Abstract
Background
In this research, response surface methodology (RSM) was applied to optimize Reactive Blue 19 removal by activated carbon from pomegranate residual. A 24 full factorial central composite design (CCD) was applied to evaluate the effects of initial pH, adsorbent dose, initial dye concentration, and contact time on the dye removal efficiency.
Methodology
The activated carbon prepared by 50 wt.% phosphoric acid activation under air condition at 500°C. The range of pH and initial dye concentration were selected in a way that considered a wide range of those variables. Furthermore, the range of contact time and adsorbent dose were determined based on initial tests. Levels of selected variables and 31 experiments were determined. MiniTab (version 16.1) was used for the regression and graphical analyses of the data obtained.
Results
It was found that the decrease of initial dye concentration and the increase of initial pH, adsorbent dose, and contact time are beneficial for improving the dye removal efficiency. Analysis of variance (ANOVA) results presented high R2 value of 99.17% for Reactive Blue 19 dye removal, which indicates the accuracy of the polynomial model is acceptable.
Conclusions
Initial pH of 11, adsorbent dose of 1.025 g/L, initial dye concentration of 100 mg/L, and contact time of 6.8 minutes found to be the optimum conditions. Dye removal efficiency of 98.7% was observed experimentally at optimum point which confirmed close to model predicted (98.1%) result.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
Many industries, especially textile and food industries often use dyes and pigments to color their products. As a result, these industries often discharge large amounts of colored effluents due to unfixed dyes on fibres or food during coloring and washing steps [1]. Due to the disposal of these effluents into the receiving water body may cause severe damage to aquatic biota and humans due to mutagenic and carcinogenic effects [2–4], it is of great importance to provide waste-treatment facilities for minimizing these substances in the effluents before discharge.
There are several methods available for treatment of dye-containing wastewater, such as membrane [5], electrochemical [6], coagulation/flocculation [7], and biological [8]. The adsorption technique has been found not only to be effective, but also practical in application for the dye-containing wastewater treatment, due to its high efficiency, simplicity, ease of operation, and the availability of a wide range of adsorbents [9, 10]. Activated carbons (ACs) are widely used as the most efficient adsorbents. The chemical activation is often used to produce ACs and it involves mixing the feedstock with a chemical activating agent such as H3PO4, ZnCl2, and KOH [11–13].
Conventional and classical methods of studying a process by maintaining other factors involved at an unspecified constant level does not depict the combined effect of all the factors involved. Response Surface Methodology (RSM) is a collection of mathematical and statistical techniques useful for developing, improving, and optimizing processes and can be used to evaluate the relative significance of several affecting factors even in the presence of complex interactions. The main objective of RSM is to determine the optimum operational conditions for the system or to determine a region that satisfies the operating specifications [14]. Many research groups applied this method for removal of different pollutants by adsorption process [14–19].
The aim of the present study is to optimize and model the removal of Reactive Blue 19 from aqueous solution by activated carbon derived from pomegranate residual using RSM. The relationship between dye removal efficiency and four main independent parameters including initial pH, initial dye concentration, adsorbent dose, and contact time were evaluated by applying central composite design (CCD).
Methods
Materials and activated carbon preparation
Dye solution was prepared by dissolving Reactive blue 19 (RB19) which was provided by the Alvan Sabet Company and is widely used in textile industries in Iran. The chemical structure and characteristics of the selected dye is presented in Table 1. The solution pH measurement was carried out using a 340i/SET pH meter (WTW-Germany) and was adjusted by 1 M hydrochloric acid or 1 M sodium hydroxide. The dye solution and adsorbent was agitated by a jar test at 150 rpm agitation speed at ambient temperature 25°C. A six beaker jar test apparatus from Zag-Chemi Company in Iran was used to simulate the adsorption process. All samples were filtered through glass fibre filters GF/A. The clear supernatants were analyzed for RB19 dye concentrations using a UV–vis HACH spectrophotometer (DR/4000).
In this study, pomegranate residual was collected from Meykhosh juice industry in Yazd/Iran. Pomegranate residual has been dried in an oven for 2 h at 100°C until a constant weight was reached. It was then ground in a ball mill and passed through sieve No.8. They were soaked for 24 h in the ratio of 1:1 (w/v) with 50 wt.% phosphoric acid at room temperature. The sample is then decanted, dried in a muffle furnace for 1 h at 500°C. Then the samples were washed sequentially several times with hot distilled water, until pH of the washing solution became neutral. In the last step, activated carbon (AC) was powder and sieved by the No. 200 mesh.
