Volume 26, issue 1, January 2013

25 articles in this issue

Driving and braking control of PM synchronous motor based on low-resolution hall sensor for battery electric vehicle

Authors (first, second and last of 6)
- Jing Gu
- Minggao Ouyang
- Yan Ma
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 1 - 10
Adaptive PI control strategy for flat permanent magnet linear synchronous motor vibration suppression

Authors (first, second and last of 4)
- Fanwei Meng
- Chengying Liu
- Liping Wang
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 11 - 20
Vision-based stabilization of nonholonomic mobile robots by integrating sliding-mode control and adaptive approach

Authors
- Zhengcai Cao
- Longjie Yin
- Yili Fu
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 21 - 28
Accuracy analysis of Stewart platform based on interval analysis method

Authors
- Rui Yao
- Wenbai Zhu
- Peng Huang
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 29 - 34
Design and analysis of a new AUV’s sliding control system based on dynamic boundary layer

Authors
- Fudong Gao
- Cunyun Pan
- Yanyan Han
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 35 - 45
Numerical prediction and performance experiment in a deep-well centrifugal pump with different impeller outlet width

Authors (first, second and last of 5)
- Weidong Shi
- Ling Zhou
- Tao Lang
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 46 - 52
Numerical simulation and analysis of solid-liquid two-phase flow in centrifugal pump

Authors (first, second and last of 5)
- Yuliang Zhang
- Yi Li
- Huashu Dou
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 53 - 60
Real gas effects on charging and discharging processes of high pressure pneumatics

Authors
- Yuxi Luo
- Xuanyin Wang
- Yaozheng Ge
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 61 - 68
Effect of honeycomb seals on loss characteristics in shroud cavities of an axial turbine

Authors
- Jie Gao
- Qun Zheng
- Zheng Wang
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 69 - 77
Flow dynamics of a spiral-groove dry-gas seal

Authors
- Bing Wang
- Huiqiang Zhang
- Hongjun Cao
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 78 - 84
Fluid-solid interaction model for hydraulic reciprocating O-ring seals

Authors (first, second and last of 5)
- Chuanjun Liao
- Weifeng Huang
- Ying Liu
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 85 - 94
Unbalance vibratory displacement compensation for active magnetic bearings

Authors
- Hui Gao
- Longxiang Xu
- Yili Zhu
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 95 - 103
Dynamic responses of rotor drops onto double-decker catcher bearing

Authors
- Yili Zhu
- Chaowu Jin
- Longxiang Xu
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 104 - 113
Synergistic effect between nano-ceramic lubricating additives and electroless deposited Ni-W-P coating

Authors (first, second and last of 4)
- Min Chen
- Wushan Cheng
- Xiaobo Huang
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 114 - 120
Numerical analysis of Nd:YAG pulsed laser polishing CVD self-standing diamond film

Authors (first, second and last of 6)
- Feng Xu
- Haifeng Hu
- Min Wang
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 121 - 127
Fractal prediction model of thermal contact conductance of rough surfaces

Authors
- Cuicui Ji
- Hua Zhu
- Wei Jiang
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 128 - 136
Fractal characteristics and microstructure evolution of magnetron sputtering Cu thin films

Authors
- Shiwen Du
- Yongtang Li
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 137 - 143
Coupled dynamic modeling of rolls model and metal model for four high mill based on strip crown control

Authors
- Jianliang Sun
- Yan Peng
- Hongmin Liu
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 144 - 150
Precision design for machine tool based on error prediction

Authors
- Qiang Huang
- Genbao Zhang
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 151 - 157
Temperature variable optimization for precision machine tool thermal error compensation on optimal threshold

Authors (first, second and last of 5)
- Ting Zhang
- Wenhua Ye
- Xiaolan Yang
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 158 - 165
Algorithm for detecting volumetric geometric accuracy of NC machine tool by laser tracker

Authors
- Jindong Wang
- Junjie Guo
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 166 - 175
Multi-segment and multi-ply overlapping process of multi coupled activities based on valid information evolution

Authors
- Zhiliang Wang
- Yunxia Wang
- Shenghai Qiu
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 176 - 188
Reconfigurable modeling technology of similar-structure products configuration design

Authors (first, second and last of 4)
- Lemiao Qiu
- Bin Ren
- Jian Xu
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 189 - 196
Topology recovery technique for complex freeform surface model after local geometry repair

Authors
- Keke Bian
- Yinglin Ke
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 197 - 206
Analysis of oil consumption in cylinder of diesel engine for optimization of piston rings

Authors (first, second and last of 5)
- Junhong Zhang
- Guichang Zhang
- Hai Liu
- Content type: OriginalPaper
- Published: 01 February 2013
- Pages: 207 - 216

Volume 26, issue 1, January 2013

Driving and braking control of PM synchronous motor based on low-resolution hall sensor for battery electric vehicle

Adaptive PI control strategy for flat permanent magnet linear synchronous motor vibration suppression

Vision-based stabilization of nonholonomic mobile robots by integrating sliding-mode control and adaptive approach

Accuracy analysis of Stewart platform based on interval analysis method

Design and analysis of a new AUV’s sliding control system based on dynamic boundary layer

Numerical prediction and performance experiment in a deep-well centrifugal pump with different impeller outlet width

Numerical simulation and analysis of solid-liquid two-phase flow in centrifugal pump

Real gas effects on charging and discharging processes of high pressure pneumatics

Effect of honeycomb seals on loss characteristics in shroud cavities of an axial turbine

Flow dynamics of a spiral-groove dry-gas seal

Fluid-solid interaction model for hydraulic reciprocating O-ring seals

Unbalance vibratory displacement compensation for active magnetic bearings

Dynamic responses of rotor drops onto double-decker catcher bearing

Synergistic effect between nano-ceramic lubricating additives and electroless deposited Ni-W-P coating

Numerical analysis of Nd:YAG pulsed laser polishing CVD self-standing diamond film

Fractal prediction model of thermal contact conductance of rough surfaces

Fractal characteristics and microstructure evolution of magnetron sputtering Cu thin films

Coupled dynamic modeling of rolls model and metal model for four high mill based on strip crown control

Precision design for machine tool based on error prediction

Temperature variable optimization for precision machine tool thermal error compensation on optimal threshold

Algorithm for detecting volumetric geometric accuracy of NC machine tool by laser tracker

Multi-segment and multi-ply overlapping process of multi coupled activities based on valid information evolution

Reconfigurable modeling technology of similar-structure products configuration design

Topology recovery technique for complex freeform surface model after local geometry repair

Analysis of oil consumption in cylinder of diesel engine for optimization of piston rings

For authors

Explore

Navigation

Volume 26, issue 1, January 2013

Authors (first, second and last of 6)

Authors (first, second and last of 4)

Authors

Authors

Authors

Authors (first, second and last of 5)

Authors (first, second and last of 5)

Authors

Authors

Authors

Authors (first, second and last of 5)

Authors

Authors

Authors (first, second and last of 4)

Authors (first, second and last of 6)

Authors

Authors

Authors

Authors

Authors (first, second and last of 5)

Authors

Authors

Authors (first, second and last of 4)

Authors

Authors (first, second and last of 5)

For authors

Explore

Search

Navigation