Abstract
The coordinate measuring machine (CMM) is among the powerful tools used to measure the conformity of the mechanical parts. The performance of this machine is partly affected by geometric errors associated to its articulations. To provide remedial actions to the CMM in case of non-conformity, we propose a method to identify geometric errors characterizing the machine using the inverse method, when measuring a ball step-gauge in seven locations as defined in the ASME 89.4.10360.2-2008 standard and nineteen positions proposed by G. Zhang.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Cauchick-Miguel, P., Kinga, T., Davis, J.: CMM verification: a survey. Measurement 17(1), 1–16 (1996)
Sartori, S., Zhang, G.X.: Geometric error measurement and compensation of machines. CIRP Ann. Manuf. Technol. 44(2), 599–609 (1995)
Lim, C.K., Burdekin, M.: Rapid volumetric calibration of coordinate measuring machines using a hole bar artefact. Proc. Inst. Mech. Eng. Part B J. Eng. Manuf. 216(8), 1083–1093 (2002)
ASME89.4.10360.2-2008: Acceptance test and reverification test for CMMs – Part 2: CMMs used for measuring linear dimensions (2008)
Zhang, G., Ouyang, R., Lu, B., Hocken, R., Veale, R., Donmez, A.: A displacement method for machine geometry calibration. CIRP Ann. Manuf. Technol. 37(1), 515–518 (1988)
Curran, E., Phelan, P.: Quick check error verification of coordinate measuring machines. J. Mater. Process. Technol. 155–156, 1207–1213 (2004)
Nafi, A., Mayer, J.R.R.: Identification of scale and squareness errors on a CMM using a step gauge measured based on the ASME 89.4.10360.2-2008 standard. Trans. North Am. Manuf. Res. Inst. SME 38, 325–332 (2010)
Schwenke, H., Franke, M., Hannaford, J., Kunzmann, H.: Error mapping of CMMs and machine tools by a single tracking interferometer. CIRP Ann. Manuf. Technol. 54(1), 475–478 (2005)
Schwenke, H., Knapp, W., Haitjema, H., Weckenmann, A., Schmitt, R., Delbressine, F.: Geometric error measurement and compensation of machines—an update. CIRP Ann. Manuf. Technol. 57(2), 660–675 (2008)
Kruth, J.-P., Zhou, L., Van den Bergh, C., Vanherck, P.: A method for squareness error verification on a coordinate measuring machine. Int. J. Adv. Manuf. Technol. 21, 874–878 (2003)
Osawa, S., Takatsuji, T., Noguchi, H., Kurosawa, T.: Development of a ball step-gauge and an interferometric stepper used for ball-plate calibration. Precis. Eng. 26(2), 214–221 (2002)
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer International Publishing AG, part of Springer Nature
About this paper
Cite this paper
Laaouina, L., Nafi, A., Mouchtachi, A. (2019). Prediction of Coordinate Measuring Machines Geometric Errors by Measuring a Ball Step-Gauge. In: Mizera-Pietraszko, J., Pichappan, P., Mohamed, L. (eds) Lecture Notes in Real-Time Intelligent Systems. RTIS 2017. Advances in Intelligent Systems and Computing, vol 756. Springer, Cham. https://doi.org/10.1007/978-3-319-91337-7_17
Download citation
DOI: https://doi.org/10.1007/978-3-319-91337-7_17
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-91336-0
Online ISBN: 978-3-319-91337-7
eBook Packages: Intelligent Technologies and RoboticsIntelligent Technologies and Robotics (R0)