Abstract
This paper contains the results of a concise statistical review analysis of a large amount of publications regarding the anomalous heat transfer modes of nanofluids. The application of nanofluids as coolants is a novel practise with no established physical foundations explaining the observed anomalous heat transfer. As a consequence, traditional methods of performing a literature review may not be adequate in presenting objectively the results representing the bulk of the available literature. The current literature review analysis aims to resolve the problems faced by researchers in the past by employing an unbiased statistical analysis to present and reveal the current trends and general belief of the scientific community regarding the anomalous heat transfer modes of nanofluids. The thermal performance analysis indicated that statistically there exists a variable enhancement for conduction, convection/mixed heat transfer, pool boiling heat transfer and critical heat flux modes. The most popular proposed mechanisms in the literature to explain heat transfer in nanofluids are revealed, as well as possible trends between nanofluid properties and thermal performance. The review also suggests future experimentation to provide more conclusive answers to the control mechanisms and influential parameters of heat transfer in nanofluids.
Avoid common mistakes on your manuscript.
Introduction
Nanofluids are fluids that contain small volumetric quantities (around 0.0001-10%) of nanosized suspensions of solid particles (100 nm and smaller in size). This kind of fluids exhibit anomalous heat transfer characteristics and their use as advanced coolants along with the benefits over their conventional counterparts (pure fluids or micron-sized suspensions/slurries) is investigated.
Nanofluids were invented by U.S. Choi of the Argonne National Laboratory (ANL) in 1993, during an investigation around new coolants and cooling technologies, as part of the "Advanced Fluids Program" project taking place At (ANL). The term "Nanofluids" was subsequently coined to this kind of colloidal suspensions by Choi in 1995 [1].
Since then, thriving research was undertaken to discover and understand the mechanisms of heat transfer in nanofluids. The knowledge of the physical mechanisms of heat transfer in nanofluids is of vital importance as it will enable the exploitation of their full heat transfer potential.
Several literature review papers were issued by researchers in the last years [2–6]. However, it is the current authors' belief that previous reviewers failed to present all the observations and results obtained from the literature in a clear and understanding method. The main problems arise from the fact that the application of nanofluids as coolants is a novel practise with no established physical foundations explaining the observed anomalous heat transfer characteristics. In addition, due to the recent growth of this area, there are no procedures to follow during testing for the evaluation of the thermal performance. As a consequence, traditional methods of performing a literature review may be inadequate in presenting an unbiased, objective and clear representation of the bulk of the available literature.
It was hence decided to perform a statistical analysis of the findings of the available publications in the literature in order to alleviate the problems faced by previous reviewers. The statistical analysis would enable the depiction of observations on comprehensive charts (histograms and scatter diagrams) hence making possible the extraction of conclusions in a more solid and mathematically trustworthy manner. The present literature review gives the same amount of weight to all of the observations available in the literature.
This review addresses the following questions:
-
a.
What are the general heat transfer characteristics of nanofluids?
-
b.
What are the trends linking the heat transfer performance of certain nanofluids with their by-part mixture parameters?
-
c.
What are the most prevailing theories explaining the anomalous heat transfer behaviour observed in nanofluids?
The next section of this article describes the nanofluid characteristics followed by "Methodology of statistical analysis section". The next two sections present the results of the analysis obtained. "Nanoemulsions" section of this review contains brief information regarding a different type of fluids that has started emerging in the literature recently and might in the future be incorporated into the broader category of nanofluids. The final section contains the main conclusions reached by the current review.
Characteristics of nanofluids
This section epitomizes the most common nanofluid preparation methods by providing information about the last stages of the fluid creation. Note that the "Quality" of a nanofluid represents the extent of achievability of the desired properties of the mixture.
The desired properties of a nanofluid are:
-
a.
Even, durable and stable suspension of the solid nanoparticles in the host fluid (Basefluid)
-
b.
Low or no formation of agglomerates
-
c.
No chemical change of the basefluid (i.e. the solid particles must not chemically react with the host fluid).
Nanofluids follow either single or multi-step creation methods. The single-step creation approach refers to a direct evaporation method (Vacuum Evaporation onto a Running Oil Substrate-VEROS). This method attains the best quality nanofluids; however, there are substantial limitations on the flexibility to create customised nanoparticle volumetric concentrations and basefluid type samples.
The multi-step method provides more flexibility, but, in general, with a penalty in the quality of the attained mixture. Nanofluids can be created either by diluting a very dense solution of the required nanofluid with the matching basefluid or by mixing directly the nanoparticles of choice with the desired basefluid. The first procedure provides more flexibility than the single-step method as the nanoparticles' volumetric concentration can be made to order; however, the quality of the resulting nanofluid is lower than the one achieved via the single-step method.
The second approach of the multi-step method is the most widely used amongst researchers, since it provides maximum flexibility to control the volumetric concentration of the nanoparticles, along with the Basefluid type to be customised given the nanoparticle material, shape and size. On the other hand, this procedure delivered the lowest quality of nanofluids in comparison to all the other methods [1].
The most common liquids used as basefluid are conventional coolants, such as deionised water, engine oil, acetone, ethylene glycol. The most common nanoparticle materials used are aluminium (Al), aluminium oxide (Al2O3), copper (Cu), copper oxide (CuO), gold (Au), silver (Ag), silica dioxide (SiO2), titanium dioxide (TiO2) and carbon nanotubes (CNTs either single-walled, double-walled or multi-walled).
Methodology of statistical analysis
In order to tackle the topics mentioned in "Introduction" section of this paper, the present researchers resolute to following a statistical investigation of a large sample of findings collected from the available literature.
The analysis was performed in three levels. The first level consists of the bulk of the findings from all the published work and enables the demonstration of a general view of the thermal performance of nanofluids. The second level focuses on the most commonly studied nanofluid types and compositions and makes possible to extract trends linking the various nanofluid properties with their thermal performance. The third and final level narrows the sample to include a selection of findings from simple geometry experiments (consisting of travelling hot wire and pipe flow type, instead of complex geometries), ignoring theoretical investigations, thus providing an insight into what appear to be the controlling parameters of thermal performance of nanofluids. Additionally, the final level of analysis reveals what is currently missing from the literature and indicates what aspects need to be investigated further to reach a more conclusive result regarding the links between thermal performance and nanofluid properties.
Findings were gathered regarding the observed enhancement for several heat transfer modes (conduction, convection, pool boiling and critical heat flux) compared to the heat transfer performance of the basefluid alone. Additional information was recorded linking the observed enhancement to the material of the basefluid and nanoparticles, nanofluid composition (nanoparticle concentration), nanoparticle size, temperature of nanofluid, viscosity (enhancement), type of experimental set up, flow status (i.e. laminar or turbulent), possible gravitational effects (e.g. for convective heat transfer), as well as any other interesting observation (see database tables). Finally, the proposed mechanisms for the observed heat transfer anomalies were identified (the assembled database, which was used for the presented review can be found in Tables 1, 2, 3, 4, 5, 6, 7 and 8).
The methodology for the capturing of the findings (numerical and theoretical) from each publication and ensure repeatability of data collection and analysis is as follows:
-
a.
