Abstract
Fly ash/A1-Mg composites are fabricated by powder metallurgical method. The morphology and structure of fly ash/A1-Mg composites are characterized by scanning electron microscope (SEM) and X-ray diffraction, respectively. The influences of different fly ash content on the friction and wear behavior of the composites are investigated at a constant sliding velocity of 400 r/min and the worn mechanism of composites is discussed. The results indicate that the friction coefficient is steadily lower than that of Al alloy matrix at the lower fly ash content and loads. For the fly ash/A1-Mg composites, the wear mechanism is characterized as abrasive wear and adhesive wear under small normal load and at low fly ash content, and it is characterized as delamination wear and abrasive wear transferred onto the counterpart under high normal load and at high fly ash content.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
N Saheb, T Laoui, A R Daud, et al. Influence of Ti Addition on Wear Properties of Al-So Eutectic Alloys[J]. Wear, 2001, 249: 656–662
N Saheb, T Laoui, A R Daud, et al. Microstructure and Hardness Behaviours of Ti-containing Al-Si Alloys[J]. Philosophical Magazine A, 2002, 82: 803–814
H L Lee, W H Lu, S L I Chan. Abrasive Wear of Powder Metallurgy 6061Al-SiC Particle Composites[J]. Wear, 1992,159: 223–231
S Jacobson, N Axen. Transitions in the Abrasive Wear Resistance of Fibre and Particle-reinforced Aluminium[J]. Wear, 1994,178: 1–7
C G Cordovilla, J Narciso, E Louis. Abrasive Wear Resistance of Aluminum Alloy/Ceramic Particulate Composites [J]. Wear, 1996, 192: 170–177
B Venkataraman, G Sundararajan. Correlation between the Characteristics of the Mechanically Mixed Layer and Wear Behaviour of Aluminium,Al-7075 Alloy and Al-MMCs[J]. Wear, 2000, 245:22–38
E Candan, H Ahlatci, H Cimenoglu. Abrasive Wear Behaviour of Al-SiC Composites Produced by Pressure Infiltration Technique[J]. Wear, 247:133–138
M Takagi, H Ohta, T Imura, et al. Wear Properties of Nanocrystalline Aluminum Alloys and Their Composites[J]. Wear, 2001, 44: 2 145–2 148
M L T Guo, C A Tsao. Tribological Behavior of Aluminum/SiC/Nickel-Coated Graphite Hybrid Composites[J]. Mater. Sci. Eng., 2002, 333: 134–145
L J Yang. The Transient and Steady Wear Coefficients of A6061 Aluminium Alloy Reinforced with Alumina Particles[J]. Compos. Sci. Technol., 2003, 63:575–583
A M Al-Qutub, I M Allam, T W Qureshi. Effect of Sub-micron Al2O3 Concentration on Dry Wear Properties of 6061 Aluminum Based Composite[J]. J. Mater. Process. Technol., 2006, 172: 327–331
Y Wang, W M Rainforth, H Jones, et al. Dry Wear Behaviour and Its Relation to Microstructure of Novel 6092 Aluminium Alloy-Ni3Al Powder Metallurgy Composite[J]. Wear, 2001, 251: 1 421–1 432
F Tang, X Wu, S Ge, et al. Dry Sliding Friction and Wear Properties of B4C Particulate-reinforced Al-5083 Matrix Composites[J]. Wear, 2008, 264: 555–561
Z H Melgarejo, O M Sua. Wear Resistance of a Functionally-graded Aluminum Matrix Composite[J]. Scripta Mater., 2006, 55: 95–98
P K Rohatgi, R Q Guo, H Iksan, et al. Pressure Infiltration Technique for Synthesis of Aluminum-fly Ash Particulate Composite[J]. Mater. Sci. Eng., 1998, 244:22–30
T P D Rajan, R M Pillai, B C Pai, et al. Fabrication and Characterisation of Al-7Si-0.35Mg/fly Ash Metal Matrix Composites Processed by Different Stir Casting Routes[J]. Compos. Sci. Technol., 2007, 67:3 369–3 377
G Laplanchea, A Joulaina, J Bonnevillea, et al. Microstructures and Mechanical Properties of Al-base Composite Materials Reinforced by Al-Cu-Fe Particles[J]. J. Alloys Compd., 2010, 493: 453–460
M K Surappa, P K Rohatgi. Preparation and Properties of Cast Aluminium-ceramic Particle Composites[J]. J. Mater. Sci., 1981,16: 983–993
Suraj Rawal. Metal-matrix Composites for Space Applications[J]. JOM, 2001,53(4):14–17
J H Qin, Z S Zhang, M Y He. Study on CBC Composites Made by Waste Foundry Sand and Fly Ash[J]. Foundry, 2005, 154(11): 1 138–1 141
L L Wu, G C Yao, Y H Liu. Melt Delamination and Control in Cenosphere Fly Ash Reinforced Composites Prepared by Stir Casting[J]. Acta Mater. Compos. Sinica, 2005, 22(3): 126–129
R Q Guo, P K Rohatgi. Chemical Reactions between Aluminum and Fly Ash During Synthesis and Reheating of Al-fly Ash Composite[J]. Metall. Mater. Trans. B, 1998, 29: 519–525
G Ranganath, S C Sharma, M Krishna. Dry Sliding Wear of Garnet Reinforced Zinc/Aluminium Metal Matrix Composites[J]. Wear, 2001, 250-251:1 408–1 413
S Wilson, A T Alpas. Wear Mechanism Maps for Metal Matrix Composites[J]. Wear, 1997, 212: 41–49
M Sudarshan, K Surappa. Dry Sliding Wear of Fly Ash Particle Reinforced A356 Al Composites[J]. Wear, 2008, 265: 349–360
R M Pillai, Ramani Geetha. Characterisation of Stir Cast Al-12Si-X flyash Composites[J]. Aluminum in India. 2006, 5:15–24
J Bienias, M Walczak, B Surowska, et al. Microstructure and Corrosion Behaviour of Aluminum Fly Ash Composites[J]. J. Optoelec. Adv. Mater., 2003, 5(2):493–502
G H Wu, Z Y Dou, L T Jiang, et al. Damping Properties of Aluminum Matrix-fly Ash Composites[J]. Mater. Lett., 2006, 60: 2 945–2 948
P K Rohatgi, J K Kim, N Gupta, et al. Compressive Characteristics of A356/Fly Ash Cenosphere Composites Synthesized by Pressure Infiltration Technique[J]. Compos. Part A, 2006, 37: 430–437
V M Kevorkijan. The Quality of Aluminum Dross Particles and Costeffective Reinforcement for Structural Aluminum-based Composites[J]. Compos. Sci. Technol., 1999, 59:1 745–1 751
R Q Guo, D Venugopalan, P K Rohatgi. Differential Thermal Analysis to Establish the Stability of Aluminum-fly Ash Composites during Synthesis and Reheating[J]. Mater. Sci. Eng. A, 1998,241:184–90
Author information
Authors and Affiliations
Corresponding author
Additional information
Funded by National Natural Science Foundation of China (No.51174006), Anhui Provincial Natural Science Foundation (No.1208085QE100), Educational Commission of Anhui Province of China (No. KJ2012ZD05)
Rights and permissions
About this article
Cite this article
Wang, Q., Min, F. & Zhu, J. Microstructural characterization and mechanical property of Fly Ash/Al-25Mg composites. J. Wuhan Univ. Technol.-Mat. Sci. Edit. 29, 1019–1022 (2014). https://doi.org/10.1007/s11595-014-1036-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11595-014-1036-y