The textural properties of adsorbent were also tested by N2 adsorption/desorption isotherms at 77 K using an Autosorb 1 analyzer (Quantachrome Corporation, USA). The specific surface area (SBET) was calculated by Brun- auer–Emmett–Teller (BET) method. The textural characteristics of AC are shown in Table 2. The pore size distribution was determined by using the Barrett–Joyner– Halenda (BJH) method (Figure 1).
Experimental design
A central composite design (CCD) was employed for determining the optimum condition for the dye removal. A total of 31 experiments were carried out according to a 24 full factorial CCD, consisting of 16 factorial experiments (coded to the usual ± 1 notation), 8 axial experiments (on the axis at a distance of ± α from the center), and 7 replicates (at the center of the experimental domain).
The value of α for rotatability depends on the number of points in the factorial portion of the design, which is given in equation (1):
where NF is the number of points in the cube portion of the design (NF =2k, k is the number of factors). Therefore, α is equal to (24)1/4 = 2 according to equation (1).
The range of pH and initial dye concentration were selected in a way that considered a wide range of those variables. The dye concentration was selected between 100 to 500 mg/L. This range is based on determined actual concentration of textile wastewaters in Iran. The range of contact time and adsorbent dose were determined based on initial tests. The results of initial tests are shown in Figure 2. As demonstrated in the figures, the dye was rapidly adsorbed at a high rate in the first 5 minute, and after 10 minutes leveled off. Therefore, the range of contact time was considered between 1 minute and 10 minutes. Due to a slight difference between dye removal efficiencies for adsorbent dose of 2 g/L and 1.75 g/L, the maximum amount of adsorbent dose was considered 1.75 g/L. In addition, adsorbent dose of lower than 0.75 g/L was not enough efficient to remove RB19.
Levels of selected variables are presented in Table 3. For statistical calculations, the variables Xi (the real value of an independent variable) were coded as xi (dimensionless value of an independent variable) according to equation (2):
where X0 is the value of Xi at the center point and ΔX represents the step change.
The behavior of the adsorption process is explained by the following empirical second-order polynomial model equation (3):
where Y is the predicted response (dye removal efficiency), b0 the constant coefficient, bi the linear coefficients, bii the quadratic coefficients, bij the interaction coefficients and xi, xj are the coded values of the variables. MiniTab (version 16.1) was used for the regression and graphical analyses of the data obtained. The reliability of the fitted model was justified through ANOVA and the coefficient of R2.
Results
Statistical analysis
The experimental design matrix, the experimental results and the predicted dye removal efficiency are presented in Table 4. The final model is expressed by equation (4):
Statistical regression coefficients for RB19 dye removal efficiency (%) is provided in Table 5. Amounts of P (P < 0.05) for all independent parameters confirms that four selected factors are significant. However, it was found that all square and interaction terms except x12 and x22 (P values of 0.000) were insignificant to the response. ANOVA for the selected dye removal is also listed in Table 6. In this case, the P-value of 0.000 (P < 0.05) for regression model equation implies that the second-order polynomial model fitted to the experimental results well. The lack-of-fit was also calculated from the experimental error (pure error) and residuals. “F-value of Lack-of-fit” of 2.24 implies the significance of model correlation between the variables and process response for dye removal. Additionally, the value of R2 = 99.17% and R2 (adj) =98.44% confirm the accuracy of the model. Furthermore, parity plot for the experimental and predicted value of RB19 removal efficiency (%) is demonstrated in Figure 3.
In addition, normal probability and residuals versus fitted values plots for RB19 removal efficiency are illustrated in Figure 4. Normal probability plot is a suitable graphical method for judging the normality of the residuals [18]. As seen in Figure 4(a), the normality assumption was relatively satisfied as the points in the plot form a fairly straight line. The reliability of the model was also examined with the plot of residuals versus fits in Figure 4(b). As Figure 4(b) shows, the number of increasing or decreasing points was significantly close; patterns of increasing residuals and increasing fits were similar; and, positive and negative residuals were scattered in same range. As a result, Figure 4 shows that the model is adequate to describe RB19 removal efficiency by response surface methodology for AC.
Response surface and counter plotting for evaluation of operational parameters
The main effect of each parameter on the dye removal efficiency is showed in Figure 5. As illustrated in Figure 5(a, b, c), by increasing of initial pH and adsorbent dose, and decreasing of initial dye concentration, the dye removal efficiency improved. Moreover, as shown in Figure 5(d), adsorption efficiency rapidly increased with an increase in contact time within the first minutes. Then, the rate of adsorption was found to be relatively slow and then constant. As shown in this Figure, the dye removal is highly dependent on adsorbent dose and initial dye concentration, and the initial pH and contact time slightly influenced the process efficiency.