It was decided to limit the data gathering for volumetric concentrations of nanoparticles (F) up to 10% (focus group).
-
b.
Information was presented on diagrams only when adequate number of cases was available in order to be able to approximately describe the shape of the resulting graph.
-
c.
In cases where Dynamic Light Scattering (DLS) or a Brunnauer-Emmet-Teller (BET) sizing method was used in conjunction with a Transfer Electron Microscopy (TEM) or Scanning Electron Microscopy (SEM) method, the latter sizing values were preferred over the former ones as they provide better accuracy (DLS and BET methods both take into account the hydrodynamic size of particles with the assumption of sphericity instead of their actual dimensions. This incurs problems when the nanoparticles are clustered/agglomerated or not spherical).
-
d.
In the cases where the Pool Boiling Heat transfer (PBHT) or Critical Heat Flux (CHF) were considered, values from experiments representing a real and practical engineering application were recorded over the rest.
-
e.
In the rare case where nanoparticle concentrations were represented as mass fraction quantities, a volumetric conversion, according to Equation 1 was used [7].
(1) -
f.
When the mode of heat transfer was not clearly stated or was not evident from the experiment (for example if heat transfer mode was purely via conduction/convection), then the experimental values were sorted into the convection/mixed convection heat transfer class (when both modes are present, it is expected that the effects of convection would prevail over the effects of conduction).
Table 9 displays an average price list of different nanoparticle materials, while Table 10 and Figure 1 show the nanofluid types in the literature. It is evident that the cost of particular type(s) of nanoparticles heavily controlled the available study. As a consequence, the statistical results of this paper are heavily inclined towards indicating the thermal performance of Al2O3-water type nanofluids.
Thermal performance studies
Previous investigators chose to carry out their studies either via the experimental or the analytical route. For the former one, the majority of researchers selected simple experiments (e.g. simple heated pipe/duct flow or stationary flow experiments) using various combinations of nanofluid concentrations and materials under different heat input conditions. The simple experiments provided more insight into the actual physics of heat transfer in nanofluids whilst the more complex experiments usually gave information concerning the practical usage of particular nanofluid compositions and types for certain applications, with little or no referral to the employed theories for heat transfer.
Analytical-computational methods involve the formulation of semi-empirical correlations in order to predict the behaviour of nanofluids. The most common analytical methods are based on the renovated Maxwellian [8], Equation 2, or renovated Hamiltonian-Crosser equation models [9], Equation 3, to be able to predict the effective heat conduction in a nanofluid. Additional components are usually added to the equations to take into account the Brownian motion heat transfer mechanism.
Equations 2 and 3 rely on the molecular layering theory, i.e. the presence of nanolayers with reduced thermal resistance covering the surface of each nanoparticle. The renovated Hamiltonian-Crosser model equation is assumed to be more accurate, as the shape of the solid nanoparticles is taken into account (sphericity), while the renovated Maxwellian model only assumes spherical particles and works well for nanoparticle diameters that are less than 10 nm [8].
For the other heat transfer modes (apart of heat conduction), the formulation of further equations to include additional parameters (e.g. density changes, buoyancy forces, gravitational forces, etc.), has its foundations on Equations 2 and 3.
The critical issue with numerical simulations and semi-empirical correlations is that the majority of researchers predetermined, to some degree, the physical mechanisms underlying behind the anomalous heat transfer characteristics in nanofluids. For example, some semi-empirical correlations are based on fitting experimental measurements determined for specific applications. As a result, with the physical understanding of the heat transfer mode mechanisms yet unknown, it becomes trivial to solemnly rely on such simulations and equations to hold valid for a general range of nanofluid compositions, types and application (e.g. as coolants in various heat exchanger designs).
Heat transfer characteristics [1–128]
In the following section, the heat transfer characteristics of nanofluids are considered. Information was collected from the literature and processed to reveal the thermal performance of nanofluids for different heat transfer modes (purely conductive, convective/mixed, pool boiling and CHF). Information, regarding the mechanisms that various researchers employed to describe the anomalous heat transfer, was also collected to allow the evaluation of the most statistically occurring patterns for each heat transfer mode.
Finally, a cross-correlation of the findings between the different levels of analysis (explained in "Methodology of statistical analysis" section) was also considered to evaluate the observations and reveal any possible trends linking the thermal performance characteristics of nanofluids with their by part properties (i.e. consistency and application). Furthermore, the focused samples of level 3 of the analysis provided further information about the parameters controlling the thermal performance characteristics of nanofluids.
General observations: level 1 analysis
Level 1 of the analysis considers the entire sample record collected from the literature. It aims to present a general idea of the thermal performance of nanofluids for different heat transfer modes.
Heat transfer characteristics
a. Heat transfer enhancement studies purely via conduction (130 observations)
Strong evidence of thermal conductivity enhancement exists, as indicated by the histogram of the findings of Figure 2. An enhancement lying between 5 and 9% was observed for 30% of the sample. The variation around the 5-9% enhancement range is large. However, the majority of the remaining observations are in the 1-4% and 10-24% enhancement ranges, representing around 45% of the sample. The remaining data (around 25% of the sample) indicate enhancement above 29% and some even larger than 84%. Therefore, there is a need for additional understanding of the origin of the resulting enhancement of heat transfer due to conduction.
b. Heat transfer enhancement studies via convection/mixed heat transfer mode (91 observations)
Strong evidence of heat transfer enhancement by nanofluids for convective or mixed heat transfer mode is indicated in the histogram of Figure 3. Most data indicate a convective heat transfer coefficient enhancement between 10 and 19% (18% of the sample). However, the spread of the enhancement results is very large. The majority of the results (around 45% of the sample) indicated unspecified enhancement. There is also weak statistical indication of nanofluids causing deterioration of the heat transfer coefficient (11% of the sample) and an even smaller percentage of the sample indicating no enhancement at all (3% of the sample). Therefore, the statistical analysis for convective heat transfer is less consistent than for conduction, which supports the need for more research.
c. PBHT enhancement studies (22 observations)
Strong evidence of enhancement of heat transfer due to pool boiling is indicated in the histogram of Figure 4. Most data reporting specific values show an improvement of the PBHT coefficient between 40 and 44% (9% of the sample). However, the majority of the results (45% of the sample) indicate an unspecified enhancement, while there is an indication of deterioration with moderate statistical importance (23% of the sample) and a weak statistical percentage of the considered sample indicating no enhancement at all (5% of the sample). However, the number of publications for PBHT is low and, as a consequence, the findings have lower confidence level. In addition, the complexity of the physics of PBHT can cause large variation in the observed enhancement and the lack of understanding does not allow the assessment of optimised operation with PBHT.
d. CHF enhancement studies (23 observations)
Strong evidence of enhancement of CHF in boiling applications is indicated in the histogram of Figure 5. Most observations show an improvement of the CHF coefficient lying between 100 and 200% (35% of the sample). There is a weak statistical percentage of the considered population indicating deterioration (4% of the sample). However, the spread of the results is large and the confidence level of the findings is low. Since several publications have reported very large enhancement of CHT, it is important to understand the origin of CHT enhancement in nanofluids.
e. Proposed physical mechanisms for the anomalies of heat transfer
An outline of all the proposed mechanisms for each type of heat transfer study is presented. These mechanisms (or a combination of more than one mechanism) are used by researchers in the literature to explain the augmentation of the heat transfer coefficient in nanofluids. The proposed mechanisms are briefly explained first before the findings of the statistical analysis are presented. The findings are considered jointly for conduction and convection and for pool boiling and CHF.
