Abstract
Strain and stress concentrations are studied for elastomers at finite deformations. Effects of strain-induced crystallization, filler reinforcement and deformation rate are also investigated, and micromechanical descriptions are provided for the observed results. A simple problem is subjected to finite element simulations to show the results evidently. Material parameters are obtained from experimental tests conducted on standard tensile samples of filled and unfilled natural rubber (NR) as well as styrene–butadiene rubber (SBR) as crystallizing and non-crystallizing rubbers, respectively. In all simulations, the strain concentration factor \(K_E\) is shown to decrease monotonically where the reduction is more apparent as the filler content increases. At enough large stretches, \(K_E\) is higher for filled NRs compared to the unfilled NR which is not the case for SBR. The stress concentration factor \(K_S\) rises sharply by deformation of the samples. At large stretches, in the case of SBR, filler reinforcement only shifts the maximum value of \(K_S\) to a lower level of strain, while in the case of NR, it reduces \(K_S\) significantly. It is concluded that \(K_S\) can rise from its theoretical value remarkably which should be noticed in design purposes particularly for crystallizing elastomers. Furthermore, the effect of deformation rate is investigated employing a visco-hyperelastic constitutive law along with an associated VUMAT in ABAQUS/Explicit. It is observed that, at high deformation rates, \(K_E\) decreases. Despite the reduction in strain concentration, \(K_S\) would be higher which is not desired in design of mechanical parts.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Mark, J.E., Erman, B., Eirich, F.R.: The Science and Technology of Rubber. Academic Press, New York (2005)
Ward, I.M., Sweeney, J.: An Introduction to the Mechanical Properties of Solid Polymers. Wiley, New York (2004)
Lindley, P.B.: Strain concentrations at the corners of stretched rubber sheets. J. Strain Anal. Eng. Des. 6, 279–285 (1971)
Kadlowec, J., Wineman, A., Hulbert, G.: Elastomer bushing response: experiments and finite element modeling. Acta Mech. 163, 25–38 (2003)
Walter, D.P., Pilkey, D.: Peterson’s Stress Concentration Factors, 3rd edn. Wiley, New York (2008)
Elmukashfi, E., Kroon, M.: Numerical analysis of dynamic crack propagation in biaxially strained rubber sheets. Eng. Fract. Mech. 124–125, 1–17 (2014)
Yang, Z., Kim, C.-B., Cho, C., Beom, H.G.: The concentration of stress and strain in finite thickness elastic plate containing a circular hole. Int. J. Solids Struct. 45, 713–731 (2008)
Yang, Z.: Stress and strain concentration factors for tension bars of circular cross-section with semicircular groove. Eng. Fract. Mech. 76, 1683–1690 (2009)
Fukahori, Y., Seki, W.: Stress analysis of elastomeric materials at large extensions using the finite element method. J. Mater. Sci. 28, 4471–4482 (1993)
Troyani, N., Gomes, C., Sterlacci, G.: Theoretical stress concentration factors for short rectangular plates with centered circular holes. J. Mech. Des. 124, 126–128 (2002)
Troyani, N., Sterlacci, G., Gomes, C.: Simultaneous considerations of length and boundary conditions on theoretical stress concentration factors. Int. J. Fatigue 25, 353–355 (2003)
Timoshenko, S., Goodier, J.N.: Theory of Elasticity. McGraw-Hill Book Company, New York (1970)
Darijani, H., Naghdabadi, R.: Hyperelastic materials behavior modeling using consistent strain energy density functions. Acta Mech. 213, 235–254 (2010)
Arruda, E.M., Boyce, M.C.: A three-dimensional constitutive model for the large stretch behavior of rubber elastic materials. J. Mech. Phys. Solids 41, 389–412 (1993)
Pucci, E., Saccomandi, G.: A note on the Gent model for rubber-like materials. Rubber Chem. Technol. 75, 839–851 (2002)
Khajehsaeid, H., Arghavani, J., Naghdabadi, R.: A hyperelastic constitutive model for rubber-like materials. Eur. J. Mech. A Solids 38, 144–151 (2013)
Khajehsaeid, H., Naghdabadi, R., Arghavani, J.: A strain energy function for rubber-like materials. Const. Models Rubber 8, 205–210 (2013)
Khajehsaeid, H., Rabiei, S.: Effect of intermolecular forces in mechanical behavior of elastomers. In: Proceedings of the Society of Engineering Science 51st Annual Technical Meeting, West Lafayette, Purdue University October 1–3, 2014. Purdue University Libraries Scholarly Publishing Services
Rivlin, R.S., Saunders, D.W.: Large elastic deformations of isotropic materials. VII. Experiments on the deformation of rubber. Philos. Trans. R. Soc. Lond. Ser. A Math. Phys. Sci. 243, 251–288 (1951)
