Editorial:Polymer Fibres 2000 The Manchester Conference Centre, Manchester, UK, 5-7 July 2000 Robert J. Young Editorial Introduction Pages: 3069 - 3069
Studies of the mesophase development in polymeric fibers during deformation by synchrotron SAXS/WAXD Shaofeng RanXinhua ZongR. A. Phillips OriginalPaper Pages: 3071 - 3077
Single fibre deformation studies of poly(p-phenylene benzobisoxazole) fibres part I Determination of Crystal Modulus R. J. DaviesM. A. Montes-MoránR. J. Young OriginalPaper Pages: 3079 - 3087
Electrically conductive PANi multifilaments spun by a wet-spinning process J. ZhouG. TzamalisA. P. Monkman OriginalPaper Pages: 3089 - 3095
The application of factorial experimental design to the processing of polypropylene fibres R. D. YangR. R. MatherA. F. Fotheringham OriginalPaper Pages: 3097 - 3101
Reactive extrusion and melt spinning—A new technological route to special fibres R. BeyreutherB. TändlerR. Vogel OriginalPaper Pages: 3103 - 3111
Neural modelling of polypropylene fibre processing: Predicting the structure and properties and identifying the control parameters for specified fibres G. AllanR. YangR. Mather OriginalPaper Pages: 3113 - 3118
Drawability and attainable mechanical properties of polyamide yarn using true stress–true strain curves J. Van RuitenR. RiedelJ. P. Penning OriginalPaper Pages: 3119 - 3128
Deformation mechanisms in cellulose fibres, paper and wood S. J. EichhornJ. SirichaisitR. J. Young OriginalPaper Pages: 3129 - 3135
Ballistic protection mechanisms in personal armour M. J. N. JacobsJ. L. J. Van Dingenen OriginalPaper Pages: 3137 - 3142
The role of pressure annealing in improving the stiffness of polyethylene/hydroxyapatite composites A. P. UnwinI. M. WardJ. Weng OriginalPaper Pages: 3165 - 3177
Fabrication and characteristics of AA6061/SiCp composites by pressureless infiltration technique K. B. LeeH. S. SimH. Kwon OriginalPaper Pages: 3179 - 3188
Improved contacting by the use of silver in solid oxide fuel cells up to an operating temperature of 800 °C W. A. MeulenbergO. TellerD. Stöver OriginalPaper Pages: 3189 - 3195
Phase transformation reactions in rapidly solidified Al-6.5Fe-1.5V alloys R. TongsriE. J. MinayH. B. Mcshane OriginalPaper Pages: 3197 - 3206
Structure formation and miscibility of sheets from PBT and LCP blends K. QiK. Nakayama OriginalPaper Pages: 3207 - 3213
Surface effects in chromate conversion coatings on 2024-T3 aluminum alloy X. SunR. LiT. Foster OriginalPaper Pages: 3215 - 3220
Nanostructured thin palladium-silver membranes: Effects of grain size on gas permeation properties B. A. McCoolY. S. Lin OriginalPaper Pages: 3221 - 3227
Application of equal channel angular extrusion on strengthening of ferritic stainless steel N. SaitoM. MabuchiM. Nakamura OriginalPaper Pages: 3229 - 3232
Synthesis of tungsten monocarbide by self-propagating high-temperature synthesis in the presence of an activative additive J. ZhangJ. H. LeeC. W. Won OriginalPaper Pages: 3233 - 3238
The influence of Poisson contraction on matrix cracking stress in fiber reinforced ceramics Yih-Cherng Chiang OriginalPaper Pages: 3239 - 3246
The effect of Co2+ on the structure and colour of silica gel derived materials M. G. Ferreira Da Silva OriginalPaper Pages: 3247 - 3251
Hydroxy- and fluorapatite films on Ti alloy substrates: Sol-gel preparation and characterization M. CavalliG. GnappiM. Fini OriginalPaper Pages: 3253 - 3260
Non-equilibrium solidification by laser surface alloying of molybdenum with nickel: Structure and properties of alloyed layers R. PawlakZ. GawronskiK. Wissenbach OriginalPaper Pages: 3261 - 3271
Ultrafine zinc oxide powders prepared by precipitation/mechanical milling H. M. DengJ. DingJ. Wang OriginalPaper Pages: 3273 - 3276
Low-temperature chemical synthesis of lanthanum copper oxide Xiaohui WangYanchun Zhou OriginalPaper Pages: 3277 - 3282
Effect of process parameters on synthesis of aluminum nitride powder prepared by chemical vapor deposition Moo-Chin WangMing-Sung TsaiNan-Chung Wu OriginalPaper Pages: 3283 - 3289
Effects of excess Te on the thermoelectric properties of p-type 25% Bi2Te3-75% Sb2Te3 single crystal and hot-pressed sinter Chang-Won HwangDow-Bin HyunTae Sung Oh OriginalPaper Pages: 3291 - 3297
Formation of niobium-tantalum pentoxide orthorhombic solid solutions under chlorine-bearing atmospheres J. GonzalezM. Del C. RuizA. Bohé OriginalPaper Pages: 3299 - 3311
Processing of composites in the Ti-Si-C system C.-S. ParkF. ZhengR. K. Bordia OriginalPaper Pages: 3313 - 3322
Hydroxyapatite-316L fibre composites prepared by vibration assisted slip casting X. MiaoA. J. RuysB. K. Milthorpe OriginalPaper Pages: 3323 - 3332