Conduction/convection/mixed mode heat transfer studies (85 observations)
The proposed mechanisms for the enhancement of heat transfer in conduction, convection or for mixed conditions in the literature are described below. Example references of papers containing the explanation of the theory are also provided.
Brownian motion
Many researchers believe that there is an apparent enhancement of heat transfer due to Brownian motion of nanoparticles. Their speculations rely on the fact that nanoparticles provide larger surface area for molecular collisions. The higher momentum of nanoparticles (higher mass concentrations compared to the host fluid molecules) are believed to carry and transfer thermal energy more efficiently at greater distances inside the basefluid before they release it in a colder region of the fluid (small packets of energy) [42].
Interfacial layer theory (Kapitza resistance)
The Kapitza resistance is a thermal boundary resistance arising from thermal energy carrier scattering at an interface (scattering of phonons and electrons). The type of carrier scattered will depend on the materials governing the interfaces. In liquid-solid interfaces (e.g. nanoparticle-base fluid interfaces), the boundary resistance is believed to decrease hence the overall thermal resistance of the system (e.g. a nanofluid in this case) is believed to reduce [70].
Aggregation and diffusion
This mechanism suggests that there is a formation of a linear assembly of nanoparticle chains upon their suspension in the host fluid. The occurrence of this chain assembly is speculated to provide a faster path for heat transfer through the nanofluid (faster heat diffusion) [65].
Electrical double layer (EDL) theory
This mechanism proposes an alteration of the strength of intermolecular interaction forces that in effect change the mean free path of the nanoparticles and hence augmenting the heat transfer of molecules [48].
Flattening of velocity profile due to viscosity
This mechanism proposes that the viscosity change of nanofluids leads to a more uniform velocity profile for flows in pipes and ducts than the expected parabolic velocity profile (Poiseuille flow). The increased near wall velocity is believed to provide an increase in the convective heat transfer coefficient observed in these applications [106].
Near field radiation
Some researchers believe that there is infrared radiation emission and absorption augmentation at the nanoscales (near field radiation). This enhances heat transfer between the heating surface and the nanoparticles, the basefluid molecules and the nanoparticles and between the nanoparticles themselves by a factor of 2-3 compared to the far field radiation estimates [37].
Thermophoretic forces
Thermophoretic forces on nanoparticles arise from the presence of temperature gradients in the fluid causing the concentration of nanoparticles to change around heating and cooling sides relative to the mean value. The consequence of this nanoparticle redistribution is the alteration of the heat transfer coefficient accordingly [121].
Shear thinning behaviour of flows
Some researchers believe that nanofluids exhibit non-Newtonian characteristics with shear thinning behaviour. The viscosity is believed to reduce at the solid boundaries of a flowing nanofluid, because the shear rate of the nanofluids increases along the walls. This promotes increased heat transfer between the wall and the liquid because the thermal boundary layer width is reduced. It also provides a beneficial lubrication effect [30].
Phonon transfer
A few researchers suggested that nanofluids have an increased heat transfer rate due to specialised phonon and electron interaction and scattering at the nanoscales (ballistic heat transport) [64].
Thermal conductivity enhancement alone
Some researchers have accounted for the increase of the thermal conductivity alone (without providing more information) to account for the observed enhancement of heat transfer [40].
Figure 6 presents the histogram of the proposed mechanisms to explain the anomalous heat transfer for conduction, convection and mixed cases in the literature. The observations from Figure 6 are summarised below and there are three most commonly proposed mechanisms:
-
a.
Brownian motion (33% of the sample)
-
b.
Interfacial layer theory (Kapitza resistance) (22.4% of the sample)
-
c.
A combination of the Brownian motion and the aggregation and diffusion theories (11% of the sample).
PBHT and CHF enhancement studies (40 observations)
The proposed mechanisms for the enhancement of PBHT and CHF in the literature are described below.
Deposition of nanoparticles on heating surface
The vast majority of researchers assume that, for this heat transfer mode, the use of nanofluids leads to a modification of the heating surface. The alteration promotes higher frequency of bubble departure with smaller bubble size. At the same time, there is an increased wettability that inhibits the dry patch development on the heating element, leading to increased CHF [57].
Passive/active mode of heat transfer
The passive mode mechanism suggests that nanoparticles provide additional nucleation sides for vapour bubble formation and boiling. The active mode mechanism suggests that nanoparticles provide appropriate surface area for converting infrared Radiation into heat. These two modes are suspected to increase the overall heat transfer coefficient of nanofluids [115].
Long range structural disjoining pressure
Confinement of nanoparticles in the meniscus area, supplying liquid to the formation of the vapour bubble at the dry patch, is believed to promote an increased wettability and inhibition of the dry patch development [119]. This leads to increased CHF.
Electrical double layer (EDL) theory
This mechanism was also proposed to explain conduction/convection heat transfer enhancement. It is based on a change of the strength of intermolecular interaction forces that modifies the mean free path of the nanoparticles [48].
Thermal conductivity enhancement alone
This mechanism was also proposed to explain conduction/convection heat transfer enhancement. It makes use of the increase of the thermal conductivity alone (without providing more information) to account for the observed enhancement of heat transfer [40].
Figure 7 presents the histogram of the proposed mechanisms to explain the anomalous heat transfer for pool boiling and CHF in the literature. The observations from Figure 7 are summarised below and there are two most commonly proposed mechanisms:
-
a.
Alteration of the heating surface due to the deposition of nanoparticles (75% of the sample)
-
b.
Passive/active heat transfer mode theory (10% of the sample)
In summary, a general overview of the thermal performance for each heat transfer mode was presented. It is evident that the vast majority of publications in the literature indicated that nanoparticles are found to augment the heat transfer coefficient of a given basefluid for every mode of heat transfer.
The most popular mechanisms for explaining the anomalous heat transfer were also presented. All of the proposed mechanisms have not been verified experimentally and as a result these proposals still remain notions of what is theoretically employed by researchers to explain the phenomena.
Evaluation of trends of specific nanofluids: level 2 analysis
Level 2 of the statistical analysis contains a narrowed down sample of publications. The criterion for selecting the publications of the secondary group of level 2 was the nanofluid material composition. It was decided to select the nanofluid material consistencies that were most commonly used in the literature. This enables the in-depth comparison between observations recorded from different research groups found in the literature, hence allowing the definition of possible trends linking the thermal performance characteristics of nanofluids with their by part properties (such as consistency, temperature of nanofluid, etc). The formation of the secondary group also provides correlation information between the two analysis levels (namely levels 1 and 2) that assists the evaluation of the statistical analysis findings.
