Abstract
The punching problem of reinforced concrete flat slabs and flat foundations has two main aspects, related to load carrying capacity of these structures under shear forces. The first is obtaining the shear force value, and the second–finding the control area (failure zone dimensions). Generally, the punching shear force is taken, based on experimental data, and the control perimeter is assigned according to existing design codes. At the same time, the assigned control perimeter is different for flat slabs and flat foundations. The available experimental and finite element analysis data, used for assigning this area, has a wide scatter and differs by 40-50% from the values, given in modern design provisions. The present study is focused on the above-mentioned second aspect and deals with exact evaluation of the control perimeter under shear punching in flat slabs and flat foundations. This study emphasizes the difference between punching shear due to concentrated load and support reaction force to distributed one. These both cases are investigated using mini-max principle: the internal shear forces are maximized and the control perimeter dimension leads to minimal external load. Efficiency of the proposed method is demonstrated by numerical examples and comparison with available data, based on results of experiments and finite element analyzes. The obtained results can be used as a basis for refinement of existing punching shear models and further development of modern design provisions in this field.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Ahmad, S. I. and Tanabe, T. (2013). “Three-dimensional FE analysis of reinforced concrete structures using the lattice equivalent continuum method.” Structural Concrete Journal of the fib, Vol. 1, No. 14, pp. 51–59.
Bazant, Z. P. and Zao, O. (1987). “Size effect in punching shear failure of slabs.” ACI Structural Journal, Vol. 84, No. 1, pp. 44–53.
Belletti, B., Damoni, C., Cervenka, V., and Hendriks, M. A. N. (2016). “Catenary action effects on the structural robustness assessment of RC slab strips subjected to shear and tensile forces.” Structural Concrete, Vol. 17, No. 6, pp. 1003–1016.
Belletti, B., Walraven, J. C., and Trapani, F. (2015). “Evaluation of compressive membrane action effects on punching shear resistance of reinforced concrete slabs.” Engineering Structures, Vol. 95, No. 7, pp. 25–39.
BR 52-101-2003 (2004). Non-pre-stressed concrete and reinforced concrete structures, NIIZhB, Moscow.
Brown, S. and Dilger, W. (2004). Design of slab- column connections to resist seismic loading, 13 th World Conference on Earthquake Engineering, Vancouver, Canada, August 1-6, Paper No. 2832.
Cantone, R., Belletti, B., Manelli, L., and Muttoni, A. (2016). “Compressive membrane action effects on punching strength of flat RC slabs.” Key Engineering Materials, Vol. 711, pp. 698–705, 8th International Conference on Concrete under Severe Conditions- Environment and Loading, Lecco, Italy, 12-14 September.
CEB: CEB-FIP Model Code 1990–Final draft, Bulletin Nos. 203/204/205. Comite Euro-international du Beton, Lausanne, 1991.
Eurocode 2: Design of Concrete Structures–Part 1-1: General Rules and Rules for Buildings, 2004.
Federation Internationale du Beton (fib): Model Code 2010, final draft, vol. 1. fib, Bulletin 65, Lausanne, Switzerland, Vol. 2, 350 pp. 2012.
Fernandez, Ruiz M. and Muttoni, A. (2009). “Applications of critical shear crack theory to punching of reinforced concrete slabs with transverse reinforcement.” ACI Structural Journal, Vol. 106, No. 4, pp. 485–494.
Hegger, J. and Beutel, R. (1998). Durchstanzen schubbewehrter Flachdecken im Bereich von Innenstutzen, Final report, AiF research project 10644N, Chair and Institute of Concrete Structures, RWTH Aachen University (in German).
IS 466 Concrete Code: General Principles, Part 1, The Standards Institution of Israel, 2003.
Iskhakov, I. (2001). “Quasi-isotropic ideally elastic-plastic model for calculation of RC elements without empirical coefficients.” Structural Engineering, Mechanics and Computation, volume I, Ed. A. Zingoni, Elsevier, pp. 367–374.
Iskhakov, I., Ribakov, Y., and Shah, A. (2009). “Experimental and theoretical investigation of column–flat slab joint ductility.” Materials and Design, Vol. 30, No. 8, pp. 3158–3164.
Iskhakov, I. and Ribakov, Y. (2013). “A new concept for design of fibered high strength RC elements using ULS method.” Materials and Design, Vol. 51, pp. 612–619.
Iskhakov, I. and Ribakov, Y. (2014a). Ultimate equilibrium of RC structures using mini-max principle, Nova Publishers.
Iskhakov, I. and Ribakov, Y. (2014b). “Exact solution of shear problem for inclined cracked bending reinforced concrete elements.” Materials and Design, Vol. 57, pp. 472–478.
Iskhakov, I. and Ribakov, Y. (2015). “Ultimate limit state of pre-stressed reinforced concrete elements.” Materials and Design, Vol. 75, pp. 9–16.
Karlin, S. (1959). Mathematical Methods and Theory in Games, Programming and Economics, Pergamon Press, London/Paris.
Kinnunen, S. and Nylander, H. (1960). Punching of concrete slabs without shear reinforcement, Transaction, 158, KTH, Stockholm.
Micallef, K., Sagaseta, J., Fernández, Ruiz M., and Muttoni, A. (2014). “Assessing punching shear failure in reinforced concrete flat slabs subjected to localized impact loading.” International Journal of Impact Engineering, Vol. 71, pp. 17–33.
Moraes, Neto B., Barros, J., and Melo, G. (2013). “A model for the prediction of the punching resistance of steel fibre reinforced concrete slabs centrically loaded.” Construction and Building Materials, Vol. 46, pp. 211–223.
Muttoni, A., Fernandez, Ruiz M., Bentz, E., Foster, S., and Sigrist, V. (2013). “Background to fib Model Code 2010 shear provisions–part II: Punching shear.” Structural Concrete Journal of the fib, Vol. 3, No. 14, pp. 204–214.
Reiss, M. (1994). Reinforced Concrete Slabs, Michlol (in Hebrew).
Vacev, T., Bonić, Z., Prolović, V., Davidović, N., and Lukić, D. (2015). “Testing and finite element analysis of reinforced concrete column footings failing by punching shear.” Engineering Structures, Vol. 92, No. 1, pp. 1–14.
Yankelevsky, D. Z. and Leibowitz, O. (1999). “Punching shear in concrete slabs.” International Journal of Mechanical Sciences, Vol. 41, No. 1, pp. 1–15.
Yitzhaki, D. (1966). “Punching strength of reinforced concrete slabs.” ACI Journal, Vol. 63, No. 5, pp. 527–542.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Iskhakov, I., Ribakov, Y. Calculation of RC Flat Slabs and Flat Foundations Punching Using Mini-Max Principle. KSCE J Civ Eng 22, 1872–1881 (2018). https://doi.org/10.1007/s12205-017-1763-7
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12205-017-1763-7