limited circles. The flat evolution of Ln(εI) implies the period-doubling bifurcation. The exponential divergence of Ln(εI) corresponds to the chaotic dynamics, which reveals that the chaotic regime is extremely sensitive to initial conditions. Figure 3 presents that enhancing the driving power could increase the lifetimes of chaos, which is denoted by τ1, τ2, τ3 and defined by the last time of the chaotic motion and the degree of chaos corresponding the gradients of Ln(εI).
Dependence of system dynamics on driving frequency
In our proposal, another tunable system parameter is the frequency ωlc of the electric driving field. In Fig. 4, we present the influence of the frequency detuning Δc (Δc = ωc − ωlc) on the system dynamics, characterized by the evolutions of I, the power spectrum LnS(ω) and the optical trajectories in phase space. It shows that the optical trajectory changes to chaotic motion from periodic motion going by the period-doubling when we adjust Δc from blue-detuning to red-detuning. In other words, the red-detuning favors the chaotic dynamics, which is different from the case in the single-mode OMS. Physically, here the optical chaos originally comes from the opto-mechanical nonlinearity, which is decided by the excitation of the mechanical oscillator. The mechanical oscillator is easily excited when the electromechanical subsystem is driven under the condition of red-detuning. Moreover, in Fig. 5, we also present the evolution of a nearby point (I + εI) of I under the condition of blue- and red-detuning driving. The exponential divergence of Ln(εI) under the condition of red-detuning displays the same conclusion. The red-detuning driving could enhance the opto-mechanical nonlinearity and lead to the generation of chaos with the lower optical threshold.
Dependence of system dynamics on relative phase
Now let’s discuss the influence of the relative phase ϕ on the system dynamics (see Fig. 6). Here the relative phase is defined as ϕ = ϕc − ϕa and ϕc (ϕa) is the phase of the electric driving (optical pumping) field. It is shown that the chaotic lifetime (denoted by τj) is periodically changed when ϕ is tuned in the range of 0 to 2π. For example the lifetime of chaos increases from ϕ = 0 to ϕ = 2π/3. However it decreases from ϕ = 2π/3 to 8π/5. This result originally comes from the periodic dependence of the opto-mechanical nonlinearity on the relative phase ϕ. Such feature provides a new route to manipulate the chaotic signal.
Before finishing this section, to illustrate the influences of system parameters on the chaotic dynamics more clearly, we present the dependence of the Lyapunov exponents on the driving power Pc, the frequency detuning Δc and the relative phase ϕ in Fig. 7. Here the Lyapunov exponent is defined by the logarithmic slope of the perturbation εI versus time t and characterizes the separation of trajectories for the identical systems with infinitesimally close initial condition. The negative (positive) value of Lyapunov exponent indicates that the dynamics of system is periodical (chaotic). The dynamical evolution of system exhibits a period doubling behavior when the value of Lyapunov exponent is equal to zero. In Fig. 7(a), the Lyapunov exponent increases (from negative to positive) with enhancing the strength of the control field. This clearly shows the emergence of chaos under the condition of strong electric driving (Pc > 4.5 μW) and it is consistent with the numerical results in Fig. 2. However, Fig. 7(b) indicates that the influence of frequency detuning Δc on the optical chaos is not so simple as exhibited in Fig. 4. The optical chaos emerges periodically with increasing Δc. This periodic behavior can also be found in the dependence of chaos on ϕ, i.e., Fig. 7(c). Physically, in the hybrid EOMS, the mechanical displacement amplitude q is dependent periodically on the frequency (corresponding to Δc) and phase (corresponding to ϕ) of the electric driving-field. It corresponds to a periodical enhancement of the opto-mechanical nonlinearity, which ultimately leads to the fact that the chaotic degree dependents periodically on Δc and ϕ.