For a better explanation of the independent variables and their interactive effects on the dye removal, 3D plots and its corresponding contour plots are represented in Figure 6. At constant value of the initial dye concentration (300 mg/L), when the adsorbent dose and initial pH increase, the dye removal efficiency increases and finally reaches to 100% (Figure 6(a)). Moreover, for given initial dye concentration of 100 mg/L and adsorbent dose of 1.25 g/L, dye removal efficiency is almost independent of initial pH (Figure 6(b)). This independency is due to the existence of numerous active sites for the adsorption, whereas the independency was decreased with increasing of initial dye concentration. As shown in Figure 6(c), there are no significant changes on the dye removal surface with the increase of contact time and initial pH.
Process optimization
In order to determine the optimum conditions by the adsorption process, the desired aim in terms of RB19 removal efficiency was defined as target to achieve 98% removal efficiency. The optimum values of the process parameters were calculated in coded units (xi) and then converted into uncoded units (Xi) using Equation ([1]). Initial pH of 11, adsorbent dose of 1.025 g/L, initial dye concentration of 100 mg/L and contact time of 6.8 minutes found to be the optimum conditions by the model. The optimum condition was repeated three times and dye removal efficiencies of 98.4, 98.6, and 99.1% were resulted. The average of 98.7% dye removal efficiency was found close to the model prediction of 98.1%.
Discussion
According to the results, contact time is the least important parameter, which is reported by other research groups [20, 21]. Furthermore, by increasing of initial pH and adsorbent dose, and decreasing of initial dye concentration, the dye removal efficiency improved. These results are in good agreement with of previous studies [22, 23].
The effect of the four selected independent parameters and interactions among the RSM were analyzed which was shown that some interactions like (x12 and x22) influenced the adsorption performance as well as all selected parameters. ANOVA showed a high R2 value of regressions model equation (R2 = 0.9917), thus ensuring a satisfactory adjustment of the second-order regression model with the experimental data. The optimum RB19 removal efficiency were found at initial pH of 11, adsorbent dose of 1.025 g/L, initial dye concentration of 100 mg/l and contact time of 6.8 min. An experiment was performed in optimum conditions which confirmed that the model and experimental results are in close agreement (98.7% compared to 98.1% for the model).
Conclusions
In this research, response surface methodology was applied as an experimental design to explore the optimal conditions for RB19 dye removal from aqueous solutions by activated carbon prepared by pomegranate residual. The effect of four operating variables of adsorption process including initial pH, adsorbent dose, initial dye concentration, and contact time were examined. The BET method showed that the average SBET of AC was 825.46 m2 g−1. The results of this investigation presented that RSM is a powerful statistical optimization and modeling tool for RB19 removal using adsorption process.
References
Santos SCR, Boaventura RAR: Adsorption modeling of textile dyes by sepiolite. Appl Clay Sci 2008, 42: 137–145. 10.1016/j.clay.2008.01.002
Crini G: Non-conventional low-cost adsorbents for dye removal: a review. Bioresour Technol 2006, 97: 1061–1085. 10.1016/j.biortech.2005.05.001
Sadri MS, Alavi Moghaddam MR, Arami M: Decolorization of an acidic dye from synthetic wastewater by sludge of water treatment plant. Iran J Environ Health Sci Eng 2010, 7: 437–442.
Ehrampoush MH, Ghanizadeh G, Ghaneian MT: Equilibrium and kinetics study of reactive red 123 dye removal from aqueous solution by adsorption on eggshell. Iran J Environ Health Sci Eng 2011, 8: 101–108.
Xu Y, Lebrun RE: Treatment of textile dye plant effluent by nanofiltration membrane. Separa Sci Technol 1999, 34: 2501–2519. 10.1081/SS-100100787
Bechtold T, Burtscher E, Turcanu A: Cathodic decolorisation of textile wastewater containing reactive dyes using multi-cathode electrolyser. J Chem Technol Biotechnol 2001, 76: 303–311. 10.1002/jctb.383
Sadri MS, Alavi Moghaddam MR, Arami M: Coagulation/flocculation process for dye removal using sludge from water treatment plant: optimization through response surface methodology. J Hazard Mater 2010, 175: 651–657. 10.1016/j.jhazmat.2009.10.058
Hosseini KE, Alavi Moghaddam MR, Hashemi SH: Investigation of decolorization kinetics and biodegradation of azo dye Acid Red 18 using sequential process of anaerobic sequencing batch reactor/moving bed sequencing batch biofilm reactor. Int Biodeter Biodeg 2012, 71: 43–49.
