Abstract
This study attempted to measure three cutting force components simultaneously for prismatic parts and determine the force-time characteristics until face turning was finished. A calibrated dynamometer was used in the turning experiments. The experiments for the aluminum alloy and brass workpieces were performed at different side cutting edge angles (SCEAs) for three different spindle speeds. The turning finishing processes of the prismatic parts were also monitored successfully. The cutting speed had a remarkable effect on the quality of data acquisition, but the SCEA did not. The scatter width of all forces increased with decreasing cutting speed, but the SCEA was not effective. Three forces generally exhibited familiar characteristic with increment in the SCEA for aluminum and brass workpieces. Furthermore, the cutting force amplitudes were perceived to be higher in cylindrical machining regions than impact machining regions. The \({F}_{\mathrm{c}}\) and \({F}_{\mathrm{r}}\) indicated similar self-trends for both metals during total machining processes.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Yaldiz, S.; Unsacar, F.: A dynamometer design for measurement the cutting forces on turning. Measurement 39(1), 80–89 (2006)
Korkut, I.: A dynamometer design and its construction for milling operation. Mater. Des. 24(8), 631–637 (2003)
Gunay, M.; Aslan, E.; Korkut, I.; Seker, U.: Investigation of the effect of rake angle on main cutting force. Int. J. Mach. Tool Manuf. 44(9), 953–959 (2004)
Gunay, M.; Korkut, I.; Aslan, E.; Seker, U.: Experimental investigation of the effect of cutting tool rake angle on main cutting force. J. Mater. Process. Technol. 166(1), 44–49 (2005)
Gunay, M.; Seker, U.; Sur, G.: Design and construction of a dynamometer to evaluate the influence of cutting tool rake angle on cutting forces. Mater. Des. 27(10), 1097–1101 (2006)
Radovanovic, M.; Dasic, P.; Jankovic, P.: Experimental determination of cutting force by longitudinal turning of C60E steel. Rom. Tech. Sci. Acad. 2, 113–119 (2006)
Saglam, H.; Unsacar, F.; Yaldiz, S.: Investigation of the effect of rake angle and approaching angle on main cutting force and tool tip temperature. Int. J. Mach. Tool Manuf. 46(2), 132–141 (2006)
Saglam, H.; Yaldiz, S.; Unsacar, F.: The effect of tool geometry and cutting speed on main cutting force and tool tip temperature. Mater. Des. 28(1), 101–111 (2007)
Bajic, D.; Lela, B.; Cukor, G.: Examination and modelling of the influence of cutting parameters on the cutting force and the surface roughness in longitudinal turning. Stroj Vestn-J. Mech. E 54(5), 322–333 (2008)
Thiele, J.D.; Melkote, S.N.: Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel. J. Mater. Process. Technol. 94(2–3), 216–226 (1999)
Lin, W.S.; Lee, B.Y.; Wu, C.L.: Modeling the surface roughness and cutting force for turning. J. Mater. Process. Technol. 108(3), 286–293 (2001)
Habalı, K.; Gökkaya, H.; Sert, H.: Experimental investigation of the effects of cutting tool coating materials on surface roughness in machining of AISI 1040 steel. J. Polytech. 9(1), 35–38 (2006)
Nalbant, M.; Altin, A.; Gokkaya, H.: The effect of coating material and geometry of cutting tool and cutting speed on machinability properties of Inconel 718 super alloys. Mater Design 28(5), 1719–1724 (2007)
Korkut, I.; Boy, M.: Experimental examination of main cutting force and surface roughness depending on cutting parameters. Stroj Vestn-J. Mech. E 54(7–8), 531–538 (2008)
Asano, K.: Turning machinability of short alumina fiber reinforced aluminum alloy composite using carbide tool. Mater. Trans. 56(7), 1120–1126 (2015)
Dinesh, S.; Senthilkumar, V.; Asokan, P.; Arulkirubakaran, D.: Effect of cryogenic cooling on machinability and surface quality of bio-degradable ZK60 Mg alloy. Mater. Des. 87, 1030–1036 (2015)
Razavykia, A.; Farahany, S.; Yusof, N.M.: Evaluation of cutting force and surface roughness in the dry turning of Al–Mg\(_{2}\)i in-situ metal matrix composite inoculated with bismuth using DOE approach. Measurement 76, 170–182 (2015)
Liu, X.W.; Cheng, K.; Webb, D.; Luo, X.C.: Prediction of cutting force distribution and its influence on dimensional accuracy in peripheral milling. Int. J. Mach. Tool Manuf. 42(7), 791–800 (2002)
Topal, E.S.; Cogun, C.: A cutting force induced error elimination method for turning operations. J. Mater. Process. Technol. 170(1–2), 192–203 (2005)
Cakir, M.C.; Isik, Y.: Detecting tool breakage in turning AISI 1050 steel using coated and uncoated cutting tools. J. Mater. Process. Technol. 159(2), 191–198 (2005)
Denkena, B.; Lucas, A.; Bassett, E.: Effects of the cutting edge microgeometry on tool wear and its thermomechanical load. CIRP Ann. Manuf. Technol. 60(1), 73–76 (2011)
Karpuschewski, B.; Schmidt, K.; Beno, J.; Mankova, I.; Frohmuller, R.; Prilukova, J.: An approach to the microscopic study of wear mechanisms during hard turning with coated ceramics. Wear 342, 222–233 (2015)
