Abstract
In order to solve the problems of high cost and low efficiency in milling of titanium alloy, multiobjective optimizations are proposed to optimize machining and ultrasonic parameters by nondominated sorting genetic algorithm II (NSGA-II). In the present work, longitudinal-torsion ultrasonic vibration has been superimposed to the milling of titanium alloy (Ti-6Al-4V). Orthogonal experiment of milling has been carried out to evaluate influence of the parameters on machining results. Then, to meet the different engineering demands, three multiobjective optimization models are established to obtain optimization parameters. According to the optimization results, a group of milling verified experiments was developed for optimized models. The results show that the three optimization models balance the different objective well, and the optimization results are close to experiment results. It provides choices for engineering application.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Oh JM, Heo KH, Kim WB, Choi GS, Lim JW (2013) Sintering properties of Ti-6Al-4V alloys prepared using Ti/TiH2 powders. Mater Trans 54:119–121. doi:10.2320/matertrans.M2012304
Ellyson B, Brochu M, Brochu M (2017) Characterization of bending vibration fatigue of SLM fabricated Ti-6Al-4V. Int J Fatigue 99:25–34. doi:10.1016/j.ijfatigue.2017.02.005
Mohsan AUH, Liu Z, Padhy GK (2017) A review on the progress towards improvement in surface integrity of Inconel 718 under high pressure and flood cooling conditions. Int J Adv Manuf Technol 91:107–125. doi:10.1007/s00170-016-9737-3
Shokrani A, Dhokia V, Newman ST (2016) Investigation of the effects of cryogenic machining on surface integrity in CNC end milling of Ti-6Al-4V titanium alloy. J Manuf Process 21:172–179. doi:10.1016/j.jmapro.2015.12.002
Jackson MJ, Novakov T, Da Silva MB, Machado AR (2017) Predicting chip and non-chip formation when micromachining Ti-6Al-4V titanium alloy. Int J Adv Manuf Technol 91:955–985. doi:10.1007/s00170-016-9754-2
Grigoriev SN, Vereschaka AA, Fyodorov SV, Sitnikov NN, Batako AD (2017) Comparative analysis of cutting properties and nature of wear of carbide cutting tools with multi-layered nano-structured and gradient coatings produced by using of various deposition methods. Int J Adv Manuf Technol 90:3421–3435. doi:10.1007/s00170-016-9676-z
Jiao F, Niu Y, Liu X (2015) Effect of ultrasonic vibration on surface white layer in ultrasonic aided turning of hardened GCr15 bearing steel. Mater Res Innov 19:938–942. doi:10.1179/1432891715Z.0000000001844
Tao G, Ma C, Shen X, Zhang J (2017) Experimental and modeling study on cutting forces of feed direction ultrasonic vibration-assisted milling. Int J Adv Manuf Technol 90:709–715. doi:10.1007/s00170-016-9421-7
Ko JH, Ehmann KF (2013) Investigation of the effect of tooling axial ultrasonic vibration assistance on meso-scale milled surfaces, Berlin, Germany, [C]. euspen, 2013
Ahmed Y, Cong WL, Stanco MR, Xu ZG, Pei ZJ, Treadwell C, Zhu YL, et al. (2012) Rotary ultrasonic machining of alumina dental ceramics: a preliminary experimental study on surface and subsurface damages. J Manuf Sci Eng, Trans ASME, 134 doi: 10.1115/1.4007711
Hara K, Isobe H, Ismail MF (2012) Ultrasonically assisted machining for mirror finishing of die (3rd report)—a research of effects of cutting edge truncation on grinding phenomenon. Seimitsu Kogaku Kaishi/Journal of the Japan Society for Precision Engineering 78:641–645
Wang M, Li S, Zheng Y (2014) Surface roughness of titanium alloy under ultrasonic vibration milling. Nongye Jixie Xuebao/Trans Chin Soc Agric Mach 45:341–346. doi:10.6041/j.issn.1000-1298.2014.06.052
Jiang X, Liang H, Lu H, Dai J, Zhang D (2014) Investigation of ultrasonic elliptical vibration milling of thin-walled titanium alloy parts. Binggong Xuebao/Acta Armamentarii 35:1891–1897. doi:10.3969/j.issn.1000-1093.2014.11.022
Soutome T, Sato K (2013) Study on ultrasonic vibration cutting (2nd report)—analysis and consideration of cylindrical profile and surface roughness by vibration cutting on thrust force direction. Seimitsu Kogaku Kaishi/J Jpn Soc Precis Eng 79:766–772
Budak E, Altintas Y (1992) Flexible milling force model for improved surface error predictions, Istanbul, Turk, 1992[C]. Publ by ASME
Merdol SD, Altintas Y (2008) Virtual simulation and optimization of milling operations—part I: process simulation. J Manuf Sci Eng Trans ASME 130:510041–5100412. doi:10.1115/1.2927434
Liu C, Tang D, He H, Chen X (2013) Prediction of surface roughness for end milling titanium alloy using modified particle swarm optimization LS-SVM. Trans Nanjing Univ Aeronaut Astronaut 30:53–61
Mahdavinejad RA, Khani N, Fakhrabadi MMS (2012) Optimization of milling parameters using artificial neural network and artificial immune system. J Mech Sci Technol 26:4097–4104. doi:10.1007/s12206-012-0882-9
Brecher C, Fey M, Tenbrock C, Daniels M. (2016) Multipoint constraints for modeling of machine tool dynamics. J Manuf Sci Eng Trans ASME,138. doi: 10.1115/1.4031771
Li J, Yang X, Ren C, Chen G, Wang Y (2014) Multiobjective optimization of cutting parameters in Ti-6Al-4V milling process using nondominated sorting genetic algorithm-II. Int J Adv Manuf Technol 76:941–953. doi:10.1007/s00170-014-6311-8
Chakraborti N, Siva Kumar B, Satish Babu V, Moitra S, Mukhopadhyay A (2006) Optimizing surface profiles during hot rolling: a genetic algorithms based multi-objective optimization. Comput Mater Sci 37:159–165. doi:10.1016/j.commatsci.2005.12.031
Koura OM, El-Akkad AS (2016) Optimization of cutting conditions using regression and genetic algorithm in end milling. Int J Eng Res Afr 20:12–18. doi:10.4028/www.scientific.net/JERA.20.12
Gholami MH, Azizi MR (2014) Constrained grinding optimization for time, cost, and surface roughness using NSGA-II. Int J Adv Manuf Technol 73:981–988. doi:10.1007/s00170-014-5884-6
Emmanuel Nicholas P, Lenin Babu MC, Sathya SA (2016) Multiobjective optimization of laminated composite plate with elliptical cut-out using ANN based NSGA-II. J Mech Mater Struct 11:157–172. doi:10.2140/jomms.2016.11.157
Deb K, Datta R (2012) Hybrid evolutionary multi-objective optimization and analysis of machining operations. Eng Optim 44:685–706. doi:10.1080/0305215X.2011.604316
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Niu, Y., Jiao, F., Zhao, B. et al. Multiobjective optimization of processing parameters in longitudinal-torsion ultrasonic assisted milling of Ti-6Al-4V. Int J Adv Manuf Technol 93, 4345–4356 (2017). https://doi.org/10.1007/s00170-017-0871-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0871-3