Chatterjee S, Lee DS, Lee MW, Woo SH: Enhanced adsorption of congo red from aqueous solutions by chitosan hydrogel beads impregnated with cetyl trimethyl ammonium bromide. Bioresour Technol 2009, 100: 2803–2809. 10.1016/j.biortech.2008.12.035
Samarghandi MR, Zarrabi M, Noori Sepehr M, Amrane A, Hossein Safari G, Bashiri S: Application of acidic treated pumice as an adsorbent for the removal of azo dye from aqueous solutions: kinetic, equilibrium and thermodynamic studies. Iran J Environ Health Sci Eng 2012, 9: 101–108.
Lua AC, Yang T: Characteristics of activated carbon prepared from pistachio-nut shell by zinc chloride activation under nitrogen and vacuum conditions. J Colloid Inter Sci 2005, 290: 505–513. 10.1016/j.jcis.2005.04.063
Benadjemia M, Millière L, Reinert L, Benderdouche N, Duclaux L: Preparation, characterization and Methylene Blue adsorption of phosphoric acid activated carbons from globe artichoke leaves. Fuel Process Technol 2011, 92: 1203–1212. 10.1016/j.fuproc.2011.01.014
Wu FC, Wu PH, Tseng RL, Juang RS: Preparation of activated carbons from unburnt coal in bottom ash with KOH activation for liquid-phase adsorption. J Environ Manage 2010, 91: 1097–1102. 10.1016/j.jenvman.2009.12.011
Ravikumar K, Ramalingam S, Krishnan S, Balu K: Application of response surface methodology to optimize the process variables for reactive red and acid brown dye removal using a novel adsorbent. Dyes Pigment 2006, 70: 18–26. 10.1016/j.dyepig.2005.02.004
Auta M, Hameed BH: Optimized waste tea activated carbon for adsorption of methylene blue and acid blue 29 dyes using response surface methodology. Chem Eng J 2011, 175: 233–243.
Liu Y, Wang J, Zheng Y, Wang A: Adsorption of methylene blue by kapok fiber treated by sodium chlorite optimized with response surface methodology. Chem Eng J 2012, 184: 248–255.
Chatterjee S, Kumar A, Basu S, Dutta S: Application of response surface methodology for methylene blue dye removal from aqueous solution using low cost adsorbent. Chem Eng J 2012, 181: 289–299.
Azizi A, Alavi Moghaddam MR, Arami M: Application of wood waste for a reactive dye removal from aqueous solutions: optimization through response surface methodology. J Environ Eng Manag in press
Liu Y, Zheng Y, Wang A: Response surface methodology for optimizing adsorption process parameters for methylene blue removal by a hydrogel composite. Adsorp Sci Technol 2010, 28: 913–922. 10.1260/0263-6174.28.10.913
Azizi A, Alavi Moghaddam MR, Arami M: Wood Waste from mazandaran wood and the paper industry as a low cost adsorbent for removal of a reactive dye. J Resid Sci Technol 2011, 8: 21–28.
Khaled A, Nemr AE, Sikaily AE, Abdelwahab O: Removal of direct N blue-106 from artificial textile dye effluent using activated carbon from orange peel: adsorption isotherm and kinetic studies. J Hazard Mater 2009, 165: 100–110. 10.1016/j.jhazmat.2008.09.122
Mahmoodi NM, Hayati B, Arami M, Lan C: Adsorption of textile dyes on pine cone from colored wastewater: kinetic, equilibrium and thermodynamic studies. Desalination 2011, 268: 117–125. 10.1016/j.desal.2010.10.007
Sadri MS, Alavi Moghaddam MR, Aram M: A comparative study of acid red 119 dye adsorption onto dried sewage sludge and sewage sludge ash: isotherm, kinetic and desorption study. J Resid Sci Technol 2010, 7: 199–207.
Acknowledgements
The authors are grateful to the Amirkabir University of Technology (AUT) research fund for the financial support. In addition, the authors wish to express thanks to Ms. Armineh Azizi and Ms. Shabnam Sadri Moghaddam (PhD students of environmental engineering), and Ms. Lida Ezzedinloo for their assistance during experiments.
Author information
Authors and Affiliations
Corresponding author
Additional information
Competing interests
The authors declare that they have no competing interests.
Authors’ contributions
This work is part of the Master thesis of ER where MRA, Supervisor of the thesis, suggested the problem and read the paper and MR, Co-Supervisor of the thesis, helped in analysis of experiments. All authors read and approved the final manuscript.
Authors’ original submitted files for images
Below are the links to the authors’ original submitted files for images.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 2.0 International License ( https://creativecommons.org/licenses/by/2.0 ), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
About this article
Cite this article
Radaei, E., Alavi Moghaddam, M.R. & Arami, M. Removal of reactive blue 19 from aqueous solution by pomegranate residual-based activated carbon: optimization by response surface methodology. J Environ Health Sci Engineer 12, 65 (2014). https://doi.org/10.1186/2052-336X-12-65
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/2052-336X-12-65