To explore the role of the optical pump laser, in Fig. 8, we present the dependence of Lyapunov exponent on Pa in the normal OMS and our model, respectively. It clearly shows that the chaotic motion emerges (Lyapunov exponent > 0) when the pumping power Pa > Poth (Poth is defined by the optical pumping power corresponding to the Lyapunov exponent equal to zero). More interestingly, comparing with the normal OMS, the optical threshold Poth of chaos is reduced almost two order in our proposal. Physically, this is due to the opto-mechanical nonlinearity is enhanced when the electricmechanical subsystem is driven with an electric field. This result provides an alternative method to decrease the chaotic threshold in the OMS. Lastly, it should be noted that, in Figs 7 and 8, a non-zero optical (or electrical) driving power has been chosen, i.e., Pa = 0.5 mW (or Pc = 10 μW), which induces a considerable opto-mechanical nonlinearity even without the electrical (or optical) driving-field. This retained opto-mechanical nonlinearity leads to the result that the dynamics of system enters easily into the chaotic regime and then the Lyapunov exponents are almost non-negative in the chosen parameter range of Figs 7 and 8.
Discussion
We have presented a practical method to achieve the controllable optical chaos in a hybrid EOMS. Via investigating the nonlinear dynamics of system, we shown that the optical chaos could be switched on and off by driving the electromechanical subsystem with a tunable electric field. This is due to that the opto-mechanical nonlinearity (the essence of the generation of chaos) can be controlled by an electric field in the hybrid EOMS. We analyzed in detail the influences of the frequency, strength and phase of the electric control field on the chaotic dynamics, including the degree and the lifetime of chaos. Moreover, we also shown that the optical threshold of chaos is reduced dramatically in our model due to the enhanced opto-mechanical nonlinearity when the electromechanical subsystem is driven. This study provides a promising route for controlling the optical nonlinear dynamics, especially the generation of the optical chaos, with an electric field and has potential applications in implementing secret communication on the integrated chips.
Methods
To explore the nonlinear dynamics of system, we employ the semiclassical equations of motion (setting , is any optical or mechanical operator)
where γm is the damping rate of the mechanical oscillator and we have defined a = ar + iai, c = cr + ici (ar, ai, cr, ci are real numbers) for simplifying the discussion of the chaotic property of system. Therefore, the Eqs (2, 3, 4, 5, 6, 7) are given by splitting the real and imaginary parts into different equations. Here the quantum correlations of photon-phonon have been safely ignored in the semiclassical approximation, which is valid in the concerned weak-coupling regime14. Eqs (2, 3, 4, 5, 6, 7) show that the intracavity field intensities and the mechanical deformation influence each other during the system evolution via the optomechanical interaction. Specifically, Eqs (2) and (3) describe the motion of mechanical oscillator and Eqs (4, 5, 6, 7) describe the dynamics of the optical and microwave modes. The quadratic terms and in Eq. (3) and the mixed terms −gaqai, gaqar and −gcqci, gcqcr in Eqs (4, 5, 6, 7) clearly present the nonlinear interaction between the optical (or microwave) and the mechanical modes.
To calculate the Lyapunov exponent of the dynamical evolution, we linearize Eqs (2, 3, 4, 5, 6, 7) and introduce the evolution of a perturbation ,
which characterizes the divergence of nearby trajectories in phase space. Here we define and use its logarithm Ln(εI) to show the tendency of the perturbation. Then the logarithmic slope of the perturbation εI versus time t is defined as Lyapunov exponent, the negative and positive values of the Lyapunov exponent, respectively denotes states of the dynamical system, being out of and in the chaotic motions.
Additional Information
How to cite this article: Wang, M. et al. Controllable chaos in hybrid electro-optomechanical systems. Sci. Rep. 6, 22705; doi: 10.1038/srep22705 (2016).
References
Aspelmeyer, M., Kippenberg, T. J. & Marquardt, F. Cavity optomechanics. Rev. Mod. Phys. 86, 1391 (2014).
Aspelmeyer, M., Meystre, P. & Schwab, K. Quantum optomechanics. Phys. Today 65(7), 2935 (2012).
Meystre, P. A short walk through quantum optomechanics. Ann. Phys. 525, 215 (2013).
Marquardt, F. & Girvin, S. M. Optomechanics (a brief review). Physics 2, 40 (2009).
Kippenberg, T. J. & Vahala, K. J. Cavity optomechanics: back-action at the mesoscale. Science 321, 1172 (2008).