Nanofluid types considered (249 observations)
A histogram of nanofluid types employed in the literature was presented in Figure 1 and was considered again here to discover which types have been studied most and, hence, allow the creation of secondary focus groups. The selected sample was narrowed to the following nanofluids: Al2O3-water, Al2O3-ethylene glycol (EG), CuO-water and TiO3-water (see Table 10). The processing of the above level 2 analysis sample indicated that the number of publications for the latter two types of nanofluids was too small to obtain conclusions with reasonable statistical significance. Hence, it was decided to consider only the results for the former two nanofluids (i.e. the Al2O3-water and Al2O3-EG).
Heat transfer characteristics
The statistical analysis 2 of the thermal performance was performed for each heat transfer mode, when the sample was large enough (above 10 observations) to justify the statistical findings. Histograms of this analysis are not presented here, but the findings are summarised below.
a. Heat transfer enhancement via conduction
Al 2 O 3 -water nanofluids (41 observations)
Strong evidence of thermal conductivity enhancement is present. Heat transfer enhancement was observed mainly between 5 and 9% (34% of the sample). The variation around the 5-9% enhancement regime was small with the majority of the remaining observations in the enhancement range of 10-14% (32% of the sample).
Al 2 O 3 -EG nanofluids (11 observations)
Strong evidence of thermal conductivity enhancement is present. Heat transfer enhancement lying between 5 and 9% was similarly observed (36% of the sample). The variation around the 5-9% enhancement range was again small with the majority of the remaining observations in the 10-14% range (27% of the sample).
The findings for the two nanofluids are complimentary and in agreement with the findings for all types of nanofluids as obtained from the analysis of level 1 and presented in Figure 2.
b. Heat transfer enhancement studies via convection/mixed heat transfer mode (91 observations)
Al 2 O 3 -water nanofluids (36 observations)
There is strong evidence of heat transfer enhancement with most publications indicating an unspecified value of enhancement (39% of the sample).
Al 2 O 3 -EG nanofluids (11 observations)
Strong evidence of heat transfer enhancement is present. Most observations indicate an enhancement between 1-4% and 10-14% (27% of the sample for each range). The spread is small with all results indicating an enhancement around the 1-19% enhancement range.
It should be noted that the findings for the two nanofluids is in agreement with the findings of analysis level 1, as presented in Figure 3.
Proposed physical mechanism for anomalous heat transfer
a. Conduction/convection/mixed mode heat transfer studies
Al 2 O 3 -water nanofluids (29 observations)
-
a.
Brownian motion (28% of the sample)
-
b.
Brownian motion combined with the aggregation and diffusion theory (28% of the sample)
-
c.
Interfacial layer theory (Kapitza resistance) (17% of the sample)
Al 2 O 3 -EG nanofluids (13 observations)
-
a.
Brownian motion (85% of the sample)
-
b.
Interfacial layer theory (Kapitza resistance) (15% of the sample).
The most popular proposed mechanism is the Brownian motion of the nanoparticles. This is in agreement with the findings of level 1 analysis presented in Figure 6. Some differences exist for the second and third most popular mechanisms, but both are the same as for the level 1 analysis.
b. PBHT and CHF (12 observations)
The sample for the Al2O3-EG nanofluids was too small to give a credible statistical result. Hence, only the Al2O3-water nanofluid sample is presented. The most popular proposed mechanisms are:
-
a.
Alteration of the heating surface due to deposition of nanoparticles (83.3% of the sample)
-
b.
Brownian motion combined with the alteration of the heating surface due to deposition of nanoparticles (8.33% of the sample)
-
c.
Deposition and aggregation theory combined with the diffusion and thermal conductivity (alone) (8.33% of the sample).
The alteration of the heating surface by the deposition of nanoparticles is the most popular proposed mechanism for the explanation of enhanced PBHT and CHF. This is in agreement with the findings of Level 1 analysis presented in Figure 7.
Scatter diagrams based on level 2 analysis: indication of trends
Level 2 analysis allowed the formation of various scatter diagrams and two of the most representative diagrams are selected and can be seen in Figures 8 and 9. Figure 8 presents the effect of nanoparticle concentration and size on conducting heat transfer for Al2O3-water nanofluids. Figure 9 shows the effect of nanoparticle concentration and size on the viscosity of the mixture for Al2O3-water nanofluids. The scatter diagram analysis provided vital information on the links between nanofluids parameters and their thermal performance. The following trends were derived:
-
a.
The level of enhancement for the purely conductive case indicated an increasing trend with increasing nanofluid temperature and nanoparticle concentration, while there is a slight hint of the enhancement increasing with nanoparticle size (see Figure 8).
-
b.
The effective viscosity of the mixture is enhanced and the findings show an increasing trend with decreasing fluid temperature, increasing volumetric concentration. There is also a slight hint of an effective viscosity increase with decreasing nanoparticle size (see Figure 9).
-
c.
The level of enhancement for the convection/mixed heat transfer mode indicated an increasing trend with increasing temperature, volumetric concentration and decreasing nanoparticle size.
Unfortunately, this trend can only be deduced by taking account the entire sample of scatter diagrams produced hence there is not a single representative diagram to display supporting it (contrary to the conductive and viscosity enhancement trends considered).
The trends appear to hold true up to the level where the nanofluid defining qualities (regarding particle suspension and chemical consistency properties as listed in Characteristics of nanofluids section) are still satisfied and the nanoparticle concentrations remain in between the boundaries set in the methodology of observation collection (0.0001-10 vol.%). It should be noted that the observed trends cannot be quantified to evaluate the contribution of each by part property of the nanofluids. The observed trends will be discussed in the next subsection.
Unfortunately, the sample size was not large enough to extract trends regarding PBHT and CHF. Moreover, due to sample size limitation it was also impossible to determine nanoparticle material effects on thermal performance characteristics.
Discussion of findings from level 2 analysis
The thermal performance assessment study of the second level agrees to a large degree with the findings of the first level. The cross correlation between the two levels ensures that the narrowed sample still falls into the reliability limits of the study.
The heat transfer enhancement studies for the Al2O3-water/EG generally indicated strong enhancement for the conduction and convection/mixed modes. More specifically, for the conduction heat transfer enhancement, the two nanofluids performed the same. For the convection/mixed heat transfer mode, the results for the two nanofluids do not correlate to the same level of enhancement.
For the statistically most popular proposed mechanism to explain the anomalous heat transfer. Both types of nanofluids agree on the Brownian motion of nanoparticles being most popular mechanism to explain the phenomena while small deviations appear regarding the secondary and third most popular mechanisms.
In the light of this evidence, it can be concluded that the narrowing of the sample to perform the second level of the analysis can still be accounted creditable, as it generally agrees with the findings from the overall sample of level 1. The findings regarding the thermal performance indicate that the basefluid material has little influence on the heat transfer enhancement in the conduction mode. On the contrary, the basefluid material seems to affect the performance for the convection/mixed heat transfer mode as discrepancies on the performance studies for the two materials were observed.
