Abstract
Laser-MIG hybrid welding of 316L stainless steel was carried out to investigate influence of welding process parameters, i.e., laser power (P), welding current (I), distance between laser and arc (D), and welding speed (V) on arc characteristics, droplet transfer, and weld quality. Arc characteristics and droplet transfer behavior were investigated using high-speed imaging technology. Microstructures of the joint were observed by optical microscope, and microhardness was measured by microhardness tester. The results showed that the maximum deviation angle of the arc from the wire axis decreases with the increasing laser power. Welding current played a dominant role in arc length and droplet transfer mode. Optimal weld with no spatters and humps was obtained when P = 3 kW, I = 140 A, D = 3 mm, and V = 1.2 m/min. Microstructures in the weld zone mainly consist of columnar and equiaxed dendrites. Microhardness decreased toward the center of the weld zone, increased toward the WZ boundary, and decreased sharply at the heat-affected zone (HAZ).
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Traverso P, Canepa E (2014) A review of studies on corrosion of metals and alloys in deep-sea environment. Ocean Eng 87:10–15. doi:10.1016/j.oceaneng.2014.05.003
Wang ZY, Cong Y, Zhang T (2014) Effect of hydrostatic pressure on the pitting corrosion behavior of 316L stainless steel. Int J Electrochem Sci 9:778–798
Elmesalamy A, Francis JA, Li L (2014) A comparison of residual stresses in multi pass narrow gap laser welds and gas-tungsten arc welds in AISI 316L stainless steel. Int J Pres Vessel Pip 113:49–59. doi:10.1016/j.ijpvp.2013.11.002
Buddu RK, Chauhan N, Raole PM (2014) Mechanical properties and microstructural investigations of TIG welded 40mm and 60mm thick SS 316L samples for fusion reactor vacuum vessel applications. Fusion Eng Des 89(12):3149–3158. doi:10.1016/j.fusengdes.2014.10.006
Duan ZL, Qin RY, He G (2014) Mass transfer and weld appearance of 316L stainless steel covered electrode during shielded metal arc welding. Metall Mater Trans A 45(2):843–853. doi:10.1007/s11661-013-2001-7
Chukkan JR, Vasudevan M, Muthukumaran S, Kumar RR, Chandrasekhar N (2015) Simulation of laser butt welding of AISI 316L stainless steel sheet using various heat sources and experimental validation. J Mater Process Technol 219:48–59. doi:10.1016/j.jmatprotec.2014.12.008
Tomashchuk I, Grevey D, Sallamand P (2015) Dissimilar laser welding of AISI 316L stainless steel to Ti6-Al4-6V alloy via pure vanadium interlayer. Mater Sci Eng A 622:37–45. doi:10.1016/j.msea.2014.10.084
Köse C, Kaçar R, Zorba AP, Bağırova M, Allahverdiyev AM (2016) The effect of CO2 laser beam welded AISI 316L austenitic stainless steel on the viability of fibroblast cells, in vitro. Mater Sci Eng C 60:211–218. doi:10.1016/j.msec.2015.11.035
Ribic B, Palmer TA, DebRoy T (2009) Problems and issues in laser-arc hybrid welding. Int Mater Rev 54(4):223–244. doi:10.1179/174328009X411163
Cao X, Wanjara P, Huang J, Munro C, Nolting A (2011) Hybrid fiber laser-arc welding of thick section high strength low alloy steel. Mater Des 32(6):3399–3413. doi:10.1016/j.matdes.2011.02.002
Casalino G, Campanelli SL, Ludovico AD (2013) Laser-arc hybrid welding of wrought to selective laser molten stainless steel (2014). Int J Adv Manuf Technol 68(1–4):209–216. doi:10.1007/s00170-012-4721-z
Liu W, Ma J, Yang G, Kovacevic R (2014) Hybrid laser-arc welding of advanced high-strength steel. J Mater Process Technol 214(12):2823–2833. doi:10.1016/j.jmatprotec.2014.06.018
Liu LM, Yuan ST, Li CB (2012) Effect of relative location of laser beam and TIG arc in different hybrid welding modes. Sci Technol Weld Join 17:441–446. doi:10.1179/1362171812Y.0000000033