Ogden, R., Saccomandi, G., Sgura, I.: Fitting hyperelastic models to experimental data. Comput. Mech. 34, 484–502 (2004)
Pal, K., Rajasekar, R., Kang, D.J., Zhang, Z.X., Pal, S.K., Das, C.K., Kim, J.K.: Effect of fillers on natural rubber/high styrene rubber blends with nano silica: morphology and wear. Mater. Des. 31, 677–686 (2010)
Dannenberg, E.: The effects of surface chemical interactions on the properties of filler-reinforced rubbers. Rubber Chem. Technol. 48, 410–444 (1975)
Berriot, J., Lequeux, F., Monnerie, L., Montes, H., Long, D., Sotta, P.: Filler-elastomer interaction in model filled rubbers, a 1H NMR study. J. Non Cryst. Solids 307, 719–724 (2002)
Leblanc, J.L.: Rubber-filler interactions and rheological properties in filled compounds. Prog. Polym. Sci. 27, 627–687 (2002)
Tangudom, P., Thongsang, S., Sombatsompop, N.: Cure and mechanical properties and abrasive wear behavior of natural rubber, styrene-butadiene rubber and their blends reinforced with silica hybrid fillers. Mater. Des. 53, 856–864 (2014)
Fritzsche, J., Klüppel, M.: Structural dynamics and interfacial properties of filler-reinforced elastomers. J. Phys. Condens. Matter 23, 1–11 (2011)
Horgan, C.O., Ogden, R.W., Saccomandi, G.: A theory of stress softening of elastomers based on finite chain extensibility. Proc. R. Soc. Lond. Ser. A Math. Phys. Eng. Sci. 460, 1737–1754 (2004)
Marckmann, G., Verron, E., Gornet, L., Chagnon, G., Charrier, P., Fort, P.: A theory of network alteration for the Mullins effect. J. Mech. Phys. Solids 50, 2011–2028 (2002)
Bueche, F.: Molecular basis for the Mullins effect. J. Appl. Polym. Sci. 4, 107–114 (1960)
Diani, J., Fayolle, B., Gilormini, P.: A review on the Mullins effect. Eur. Polym. J. 45, 601–612 (2009)
Khajehsaeid, H.: Development of a network alteration theory for the Mullins-softening of filled elastomers based on the morphology of filler-chain interactions. Int. J. Solids Struct. 80, 158–167 (2016)
Negahban, M.: Modeling the thermomechanical effects of crystallization in natural rubber: I. The theoretical structure. Int. J. Solids Struct. 37, 2777–2789 (2000)
Fukahori, Y.: The mechanics and mechanism of the carbon black reinforcement of elastomers. Rubber Chem. Technol. 76, 548–566 (2003)
Hoo Fatt, M.S., Ouyang, X.: Integral-based constitutive equation for rubber at high strain rates. Int. J. Solids Struct. 44, 6491–6506 (2007)
Amin, A.F.M.S., Lion, A., Sekita, S., Okui, Y.: Nonlinear dependence of viscosity in modeling the rate-dependent response of natural and high damping rubbers in compression and shear: Experimental identification and numerical verification. Int. J. Plast. 22, 1610–1657 (2006)
Bergström, J., Boyce, M.: Constitutive modeling of the time-dependent and cyclic loading of elastomers and application to soft biological tissues. Mech. Mater. 33, 523–530 (2001)
Reese, S.: A micromechanically motivated material model for the thermo-viscoelastic material behaviour of rubber-like polymers. Int. J. Plast. 19, 909–940 (2003)
Anani, Y., Alizadeh, Y.: Visco-hyperelastic constitutive law for modeling of foam’s behavior. Mater. Des. 32, 2940–2948 (2011)
Hoo Fatt, M.S., Ouyang, X.: Three-dimensional constitutive equations for Styrene Butadiene rubber at high strain rates. Mech. Mater. 40, 1–16 (2008)
Khajehsaeid, H., Arghavani, J., Naghdabadi, R., Sohrabpour, S.: A visco-hyperelastic constitutive model for rubber-like materials: a rate-dependent relaxation time scheme. Int. J. Eng. Sci. 79, 44–58 (2014)
Khajehsaeid, H., Baghani, M., Naghdabadi, R.: Finite strain numerical analysis of elastomeric bushings under multi-axial loadings: a compressible visco-hyperelastic approach. Int. J. Mech. Mater. Des. 9, 385–399 (2013)
Khajehsaeid, H., Ramezani, M.A.: Visco-hyperelastic modeling of automotive elastomeric bushings with emphasis on the coupling effect of axial and torsional deformations. In: Proceedings of the Society of Engineering Science 51st Annual Technical Meeting, West Lafayette, Purdue University October 1–3, 2014. Purdue University Libraries Scholarly Publishing Services
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Khajehsaeid, H., Reese, S., Arghavani, J. et al. Strain and stress concentrations in elastomers at finite deformations: effects of strain-induced crystallization, filler reinforcement, and deformation rate. Acta Mech 227, 1969–1982 (2016). https://doi.org/10.1007/s00707-016-1615-4
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00707-016-1615-4