Abstract
In the conventional 2D-FFT based target detection method, all range-Doppler cells are computed by FFT (Fast Fourier Transform) and scanned by CA-CFAR (Cell-Averaging Constant False Alarm Rate) detection. This results in high computational complexity and long processing time. In this paper, we developed an automotive 24 GHz BSD (Blind Spot Detection) FMCW (Frequency Modulated Continuous Wave) radar with a low complexity target detection architecture based on a ROI (Region Of Interest) pre-processing scheme. In the real BSD zone, because the number of cars to be detected is limited, the designed method only extracts their velocities corresponding to the range ROIs in which real targets exist. Moreover, the presence probability of vehicles with the same range-bin but different velocities is very low. Thus, in the designed method, some Doppler ROIs cells with a high magnitude are only applied for CA-CFAR detection. This architecture can dramatically reduce the amount of data to be processed compared to that of the conventional 2D FFT based method, resulting in enhanced processing time. We developed a 24 GHz FMCW radar system composed a transceiver, antennas, and signal processing module. The designed algorithm was implemented in a tiny micro-processor of the signal processing module. By implementing our proposed algorithm in the developed 24 GHz FMCW radar system in an anechoic chamber and a real road, we verified that the range and velocity of a car occupying the BSD zone were detected. Compared to that of the conventional method, the reduction ratio of the total processing time was measured to be 52.4 %.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
Bassem, R. M. and Atef, Z. E. (2004). Simulation for Radar Systems Design. Chapman & Hall/CRC. London, UK.
Fernández, C., Llorca, D. F., Sotelo, M. A., Daza, I. G., Hellín, A. M. and Álvarez, S. (2013). Real-time visionbased blind spot warning system: Experiments with motorcycles in daytime/nighttime conditions. Int. J. Automotive Technology 14, 1, 113–122.
Forkenbrock, G., Hoover, R. L., Gerdus, E., Van Buskirk, T. R. and Heitz, M. (2014). Blind Spot Monitoring in Light Vehicles–System Performance. Technical Report of NHTSA (National Highway Traffic Safety Administration), U.S. Department of Transportation).
ISO (2008). Intelligent Transport Systems–Lane Change Decision Aid Systems Performance Requirements and Test Procedure. ISO-17387.
Jeong, S., Lee, J., Choi, S., Oh, J. and Lee, K. (2012). Technology analysis and low-cost design of automotive radar for adaptive cruise control system. Int. J. Automotive Technology 13, 7, 1133–1140.
Lee, M. and Kim, Y. (2010). Design and performance of a 24-GHz switch-antenna array FMCW radar system for automotive applications. IEEE Trans. Vehicular Technology 59, 5, 2290–2297.
Lin, B., Chan, Y., Fu, L., Hsiao, P., Chuang, L., Huang, S. and Lo, M. (2012). Integrating appearance and edge features for sedan vehicle detection in the blind-spot area. IEEE Trans. Intelligent Transportation Systems 13, 2, 737–747.
O'Malley, R., Glavin, M. and Jones, E. (2010). Visionbased detection and tracking of vehicles to the rear with perspective correction in low-light conditions. IET Intelligent Transport Systems 5, 1, 1–10.
Richards, M. (2005). Fundamentals of Radar Signal Processing. McGraw-Hill. New York, USA.
Shunji, M. (2004). New algorithm for multiple object detection in FM-CW radar. SAE Paper No. 2004-01-0177.
Texas Instruments (2012). C28x Floating Point Unit DSP Library. User’s Guide. FPU-DSP-LIB-UG-V131.
Winkler, V. (2007). Range Doppler detection for automotive FMCW radar. Proc. IEEE European Radar Conf., 166–169.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Hyun, E., Jin, Y.S. & Lee, J.H. Design and development of automotive blind spot detection radar system based on ROI pre-processing scheme. Int.J Automot. Technol. 18, 165–177 (2017). https://doi.org/10.1007/s12239-017-0017-5
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12239-017-0017-5