Foster M, Beaulieu R, Blais L, Caron G, Langlois M (2013) Experimental investigation on stainless steel welding with a 15 kW fibre laser. Can J Phys 92:246–252. doi:10.1139/cjp-2012-0558
Chen Y, Feng J, Li L, Li Y, Chang S (2013) Effects of welding positions on droplet transfer in CO2 laser-MAG hybrid welding. Int J Adv Manuf Technol 68(5–8):1351–1359. doi:10.1007/s00170-013-4926-9
Zhang W, Hua XM, Liao W, Li F, Wang M (2014) Study of metal transfer in CO2 laser + GMAW-P hybrid welding using argon-helium mixtures. Opt Laser Technol 56:158–166. doi:10.1016/j.optlastec.2013.08.006
Zhang W, Hua XM, Liao W, Li F, Wang M (2014) Behavior of the plasma characteristic and droplet transfer in CO2 laser-GMAW-P hybrid welding. Int J Adv Manuf Technol 72:935–942. doi:10.1007/s00170-014-5731-9
Liu SY, Liu FD, Xu CY, Zhang H (2013) Experimental investigation on arc characteristic and droplet transfer in CO2 laser-metal arc gas (MAG) hybrid welding. Int J Heat Mass Transf 62:604–611. doi:10.1016/j.ijheatmasstransfer.2013.03.051
Ghosal S, Chaki S (2010) Estimation and optimization of depth of penetration in hybrid CO2 laser-MIG welding using ANN-optimization hybrid model. Int J Adv Manuf Technol 47(9):1149–1157. doi:10.1007/s00170-009-2234-1
Moradi M, Ghoreishi M, Frostevarg J, Kaplan AFH (2013) An investigation on stability of laser hybrid arc welding. Opt Lasers Eng 51:481–487. doi:10.1016/j.optlaseng.2012.10.016
Wahba M, Mizutani M, Katayama S (2015) Hybrid welding with fiber laser and CO2 gas shielded arc. J Mater Process Technol 221:146–153. doi:10.1016/j.jmatprotec.2015.02.004
Liu SY, Liu FD, Zhang H, Shi Y (2012) Analysis of droplet transfer mode and forming process of weld bead in CO2 laser-MAG hybrid welding process. Opt Laser Technol 44:1019–1025. doi:10.1016/j.optlastec.2011.10.016
Sathiya P, Mishra MK, Shanmugarajan B (2012) Effect of shielding gases on microstructure and mechanical properties of super austenitic stainless steel by hybrid welding. Mater Des 33:203–212. doi:10.1016/j.matdes.2011.06.065
Cui CY, Cui XG, Ren XD, Liu TT, Hu JD, Wang YM (2013) Microstructure and microhardness of fiber laser butt welded joint of stainless steel plates. Mater Des 49:761–765. doi:10.1016/j.matdes.2013.02.059
Zhang L, Lu JZ, Luo KY, Feng AX, Dai FZ, Zhong JS, Luo M, Zhang YK (2013) Residual stress, micro-hardness and tensile properties of ANSI 304 stainless steel thick sheet by fiber laser welding. Mater Sci Eng A 561:136–144. doi:10.1016/j.msea.2012.11.001
Thomy C, Vollertsen F (2012) Laser-MIG hybrid welding of aluminium to steel—effect of process parameters on joint properties. Weld World 56:124–132
Serizawa H, Mori D, Shirai Y, Ogiwara H, Mori H (2013) Weldability of dissimilar joint between F82H and SUS316L under fiber laser welding. Fusion Eng Des 88:2466–2470. doi:10.1016/j.fusengdes.2013.03.041
Serizawa H, Mori D, Ogiwara H, Mori H (2014) Effect of laser beam position on mechanical properties of F82H/SUS316L butt-joint welded by fiber laser. Fusion Eng Des 89:1764–1768. doi:10.1016/j.fusengdes.2013.12.003
Kim YS, Eagar TW (1993) Numerical analysis of metal transfer in gas metal arc welding. Weld J 72(6):269–277
Yilbas BS, Akhtar S (2013) Laser welding of AISI 316 steel: microstructural and stress analysis. J Manuf Sci Eng 135(3):031018. doi:10.1115/1.4024155
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Gao, Z., Jiang, P., Wang, C. et al. Study on droplet transfer and weld quality in laser-MIG hybrid welding of 316L stainless steel. Int J Adv Manuf Technol 88, 483–493 (2017). https://doi.org/10.1007/s00170-016-8774-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-8774-2