The observed trends on the effect of nanofluid properties to heat transfer of the trend formation can be accounted to the following for each subsection:
Trends for conduction enhancement
The findings indicate that conduction enhancement increases with increasing particle size, increasing nanoparticle concentration and mixture temperature. For this "less active" (compared to the convection/mixed) mode, Brownian motion becomes less pronounced; it appears that this trend is reasonable by referring partially to the second most popular mechanism found in the literature, namely aggregation and diffusion. By increasing the nanoparticle size and concentration, the highly conductive nanoparticles can diffuse the heat faster into the liquid as the thermal energy coefficient for solids is much larger than that of liquids. The increase of particle size provides longer and more effective ground for heat diffusion through each nanoparticle, while the increase of concentration increases the volume of the highly conductive solid available for heat transfer in the nanofluid. The enhancement increases with increasing temperature. This is accounted for by conventional heat transfer mechanisms. The increased temperature leads to statistically more energetic molecules. The statistical thermo mechanics for liquids and solids dictates that the intermolecular interactions will increase (collisions become more frequent and the energy involved per collision increases due to the average molecular speed augmentation). As a consequence, the heat transfer due to conduction is enhanced with increasing temperature. It should be noted that there must be a critical value of nanoparticle size and concentration beyond which the observed trend will reverse. However, there is no information available that will be able to demonstrate this assessment.
Trends for convection/mixed enhancement
The convection/mixed heat tramsfer mode is more "energetic" than conduction. Hence, Brownian motion of nanoparticles is more pronounced. The liquid molecules are allowed to move under the influence of buoyant forces arising from density variations inside the liquid. The heat transfer enhancement follows an increasing trend with decreasing nanoparticle size, increasing nanoparticle concentration and increasing temperature. For the latter, the same principle holds true as for conduction enhancement. For the former, at a given volumetric concentration of nanoparticles, the decrease in nanoparticle size results in an increase in the particle surface area available for collisions and at the same time an increase in the number of nanoparticles and a decrease in the corresponding mass per particle in a given volume of a nanofluid (the mass reduction per particle is much smaller compared to the gain of free surface area available for collisions). The increased surface area and number of nanoparticles results into an increased number of collisions between the basefluid molecules and the nanoparticles as well as between the nanoparticles themselves. Moreover, the decreased particle mass and increased collision count and hence overall collision energy involved leads to an increase of the mean free path (according to the most prevailing mechanism found in the literature) and energy content per nanoparticle. Brownian motion is hence augmented giving rise to large local density variations (and hence large buoyancy force variations) that, in turn, provide an enhancement in the convective/mixed heat transfer coefficient.
Trends for effective viscosity of nanofluid mixture
The effective viscosity follows an increasing trend with decreasing nanoparticle size, increasing nanoparticle concentration and decreasing temperature. For the latter, the decrease of temperature results in less energetic i.e. more sluggish liquid molecules. The decreasing temperature results in a decreasing kinetic energy of each molecule. The attractive/repulsive intermolecular forces become more pronounced giving rise to an enhancement in viscosity. Additionally, the decrease in particle size for a given volumetric concentration and volumetric amount of a nanofluid results in larger nanoparticle surface area and number count, which consequently results in a rise in the shear stress observed between the solid-solid and solid-liquid interfaces inside the fluid-contrary to the shear thinning mechanism accounted by some researchers. This effect is also augmented by increasing the volumetric concentration of nanoparticles, since the overall nanoparticle surface area and number count of nanoparticles are increased as well.
Focus on simple experiments: level 3 analysis
It was decided to investigate further the available information by considering publications, which reported simple and well-documented experiments. The simplicity of the experiments will allow focusing on the effects of nanoparticles, while other parameters introduced by the complexity (e.g. geometry) of the experiment will be eliminated. It is expected that these publications will enable a more generic view of the anomalous heat transfer characteristics of nanofluids, while it will also allow other researchers to reconstruct experiments in order to carry out further investigations on the notions and suggestions of previous studies.
It was decided to focus on publications that:
-
a.
include a physical experiment (i.e. eliminate those with computer simulations)
-
b.
consider simple experiments, where concise documentation is available, consisting of:
? heat exchange via flow through a duct/pipe (simple pipe flow)
? heat exchange in stationary flow, i.e. transient hot-wire experiments
It was hence possible to construct new limited data sets and produce new histograms that enable the extraction of more targeted quantities. Results are presented where the sample size was sufficient to have a statistical importance (at least 10 observations).
Transient hot-wire experiments
The transient hot-wire experiments involve conventional conductivity measurements in a stationary fluid by means of the transient hot-wire apparatus and method. This experimental procedure is considered to be one of the most accurate and simple methods used to deduce the thermal conductivity of nanofluids. The experiments are believed to provide an insight in the performance criteria without unnecessary experimental complexities that might affect the results acquired. Heat transfer studies and analysis to determine the proposed mechanisms for heat transfer were performed similarly to level 1 and level 2 of this investigation. No histograms are presented; however, the numerical results are tabulated in the subsections following.
a. Heat transfer results
Heat transfer enhancement purely via conduction (17 observations)
There is strong indication that nanoparticles can enhance the heat transfer via conduction. All observations indicated an enhancement. Statistically, most observations indicate an enhancement in the range of 10-14% (41% of the sample) with a moderate spread. The performance indication is different to the 5-9% most occurring enhancement regime indicated by level 1 but overall lies in the 1-24% general enhancement regime also indicated by level 1.
CHF enhancement (13 observations)
All observations indicate an enhancement. Most observations show statistically an improvement of the CHF coefficient in the range of 100-200% (46% of the sample). This figure agrees with the performance value of the same heat transfer mode observed in level 1.
b. Proposed mechanisms for heat transfer anomalies
Conduction/convection/mixed mode heat transfer (16 samples)
The statistics indicate that a large percentage of researchers explain the heat transfer enhancement by the interfacial layer theory and the Brownian motion theory in combination with the thermophoretic effect on nanoparticles (37.5% of the sample for each category). The Brownian motion theory comes third most popular (25% of the sample). Differences are found compared to the findings of the 1st level of analysis concerning the most occurring proposed mechanism for heat transfer anomalies.
PBHT and CHF enhancement (17 observations)
The analysis indicates that the majority of researchers (82.4%) account for the heat transfer enhancement through the alteration of the heating surface due to deposition of nanoparticles. The second proposed mechanism is the aggregation and diffusion in combination with the thermal conductivity enhancement alone theories (11.8% of the sample). The third most favoured mechanism refers to the electrical double layer (EDL) in combination with the aggregation and diffusion and the alteration of the heating surface due to the deposition of nanoparticles theories (5.9% of the sample). The most probable mechanism agrees with the findings of the first level however, the second and third most probable mechanisms do not agree with the first analysis level.
Simple pipe flow experiments
To investigate the convection/mixed heat transfer mode it was decided to narrow the sample to the experiments involving flow in a heated pipe. Temperature measurements are made and in conjunction with the already established physics governing flow in heated pipes it is possible to extract convective heat transfer performance data. This kind of experiments represents the simplest experimental arrangements around the convective mode performance assessment found in the literature. The outline of the section is similar to the analysis performed for the transient hot-wire experiments. No histograms are present but instead the results are presented in their numerical form.
a. Heat transfer results
Heat transfer enhancement via conduction (19 observations)
There is strong indication that nanofluids can enhance the conductive heat transfer mode. All observations indicated an enhancement. Most observations indicate a heat transfer enhancement in the range 5-9% (42% of the sample). This performance value agrees with the one found in analysis level 1.