Lin, H.S.; Wang, C.Y.; Yuan, Y.H.; Chen, Z.H.; Wang, Q.M.; Xiong, W.Q.: Tool wear in Ti–6Al–4V alloy turning under oils on water cooling comparing with cryogenic air mixed with minimal quantity lubrication. Int. J. Adv. Manuf. Technol. 81(1–4), 87–101 (2015)
Milfelner, A.; Cus, F.; Balic, J.: An overview of data acquisition system for cutting force measuring and optimization in milling. J. Mater. Process. Technol. 164, 1281–1288 (2005)
Kong, M.C.; Axinte, D.A.; Wilson, B.; Marinescu, I.; Allen, J.; Raffles, M.; Weston, S.: An innovative design of multi-task dynamometers for turning operations. Proc. Inst. Mech. Eng. B J. Eng. 226(B6), 1118–1124 (2012)
Ayomoh, M.K.O.; Abou-EI-Hossein, K.A.; Olufayo, O.A.: Cutting force prediction for single point diamond tool-tip. In: 2013 6th Robotics and Mechatronics Conference (Robmech), pp. 123–128 (2013)
Teti, R.; Jemielniak, K.; O’Donnell, G.; Dornfeld, D.: Advanced monitoring of machining operations. CIRP Ann. Manuf. Technol. 59(2), 717–739 (2010). https://doi.org/10.1016/j.cirp.2010.05.010
Yaldiz, S.; Unsacar, F.: Design, development and testing of a turning dynamometer for cutting force measurement. Mater. Des. 27(10), 839–846 (2006). https://doi.org/10.1016/j.matdes.2005.04.001
Panzera, T.H.; Souza, P.R.; Rubio, J.C.C.; Abrao, A.M.; Mansur, T.R.: Development of a three-component dynamometer to measure turning force. Int. J. Adv. Manuf. Technol. 62(9–12), 913–922 (2012). https://doi.org/10.1007/s00170-011-3866-5
Zhao, Y.; Zhao, Y.L.; Liang, S.B.; Zhou, G.W.: A high performance sensor for triaxial cutting force measurement in turning. Sensors Basel 15(4), 7969–7984 (2015). https://doi.org/10.3390/s150407969
Hanif, M.I.; Aamir, M.; Muhammad, R.; Ahmed, N.; Maqsood, S.: Design and development of low cost compact force dynamometer for cutting forces measurements and process parameters optimization in turning applications. Int. J. Innov. Sci. 3(9), 306–3016 (2015)
Öztürk, E.; Yıldızlı, K.: A new static calibration methodology for strain gage integrated dynamometers. Int. J. Adv. Manuf. Technol. 91(5), 1823–1838 (2017)
Bouzakis, K.D.; Michailidis, N.; Skordaris, G.; Bouzakis, E.; Biermann, D.; M’Saoubi, R.: Cutting with coated tools: coating technologies, characterization methods and performance optimization. CIRP Ann. Manuf. Technol. 61(2), 703–723 (2012)
Kurt, A.; Yalcin, B.; Yilmaz, N.: The cutting tool stresses in finish turning of hardened steel with mixed ceramic tool. Int. J. Adv. Manuf. Technol. 80(1–4), 315–325 (2015)
Nalbant, M.; Altin, A.; Gokkaya, H.: The effect of cutting speed and cutting tool geometry on machinability properties of nickel-base Inconel 718 super alloys. Mater. Des. 28(4), 1334–1338 (2007)
Dorlin, T.; Fromentin, G.; Costes, J.P.: Analysis and modelling of the contact radius effect on the cutting forces in cylindrical and face turning of Ti6Al4V titanium alloy. Proc. CIRP 31, 185–190 (2015). https://doi.org/10.1016/j.procir.2015.03.017
Su, Y.; Li, Z.; Li, L.; Wang, J.; Gao, H.; Wang, G.: Cutting performance of micro-textured polycrystalline diamond tool in dry cutting. J. Manuf. Process. 27, 1–7 (2017). https://doi.org/10.1016/j.jmapro.2017.03.013
Cui, X.B.; Zhao, J.; Zhou, Y.H.; Pei, Z.Q.: Cutting forces and tool wear in intermittent turning processes with Al\(_{2}\)O\(_{3}\)-based ceramic tools. Key Eng. Mater. 499, 205–210 (2012). https://doi.org/10.4028/www.scientific.net/KEM.499.205
Gutnichenko, O.; Agic, A.; Stahl, J.E.: Modeling of force build-up process and optimization of tool geometry when intermittent turning. In: 16th CIRP Conference on Modelling of Machining Operations (16th Cirp Cmmo), vol. 58, pp. 393–398 (2017). https://doi.org/10.1016/j.procir.2017.03.241
Pressure gauges. https://dir.indiamart.com/impcat/electrical-pressure-gauges.html. Accessed 18 Apr 2017
Günay, M.: Talaş Kaldırma İşlemlerinde Kesici Takım Talaş Açısının Kesme Kuvvetlerine Etkisinin Deneysel Olarak İncelemesi. Gazi University (2003)
Öztürk, E.: Prizmatik Parçaların İşlenmesinde Kesme Kuvvetlerinin Analizi. Ondokuz Mayıs University (2015)
Acknowledgements
This study was financially supported by the Turkish Council of Higher Education under scholar grant: ÖYP-1919-020. The authors thank “Samsun Ilkadim Teknik ve Endüstri Meslek Lisesi” for using their facilities in our experiments. Special thanks to Nurettin ÜSTKOYUNCU, assistant professor at Electric Electronical Engineering, Department of Erciyes University, for his contributions of the strain gage based dynamometer design.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Öztürk, E., Yıldızlı, K. Measured Cutting Forces in the Turning of Prismatic Parts at Different Spindle Speeds and Side Cutting Edge Angles. Arab J Sci Eng 43, 4635–4647 (2018). https://doi.org/10.1007/s13369-017-3002-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13369-017-3002-4