Abstract
Friction stir welding (FSW), as a solid state joining technique, has emerged as an efficient method for manufacturing tailor-welded blanks to optimize weight or performance in the final component. As the basic design of lightweight frame structures in the automotive and aircraft industry is frequently based on tubular profiles, the joining strategies and forming technologies have to be developed accordingly. In the present study, FSW tube was produced by a novel processing sequence. The plastic deformation characteristics during hydroforming were experimentally and numerically investigated with two types of end condition. The hydroforming performance of the FSW tubes was mainly investigated by die-bulge forming with fixed ends, and the wrinkling behavior during hydroforming was analyzed by employing axial feed on the tube ends. It is found that hydroforming FSW tube is a new deal and does show a few peculiarities. The FSW tube exhibits a spiral weld and the basin-shaped nugget. Fine-grained structure is retained during tube forming. The thinning of the tube in axial direction shows M-shaped distribution during hydroforming. The severe thinning is observed at one quarter of the expansion zone from symmetry plane. In the hoop direction, the base material near the weld suffers severe thinning due to the high hoop and axial tensile stress. The thickness distribution greatly depends on the sequence of the contacting die and the variations of the curvature radius of the tube during hydroforming. Moreover, the weld shows an inhibitory effect for the generation of the wrinkles and decreases the number of the wrinkles as compared to the seamless tube during hydroforming. This effect is more obvious when the forming pressure is lower.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Dohmann F, Hartl C (1996) Hydroforming—a method to manufacture light-weight parts. J Mater Process Technol 60:669–676
Chu GN, Liu G, Liu WJ, Yuan SJ (2012) An approach to improve thickness uniformity. Int J Adv Manuf Technol 60:1247–1253
Alaswad A, Benyounis KY, Olabi AG (2012) Tube hydroforming process: a reference guide. Mater Des 33:328–339
Buffa G, Fratini L, Hua J, Shivpuri R (2006) Friction stir welding of tailored blanks: investigation on process feasibility. CIRP Ann 55:279–282
Sato YS, Sugiura Y, Shoji Y, Park SHC, Kokawa H, Ikeda K (2004) Post-weld formability of friction stir welded Al alloy 5052. Mater Sci Eng A 369:138–143
Miles MP, Decker BJ, Nelson TW (2004) Formability and strength of friction-stir-welded aluminum sheets. Metall Mater Trans A 35A:3461–3468
Fratini L, Piacentini M (2006) Friction stir welding of 3d industrial parts: joint strength analysis. In: ASME proceedings of the 8th biennial conference on engineering systems design and analysis. Turino, pp 763-770
Dubourg L, Gholipour J, Jahazi M (2008) Friction stir welding of 2024-T3 aluminum tubes for hydroforming application. In: Trends in welding research, proceedings of the 8th international conference. Pine Mountain, GA, pp 549–556
Marré M, Ruhstorfer M, Tekkaya AE, Zaeh MF (2009) Manufacturing of lightweight frame structures by innovative joining by forming processes. Int J Mater Form 2:307–310
Urso GD, Longo M, Giardini C (2013) Mechanical and metallurgical analyses of longitudinally friction stir welded tubes: the effect of process parameters. Int J Mater Prod Technol 46:177–196
Urso GD, Longo M, Giardini C (2011) Characterization of friction stir welded tubes by means of tube bulge test. The 14th international esaform conference on material forming: ESAFORM 1353: 1259–1264.
Leitao C, Leal RM, Rodrigues DM, Loureiro A, Vilaca P (2009) Tensile behavior of similar and dissimilar AA5182-H111 and AA6016-T4 thin friction stir welds. Mater Des 30:101–108
Aval HJ, Serajzadeh S (2014) A study on natural aging behavior and mechanical properties of friction stir-welded AA6061-T6 plates. Int J Adv Manuf Technol 71:933–941
Ipekoglu G, Erim S, Cam G (2014) Effects of temper condition and post weld heat treatment on the microstructure and mechanical properties of friction stir butt-welded AA7075 Al alloy plates. Int J Adv Manuf Technol 70:201–213
Silva MB, Skjoedt M, Vilaca P, Bay N, Martins PAF (2009) Single point incremental forming of tailored blanks produced by friction stir welding. J Mater Process Technol 209:811–820
Kim DY, Lee W, Kim JY, Chung KH, Kim CM, Okamoto K, Wagoner RH, Chung K (2010) Macro-performance evaluation of friction stir welded automotive tailor-welded blank sheets: part II – formability. Int J Solids Struct 47:1063–1081
Ramulu PJ, Ganesh NR, Kailas SV (2013) Forming limit investigation of friction stir welded sheets: influence of shoulder diameter and plunge depth. Int J Adv Manuf Technol 69:2757--2772
Hu ZL, Yuan SJ, Wang XS, Liu G, Huang YX (2011) Effect of post-weld heat treatment on the microstructure and plastic deformation behavior of friction stir welded 2024. Mater Des 32:5055–5060
Hu ZL, Yuan SJ, Wang XS, Liu G, Liu HJ (2012) Microstructure and mechanical properties of Al–Cu–Mg alloy tube fabricated by friction stir welding and tube spinning. Scr Mater 55:637–640
Yuan SJ, Hu ZL, Wang XS (2012) Evaluation of formability and material characteristics of aluminum alloy friction stir welded tube produced by a novel process. Mater Sci Eng A 543:210–216
Fatemi A, Morovvati MR, Biglari FR (2013) The effect of tube material, microstructure, and heat treatment on process responses of tube hydroforming without axial force. Int J Adv Manuf Technol 68:263–276
Kuwabara T (2007) Advances in experiments on metal sheets and tubes in support of constitutive modeling and forming simulations. Int J Plast 23:385–419
Kuwabara T, Yoshida K, Narihara K (2005) Anisotropic plastic deformation of extruded aluminum alloy tube under axial forces and internal pressure. Int J Plast 21:101–117
Jansson M, Nilsson L, Simonsson K (2005) On constitutive modeling of aluminum alloys for tube hydroforming applications. Int J Plast 21:1041–1058
Barlat F, Lian J (1989) Plasticity behavior and stretchability of sheet metals Part 1: a yield function for orthotropic sheets under plane stress conditions. Int J Plast 5:51–66
Lang LH, Yuan SJ, Wang ZR, Wang XS, Danckert J, Nielsen KB (2004) Experimental and numerical investigation into useful wrinkling during aluminum alloy internal high-pressure forming. Proc IME B J Eng Manufact 218:43–49
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Hu, Z.L., Wang, X.S., Pang, Q. et al. Experimental and numerical study on hydroforming characteristics of friction stir welded aluminum alloy tubes. Int J Adv Manuf Technol 80, 959–969 (2015). https://doi.org/10.1007/s00170-014-6613-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-014-6613-x