Heat transfer enhancement via convection/mixed heat transfer mode (28 observations)
The majority of the publications shows heat transfer enhancement in the range of 10-14% (14% of the sample). However, the spread of the enhancement results is large. There is also moderate statistical evidence that the addition of nanoparticles does not change the thermal performance of the heat transfer via convection/mixed mode (36% of the sample). The findings agree partially with the ones found in level 1 (level 1 produced a probable enhancement of 10-19%).
b. Rheological studies (23 observations)
There is strong indication that nanoparticles enhance the effective viscosity of the considered nanofluids (78% of the sample indicates an increase). Most publications have on average a viscosity enhancement between 5 and 14% (34% of the sample) and moderate evidence showing that the addition of nanoparticles has no effect on the effective viscosity of nanofluids (22% of the sample). The rheological studies of this section contain the vast majority of experiments of this kind in the entire observation sample hence a comparison with level 1 cannot be performed.
c. Proposed mechanisms for the heat transfer anomalies
Conduction/convection/mixed mode heat transfer studies (13 observations)
The statistics indicate that the majority of researchers explain the enhancement of heat transfer through the Brownian motion of nanoparticles in combination with the aggregation and diffusion theory (53.8% of the sample), followed by the second most statistically occurring, which is the Brownian motion theory alone (30.8% of the sample). Therefore, the majority of the researchers believe that the Brownian motion is the main mechanism and this is in agreement with the results of level 1.
Discussion of findings from level 3 analysis
The thermal performance analysis of the narrowed down sample agreed moderately well with the analysis performed in level 2 and the entire population of observations analysed in level 1.
Specifically, for the transient hot-wire experiments, the conduction mode enhancement was found to lie close to the arithmetical values found in level 1 and level 2, while, for CHF, the enhancement was also found in agreement with the previous two levels of analysis. For conduction/convection/mixed heat transfer, the most popular proposed mechanisms are in relatively good agreement with those of level 1 and level 2 (the two most probable mechanisms are followed by a third-the thermophoretic effect theory). The deposition of nanoparticles on the heating surface was identified as the most popular mechanism in explaining the heat transfer anomalies for PBHT and CHF, which is also in good agreement with the findings of level 1 and level 2 analyses.
For the simple pipe flow experiments, the heat transfer enhancement via pure conduction and convection/mixed modes were in good agreement with those of level 1 and level 2 analyses. The most popular mechanism to explain the observations was the Augmented Brownian motion in combination with the aggregation and diffusion mechanism, which again are in good agreement with the results of the level 1 and level 2 analyses.
Apart from the examination of the heat transfer performance, the current authors examined the correlation between several controlling parameters and nanofluid thermal performance in order to investigate if the trends were the same as those of level 2 analysis. The five parameters under investigation were the nanofluid type (basefluid and nanoparticle materials), the nanoparticle size and concentration along with the flow type (stationary/turbulent/laminar flow) and nanofluid temperature. The analysis yielded no correlation between the parameters associated with this sample even though the sample size appears arithmetically sufficient.
The reason for the absence of any correlation between the observations and their by part properties was further investigated. It was discovered that the combination of the different parameters resulted in a variety of different experimental conditions, thus any comparison of any individual parametric effect was impossible as the sample became too small to study. At the same time, it was possible to indirectly deduce that the investigated five parameters play an important role in the emerging thermal performance of nanofluids. Finally, the 3rd level of analysis pointed out that despite the large sample of collected publications for this literature review (more than 250), no study was performed to take into account simultaneously all five parameters and their effects on the thermal performance of nanofluids.
Nanoemulsions
Nanoemulsions are a new type of fluids that bear similarities with nanofluids. They emerged recently in the literature and have been attracting attention from the research community. Nanoemulsions usually comprise of an insoluble mixture of droplets with a single or a soluble mixture of fluid(s) as the base/carrier fluid, i.e. fluid-in-fluid mixtures. This is in contrast to the broader definition of the two phase nature of nanofluids (solids-in-fluid mixtures). The most common formation of nanoemulsions arises from a stable suspension of droplets of one of the main constituents into the other(s) at various concentrations where the stability of the emulsion is still ensured.
The droplets have sizes of the nanoscale order and their stability is ensured by means of surfactants (contrary to nanofluids where the stability can also be ensured without the need of a surfactant). This kind of fluids exhibited heat transfer augmentation effects in conduction studies. Thermal enhancement up to 52% was reported upon testing a nanoemulsion mixture of water-in-FC72 oil [129], while experimentation with nanoemulsions of oil in a binary mixture of H2O/LiBr [130] and water in n-decane [131] indicate augmentations of 3.6% and very little augmentation to suggest any heat transfer potentials, respectively.
One of the most appealing aspects of nanoemulsions is that they can be mass produced using cheap emulsification techniques and the emulsion can hold the carrier fluid's electrical properties while the suspension stability (under specific conditions) can be larger compared to their conventional two phase nanofluid counterparts. One of their major drawbacks is that the heavy use of surfactants to achieve mixture stability leads to hysteresis phenomena in the thermal performance of these fluids. An additional issue-this time to be foreseen from the literature review analysis on nanofluids-is that the stability of the nanoemulsion is probably going to be endangered in high temperature heat transfer as the conventional surfactant chemical composition at those temperatures changes irreversibly (surfactants are destroyed).
All in all, the area of thermal nanoemulsion performance is rather immature to reach to conclusions regarding the thermal performance of such fluids, since not enough experiments have been performed up to date to quantify creditable statistics.
Summary and future research needs
A literature review was performed, which statistically analysed a large amount of literature regarding the anomalous heat transfer modes exhibited by nanofluids. Three levels of analysis were selected. The first one allowed the extraction of results concerning general heat transfer characteristics and performance of nanofluids. The second one focused on revealing any possible trends linking the heat transfer performance of certain nanofluids with their by part parameters. The third level revealed the parameters that appear to control the thermal performance of nanofluids and indirectly indicated the current research needs to enable reaching a more conclusive result.
All three levels of analysis agreed to a large degree on the choice of proposed mechanisms to explain the anomalous heat transfer, as well as on the thermal performance of nanofluids for different heat transfer modes. This indicates that both diminished sample sets of level 2 and level 3, created from the bulk population of publications, were reliable to proceed with the extraction of statistical results.
The statistical analysis of thermal performance indicated that there is a notable enhancement for conduction, convection/mixed, pool boiling and CHF heat transfer modes. The level of enhancement varies for each sub set with the purely conductive mode showing the least enhancement (around 5-9% most frequently observed), the convection/mixed mode a moderate enhancement (around 10-14%), the pool boiling mode a higher enhancement of 40-44%, while the CHF demonstrated the highest enhancement (100-200%). For some of the considered heat transfer modes, heat transfer coefficient deterioration or no effect were also recorded; however, these occurrences were low.
For the explanation of the enhancement related to conduction, convention/mixed heat transfer modes, the most popular theories revolve around either the Brownian motion of nanoparticles, the interfacial liquid layering (Kapitza resistance) theory, the aggregation and diffusion theory or simply a combination of all three.
For PBHT and the CHF, the most commonly proposed mechanisms are the alteration of the heating surface by deposition of nanoparticles along with the passive/active mode theories.
