Abstract
To investigate the dynamic recrystallization behavior of 7xxx aluminum alloys, the isothermal compression tests were carried on the 7056 aluminum alloy in the temperatures range of 320–440 °C and in the strain rates range of 0.001–1 s−1. In addition, the microstructure of samples were observed via electron back scanning diffraction microscope. According to the results, true stress and true strain curves were established and an Arrhenius-type equation was established, showing the flow stress increases with the temperature decreasing and the strain rate increasing. The critical strain (εc) and the critical stress (σc) of the onset of dynamic recrystallization were identified via the strain hardening rate and constructed relationship between deformation parameters as follows: εc=6.71×10−4Z0.137 3 and σp=1.202σc+12.691. The DRX is incomplete in this alloy, whose volume fraction is only 20% even if the strain reaches 0.9. Through this study, the flow stress behavior and DRX behavior of 7056 aluminum alloys are deeply understood, which gives benefit to control the hot working process.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Dursun T, Soutis C. Recent Developments in Advanced aircraft Aluminium Alloys[J]. Mater. Des., 2014, 56: 862–871
Heinz A, Haszler A, Keidel C, et al. Recent Development in Aluminium Alloys for Aerospace Applications[J]. Mater. Sci. Eng. A, 2000, 280(1): 102–107
Ambrogio G, Filice L, Gagliardi F. Formability of Lightweight Alloys by Hot Incremental Sheet Forming[J]. Mater. Des., 2012, 34: 501–508
Liu X G, Han S, Chen L, et al. Flow Behavior and Microstructural Evolution of 7A85 High-strength Aluminum Alloy during Hot Deformation[J]. Metall. Mater. Trans. A, 2017, 48(5): 2 336–2 348
Shaha S K, Czerwinski F, Kasprzak W, et al. Interaction between Nano-precipitates and Dislocations during High Temperature Deformation of Al-Si Alloys[J]. J. Alloy. Compd., 2017(712): 219–224
Shi C J, Lai J, Chen X G. Microstructural Evolution and Dynamic Softening Mechanisms of Al-Zn-Mg-Cu Alloy during Hot Compressive Deformation[J]. Materials, 2014, 7(1): 244–264
Mc Queen H J. Hot Deformation and Processing of Aluminum Alloys [M]. Boca Raton: CRC Press, 2011
Quey R, Driver J H. Microtexture Tracking of Sub-Boundary Evolution During Hot Deformation of Aluminium[J]. Mater. Charact., 2011, 62(12): 1 222–1 227
Son K T, Kim M H, Kim S W, et al. Evaluation of Hot Deformation Characteristics in Modified AA5052 using Processing Map and Activation Energy Map under Deformation Heating[J]. J. Alloy. Compd., 2018, 740: 96–108
Sun Y, Cao Z H, Wan Z P, et al. 3D Processing Map and Hot Deformation Behavior of 6A02 Aluminum Alloy[J]. J. Alloy. Compd., 2018, 742: 356–368
Huang X, Zhang H, Han Y, et al. Hot Deformation Behavior of 2026 Aluminum Alloy during Compression at Elevated Temperature[J]. Mater. Sci. Eng. A, 2010, 527(3): 485–490
Li J, Shen J, Yan X, et al. Microstructure Evolution of 7050 Aluminum Alloy during Hot Deformation[J]. T. Nonferr. Metal. Soc., 2010, 20(2): 189–194
Liu J, Cui Z S, Ruan L Q. A New Kinetics Model of Dynamic Recrystallization for Magnesium Alloy AZ31B[J]. Mater. Sci. Eng. A, 2011, 529: 300–310
Quan G, Mao Y, Li G, et al. A Characterization for the Dynamic Recrystallization Kinetics of As-extruded 7075 Aluminum Alloy Based on True Stress—strain Curves[J]. Comp. Mater. Sci., 2012, 55: 65–72
Quan G Z, Li G S, Chen T, et al. Dynamic Recrystallization Kinetics of 42CrMo Steel during Compression at Different Temperatures and Strain Rates[J]. Mater. Sci. Eng. A, 2011, 528(13–14): 4 643–4 651
Wang M H, Li Y F, Wang W, et al. Quantitative Analysis of Work Hardening and Dynamic Softening Behavior of Low Carbon Alloy Steel Based on the Flow Stress[J]. Mater. Des., 2013(45): 384–392
Chen X, C L Y, Wen D, et al. Dynamic Recrystallization Behavior of A Typical Nickel-based Superalloy during Hot Deformation[J]. Mater. Des., 2014, 57(5): 568–577
Shi C J, Chen X G. Evolution of Activation Energies for Hot Deformation of 7150 Aluminum Alloys with Various Zr and V Additions[J]. Mater. Sci. Eng. A, 2016, 650: 197–209
Huang C Q, Deng J, Wang S X, et al. A Physical-based Constitutive Model to Describe the Strain-hardening and Dynamic Recovery Behaviors of 5754 Aluminum Alloy[J]. Mater. Sci. Eng. A, 2017, 699: 106–113
Lin Y C, Xia Y, Chen X, et al. Constitutive Descriptions for Hot Compressed 2124-t851 Aluminum Alloy over A Wide Range of Temperature and Strain Rate[J]. Comp. Mater. Sci., 2010, 50(1): 227–233
Wang Y J, Peng J, Zhong L P, et al. Modeling and Application of Constitutive Model Considering the Compensation of Strain during Hot Deformation[J]. J. Alloy. Compd., 2016, 681: 455–470
Mirzadeh H, Najafizadeh A. Prediction of the Critical Conditions for Initiation of Dynamic Recrystallization[J]. Mater. Des., 2010, 31(3): 1 174–1 179
Jonas J J, Poliak E I. The Critical Strain for Dynamic Recrystallization in Rolling Mills[J]. Materials Science Forum, 2003, 426: 57–66
Rokni M R, Zarei-Hanzaki A, Roostaei A A, et al. An Investigation into the Hot Deformation Characteristics of 7075 Aluminum Alloy[J]. Mater. Des., 2011, 32(4): 2 339–2 344
Sun Y L, Xie J P, Hao S M, et al. Dynamic Recrystallization Model of 30% SiCp/Al Composite[J]. J. Alloy Compd., 2015, 649: 865–871
Funding
Funded by the National Key R&D Program of China (Nos. 2016YFB0300803, 2016YFB0300903) and the National Program of China (No. 2012CB619504)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Shi, G., Zhang, Y., Li, X. et al. Dynamic Recrystallization Behavior of 7056 Aluminum Alloys during Hot Deformation. J. Wuhan Univ. Technol.-Mat. Sci. Edit. 37, 90–95 (2022). https://doi.org/10.1007/s11595-022-2503-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11595-022-2503-5