Xiong, H., Si, L.-G., Lü, X.-Y., Yang, X.-X. & Wu, Y. Review of cavity optomechanics in the weak-coupling regime: from linearization to intrinsic nonlinear interactions. Sci. China Phys., Mech. Astron. 58, 1–13 (2015).
Sun, C.-P. & Li, Y. Special Topic: Optomechanics. Sci. China Phys., Mech. Astron. 58, 050300 (2015).
Yin, Z. Q., Zhao, N. & Li, T. C. Hybrid opto-mechanical systems with nitrogen-vacancy centers. Sci. China Phys., Mech. Astron. 58, 050303 (2015).
Kippenberg, T. J., Rokhsari, H., Carmon, T., Scherer, A. & Vahala, K. J. Analysis of radiation-pressure induced mechanical oscillation of an optical microcavity. Phys. Rev. Lett. 95, 033901 (2005).
Carmon, T., Rokhsari, H., Yang, L., Kippenberg, T. J. & Vahala, K. J. Temporal behavior of radiation-pressure-induced vibrations of an optical microcavity phonon mode. Phys. Rev. Lett. 94, 223902 (2005).
Marquardt, F., Harris, J. G. E. & Girvin, S. M. Dynamical multistability induced by radiation pressure in high-finesse micromechanical optical cavities. Phys. Rev. Lett. 96, 103901 (2006).
Metzger, C. et al. Self-induced oscillations in an optomechanical system driven by bolometric backaction. Phys. Rev. Lett. 101, 133903 (2008).
Zaitsev, S., Pandey, A. K., Shtempluck, O. & Buks, E. Forced and self-excited oscillations of an optomechanical cavity. Phys. Rev. E 84, 046605 (2011).
Carmon, T., Cross, M. C. & Vahala, K. J. Chaotic quivering of micron-scaled on-chip resonators excited by centrifugal optical pressure. Phys. Rev. Lett. 98, 167203 (2007).
Zhang, K., Chen, W., Bhattacharya, M. & Meystre, P. Hamiltonian chaos in a coupled BEC-optomechanical-cavity system. Phys. Rev. A 81, 013802 (2010).
Larson, J. & Horsdal, M. Photonic Josephson effect, phase transitions and chaos in optomechanical systems. Phys. Rev. A 84, 021804(R) (2011).
Ma, J. et al. Formation and manipulation of optomechanical chaos via a bichromatic driving. Phys. Rev. A 90, 043839 (2014).
Bakemeier, L., Alvermann, A. & Fehske, H. Route to chaos in optomechanics. Phys. Rev. Lett. 114, 013601 (2015).
Gleeson, J. T. Truly random number generator based on turbulent electroconvection. Appl. Phys. Lett. 81, 1949 (2002).
Sivaprakasam, S. & Shore, K. A. Signal masking for chaotic optical communication using external-cavity diode lasers. Opt. Lett. 24, 466 (1999).
VanWiggeren, G. D. & Roy, R. Communication with chaotic lasers. Science 279, 1198 (1998).
Sciamanna, M. & Shore, K. A. Physics and applications of laser diode chaos. Nat. Photonics 9, 151 (2015).
Miller, D. Device requirements for optical interconnects to silicon chips. Proc. IEEE 97, 1166 (2009).
Ellis, B. et al. Ultralow-threshold electrically pumped quantum-dot photonic-crystal nanocavity laser. Nat. Photonics 5, 297 (2011).
Regal, C. A. & Lehnert, K. W. From cavity electromechanics to cavity optomechanics. J. Phys. Conf. Ser.264, 012025 (2011).
Winger, M. et al. A chip-scale integrated cavity-electro-optomechanics platform. Opt. Express 19, 24905 (2011).
Tsang, M. Cavity quantum electro-optics. II. Input-output relations between traveling optical and microwave fields. Phys. Rev. A 84, 043845 (2011).
Barzanjeh, S., Vitali, D., Tombesi, P. & Milburn, G. J. Entangling optical and microwave cavity modes by means of a nanomechanical resonator. Phys. Rev. A 84, 042342 (2011).