The sample set of the level 2 analysis indicated that for the purely conductive mode, the basefluid material has negligible effect to the enhancement of heat transfer. It was also possible to define trends, linking properties of nanofluids with their thermal performance as follows:
-
The level of enhancement for the purely conductive case indicated an increasing trend with increasing nanofluid temperature and nanoparticle concentration, while there is a slight hint of enhancement with increasing nanoparticle size.
-
The level of enhancement for the convection/mixed heat transfer mode indicated an increasing trend with increasing temperature, volumetric concentration and decreasing nanoparticle size.
-
The effective viscosity of nanofluids increases with decreasing temperature of the fluid and increasing volumetric concentration. There is also a slight hint of the effective viscosity increase with decreasing nanoparticle size.
The trends remain valid up to the degree where the nanofluid defining qualities (regarding particle suspension and chemical consistency properties as listed in "Characteristics of nanofluids" section) are still satisfied and the nanoparticle concentrations remain in between the boundaries set in the methodology of observation collection (0.0001-10 vol.%). The most popular mechanisms proposed in the literature to explain the heat transfer anomalies observed supported the trend behaviour observed.
Based on the findings of the statistical analysis of the literature, some recommendations for future research are provided below.
-
(a)
The final level of analysis, level 3, outlined the five apparent parameters controlling thermal performance. Those are the nanofluid type (Basefluid and nanoparticle materials), the nanoparticle size and concentration, the flow type (stationary/turbulent/laminar flow) and lastly the nanofluid temperature. Level 3 analysis indicated that no parametric study has been performed that takes into account all five parameters noted above to evaluate their contribution on the thermal performance of nanofluids.
-
(b)
The review demonstrated that, even though attempts were frequently made to ensure that the quality criteria of the prepared nanofluids were satisfied prior the experiments, no attempt has been presented to re-examine the nanofluids after or during experiments-with the exceptions of some cases of pool boiling or CHF investigations or microchannel clogging investigations due to nanofluids. As a result, it is doubtful whether the nanofluid properties (e.g. nanoparticle size) remain the same during or after experiments.
-
(c)
No study has been performed to quantify any corrosion effects during long term operation of nanofluids heat/cooling circuits.
-
(d)
The mechanism responsible for the observed heat transfer enhancement has not been verified experimentally. This is an important step for the optimisation of the performance of nanofluids and the development of appropriate computational models to describe their behaviour.
-
(e)
A larger amount of experimental studies are related to conduction and less is available for convection, pool boiling and CHF modes. Therefore, more emphasis should be given to these modes of heat transfer in future experimentation.
Finally, a brief consideration of a new type of fluid that bears similarities to nanofluids and might in the future be part of the broader nanofluid category has been examined. nanoemulsions are single-phase liquid-into-liquid mixtures that can potentially be of interest due to their abnormal thermal performance. Unfortunately, not enough experiments have been performed to allow statistical analysis of their performance.
Abbreviations
- BET:
-
Brunnauer-Emmet-Teller
- CNT:
-
carbon nanotube
- CHF:
-
critical heat flux
- DLS:
-
dynamic light scattering
- EDL:
-
electrical double layer
- EG:
-
ethylene glycol
- HT:
-
heat transfer
- NF:
-
nanofluids
- PBHT:
-
pool boiling heat transfer
- SEM:
-
scanning electron microscopy
- TEM:
-
transfer electron microscopy.
- A:
-
= when ellipsoid is defined by
a, b and c are constants indicating the points where the ellipsoid is crossing the x, y and z-axis, respectively
- CHF:
-
Critical Heat Flux
- f :
-
volume concentration of the solid ellipsoids without surrounding layers; fe= r vf
- HT:
-
Heat transfer
- K:
-
heat transfer coefficient
- kpe:
-
equivalent thermal conductivity of equivalent Nanoparticle
- kpj:
-
equivalent thermal conductivities along the axes of the complex ellipsoid
- NF:
-
Nanofluids
- PBHT:
-
Pool Boiling Heat Transfer
- rv:
-
volume ratio of nanolayer to nanoparticle
- BF:
-
Basefluid (host fluid)
- eff:
-
Effective
- f:
-
Fluid
- NF:
-
Nanofluid
- NP:
-
Nanoparticle
- p:
-
Solid particle
- ?:
-
density
- F:
-
volumetric concentration
- Fm:
-
mass concentration
- ?:
-
sphericity
References
Sarit K, Das SUSC, Wenhua Yu, Pradeep T: Nanofluids: Science and Technology. 1st edition. Hoboken, NJ: John Wiley & Sons, Inc; 2007.
Kakaç S, Pramuanjaroenkij A: Review of convective heat transfer enhancement with nanofluids. Int J Heat Mass Transfer 2009, 52: 3187–3196. 10.1016/j.ijheatmasstransfer.2009.02.006
Taylor Ra, Phelan PE: Pool boiling of nanofluids: comprehensive review of existing data and limited new data. Int J Heat Mass Transfer 2009, 52: 5339–5347. 10.1016/j.ijheatmasstransfer.2009.06.040
Wang XQ, Mujumdar AS: Heat transfer characteristics of nanofluids: a review. J Therm Sci 2007, 46: 1–19. 10.1016/j.ijthermalsci.2006.06.010
Wen D, Lin G, Vafaei S, Zhang K: Review of nanofluids for heat transfer applications. Particuology 2009, 7: 141–150. 10.1016/j.partic.2009.01.007
Trisaksri V, Wongwises S: Critical review of heat transfer characteristics of nanofluids. Renew Sustain Energy Rev 2007, 11: 512–523. 10.1016/j.rser.2005.01.010
Bang I, Heungchang S: Boiling heat transfer performance and phenomena of Al2O3-water nano-fluids from a plain surface in a pool. Int J Heat Mass Transfer 2005, 48: 2407–2419. 10.1016/j.ijheatmasstransfer.2004.12.047
Yu W, Choi SUS: The role of interfacial layers in the enhanced thermal conductivity of nanofluids, a renovated Maxwell model. J Nanoparticle Res 2003, 5: 167–171.