Qu, K. & Agarwal, G. S. Phonon-mediated electromagnetically induced absorption in hybrid opto-electromechanical systems. Phys. Rev. A 87, 031802(R) (2013).
Wang, Y.-D. & Clerk, A. A. Using Interference for High Fidelity Quantum State Transfer in Optomechanics. Phys. Rev. Lett. 108, 153603 (2012).
Wang, Y.-D. & Clerk, A. A. Reservoir-engineered entanglement in optomechanical systems. Phys. Rev. Lett. 110, 253601 (2013).
Tian, L. Adiabatic State Conversion and Pulse Transmission in Optomechanical Systems. Phys. Rev. Lett. 108, 153604 (2012).
Tian, L. Robust photon entanglement via quantum interference in optomechanical interfaces. Phys. Rev. Lett. 110, 233602 (2013).
Barzanjeh, Sh., Abdi, M., Milburn, G. J., Tombesi, P. & Vitali, D. Reversible Optical-to-Microwave Quantum Interface. Phys. Rev. Lett. 109, 130503 (2012).
Lü, X.-Y., Zhang, W.-M., Ashhab, S., Wu, Y. & Nori, F. Quantum-crtically-induced strong Kerr nonlinearities in optomechanical systems. Sci. Rep. 3, 2943 (2013).
Zhang, J.-Q., Li, Y., Feng, M. & Xu, Y. Precision measurement of electrical charge with optomechanically induced transparency. Phys. Rev. A 86, 053806 (2012).
Guo, Y., Li, K., Nie, W. & Li, Y. Electromagnetically-induced-transparency-like ground-state cooling in a double-cavity optomechanical system. Phys. Rev. A 90, 053841 (2014).
Palomaki, T. A., Teufel, J. D., Simmonds, R. W. & Lehnert, K. W. Entangling mechanical motion with microwave fields. Science 342, 710 (2013).
He, Q. & Ficek, Z. Einstein-Podolsky-Rosen paradox and quantum steering in a three-mode optomechanical system. Phys. Rev. A 89, 022332 (2014).
Barzanjeh, S. et al. Microwave Quantum Illumination. Phys. Rev. Lett. 114, 080503 (2015).
Bochmann, J., Vainsencher, A., Awschalom, D. D. & Cleland, A. N. Nanomechanical coupling between microwave and optical photons. Nat. Physics 9, 712 (2013).
Andrews, R. W. et al. Bidirectional and efficient conversion between microwave and optical light. Nat. Physics 10, 321 (2014).
Xiang, Z.-L., Ashhab, S., You, J. Q. & Nori, F. Hybrid quantum circuits: Superconducting circuits interacting with other quantum systems. Rev. Mod. Phys. 85, 623 (2013).
Weis, S. et al. Optomechanically Induced Transparency. Science 330, 1520 (2010).
Acknowledgements
The work was supported by the National Natural Fundamental Research Program of China (Grant No. 2012CB922103), the National Science Foundation of China (Grant Nos. 11374116, 11375067, 11275074, 11204096, 11405061 and 11574104).
Author information
Authors and Affiliations
Contributions
M.W. carried out all calculations under the guidance of X.-Y.L. and Y.W. J.-Y.M., H.X. and L.-G.S. participated in the discussions. All authors contributed to the interpretation of the work and the writing of the manuscript.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Wang, M., Lü, XY., Ma, JY. et al. Controllable chaos in hybrid electro-optomechanical systems. Sci Rep 6, 22705 (2016). https://doi.org/10.1038/srep22705
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep22705
- Springer Nature Limited
This article is cited by
-
Optomechanically induced tunable ideal nonreciprocity in optomechanical system with Coulomb interaction
Quantum Information Processing (2022)
-
Two-color second-order sideband generation in an optomechanical system with a two-level system
Scientific Reports (2018)
-
Reconfigurable chaos in electro-optomechanical system with negative Duffing resonators
Scientific Reports (2017)
-
Mesoscopic chaos mediated by Drude electron-hole plasma in silicon optomechanical oscillators
Nature Communications (2017)