Yu W, Choi SUS: The role of interfacial layers in the enhanced thermal conductivity of nanofluids: a renovated Hamilton-Crosser model. J Nanoparticle Res 2004, 6: 355–361. 10.1007/s11051-004-2601-7
Abu-nada E: Application of nanofluids for heat transfer enhancement of separated flows encountered in a backward facing step. Int J Heat Fluid Flow 2008, 29: 242–249. 10.1016/j.ijheatfluidflow.2007.07.001
Abu-Nada E: Effects of variable viscosity and thermal conductivity of Al2O3- water nanofluid on heat transfer enhancement in natural convection. Int J Heat Fluid Flow 2009, 30: 679–690. 10.1016/j.ijheatfluidflow.2009.02.003
Akbari M, Behzadmehr A, Shahraki F: Fully developed mixed convection in horizontal and inclined tubes with uniform heat flux using nanofluid. Int J Heat Fluid Flow 2008, 29: 545–556. 10.1016/j.ijheatfluidflow.2007.11.006
Akbarinia A, Laur R: Investigating the diameter of solid particles effects on a laminar nanofluid flow in a curved tube using a two phase approach. Int J Heat Fluid Flow 2009, 30: 706–714. 10.1016/j.ijheatfluidflow.2009.03.002
Anoop KB, Sundararajan T, Das SK: Effect of particle size on the convective heat transfer in nanofluid in the developing region. Int J Heat Mass Transfer 2009, 52: 2189–2195. 10.1016/j.ijheatmasstransfer.2007.11.063
Avsec J: The combined analysis of phonon and electron heat transfer mechanism on thermal conductivity for nanofluids. Int J Heat Mass Transfer 2008, 51: 4589–4598. 10.1016/j.ijheatmasstransfer.2008.02.030
Bang IC, Heo G: An axiomatic design approach in development of nanofluid coolants. Appl Therm Eng 2009, 29: 75–90. 10.1016/j.applthermaleng.2008.02.004
Behzadmehr A, Saffar-avval M, Galanis N: Prediction of turbulent forced convection of a nanofluid in a tube with uniform heat flux using a two-phase approach. Int J Heat Fluid Flow 2007, 28: 211–219. 10.1016/j.ijheatfluidflow.2006.04.006
Bergman TL: Effect of reduced specific heats of nanofluids on single phase, laminar internal forced convection. Int J Heat Mass Transfer 2009, 52: 1240–1244. 10.1016/j.ijheatmasstransfer.2008.08.019
Bi S-S, Shi L, Zhang L-L: Application of nanoparticles in domestic refrigerators. Appl Therm Eng 2008, 28: 1834–1843. 10.1016/j.applthermaleng.2007.11.018
Bianco V, Chiacchio F, Manca O, Nardini S: Numerical investigation of nanofluids forced convection in circular tubes. Appl Therm Eng 2009, 29: 3632–3642. 10.1016/j.applthermaleng.2009.06.019
Chein R, Chuang J: Experimental microchannel heat sink performance studies using nanofluids. Int J Therm Sci 2007, 46: 57–66. 10.1016/j.ijthermalsci.2006.03.009
Chen G, Yu W, Singh D, Cookson D, Routbort J: Application of SAXS to the study of particle-size-dependent thermal conductivity in silica nanofluids. J Nanoparticle Res 2008, 10: 1109–1114. 10.1007/s11051-007-9347-y
Chen H, Ding Y, Lapkin A, Fan X: Rheological behaviour of ethylene glycol-titanate nanotube nanofluids. J Nanoparticle Res 2009, 11: 1513–1520. 10.1007/s11051-009-9599-9
Chon CH, Kihm KD, Lee SP, Choi SUS: Empirical correlation finding the role of temperature and particle size for nanofluid Al2O3thermal conductivity enhancement. Physics 2005., 87:
Chow L: High thermal conductivity, CTE matched nanocomposite. Presentation at AIAA Aerospace Sciences Meeting, University of Central Florida
Ben-Abdallah P, Domingues G, Moctar AOE: Enhanced thermal conductivity in nanofluids under the action of oscillating force fields. J Nanoparticle Res 2008, 10: 1115–1120. 10.1007/s11051-007-9346-z
Coblenz WS: Role of nanotechnology in thermal management. DARPA Disruptive Investment Strategies, Presentation at the AIAA Panel Session, January
Das SK, Narayan GP, Baby AK: Survey on nucleate pool boiling of nanofluids: the effect of particle size relative to roughness. J Nanoparticle Res 2008, 10: 1099–1108. 10.1007/s11051-007-9348-x
Wen DS, Ding YL: Experimental investigation into the pool boiling heat transfer of aqueous based ?-alumina nanofluids. J Nanoparticle Res 2005, 265–274.
Ding Y, Alias H, Wen D, Williams RA: Heat transfer of aqueous suspensions of carbon nanotubes (CNT nanofluids). Int J Heat Mass Transfer 2006, 49: 240–250. 10.1016/j.ijheatmasstransfer.2005.07.009
Hadjov KB: Influence of the particle size distribution on the thermal conductivity of nanofluids. J Nanoparticle Res 2009, 11: 1713–1718. 10.1007/s11051-008-9539-0
Duangthongsuk W, Wongwises S: Heat transfer enhancement and pressure drop characteristics of TiO2-water nanofluid in a double-tube counter flow heat exchanger. Int J Heat Mass Transfer 2009, 52: 2059–2067. 10.1016/j.ijheatmasstransfer.2008.10.023
Duangthongsuk W, Wongwises S: Measurement of temperature-dependent thermal conductivity and viscosity of TiO 2 -water nanofluids. Exp Therm Fluid Sci 2009, 33: 706–714. 10.1016/j.expthermflusci.2009.01.005
Eastman JA, Choi SUS, Li S, Yu W, Thompson LJ: Anomalously increased effective thermal conductivities of ethylene glycol-based nanofluids containing copper nanoparticles. Appl Phys Lett 2001, 78: 718–720. 10.1063/1.1341218
Elif: Natural convection of water-based nanofluids in an inclined enclosure with a heat source. Int J Therm Sci 2009, 48: 2063–2073. 10.1016/j.ijthermalsci.2009.03.014
Feng Y, Kleinstreuer C: Nanofluid convective heat transfer in a parallel-disk system. Int J Heat Mass Transfer 2010, 53: 4619–4628. 10.1016/j.ijheatmasstransfer.2010.06.031
Fu CJ, Zhang ZM: Nanoscale radiation heat transfer for silicon at different doping levels. Int J Heat Mass Transfer 2006, 49: 1703–1718. 10.1016/j.ijheatmasstransfer.2005.09.037
Godson L, Raja B, Lal DM, Wongwises S: Experimental investigation on the thermal conductivity and viscosity of silver-deionized water nanofluid. Exp Heat Transfer 2010, 23: 317–332. 10.1080/08916150903564796
Hadjov KB: Modified self-consisted scheme to predict the thermal conductivity of nanofluids. Int J Therm Sci 2009, 48: 2249–2254. 10.1016/j.ijthermalsci.2009.05.008
He Y, Men Y, Zhao Y, Lu H, Ding Y: Numerical investigation into the convective heat transfer of TiO2nanofluids flowing through a straight tube under the laminar flow conditions. Appl Therm Eng 2009, 29: 1965–1972. 10.1016/j.applthermaleng.2008.09.020
Heris SZ, Etemad SG, Esfahany MN: Experimental investigation of convective heat transfer of Al2O3/water nanofluid in circular tube. Int J Heat Fluid Flow 2007, 28: 203–210. 10.1016/j.ijheatfluidflow.2006.05.001
Hong T-k, Yang H-s: Study of the enhanced thermal conductivity of Fe nanofluids. Physics 2005, 97: 4–7.
Huang KD, Hua C: Heat transfer enhancement of nanofluids in rotary blade coupling of four-wheel-drive vehicles. Acta Mech 2005, 23: 11–23.
Hung YM: Analytical study on forced convection of nanofluids with viscous dissipation in microchannels. Heat Transfer Eng 2010, 31: 1184–1192. 10.1080/01457631003689344
Jain S, Patel HE, Das SK: Brownian dynamic simulation for the prediction of effective thermal conductivity of nanofluid. J Nanoparticle Res 2008, 11: 767–773.
Jou RY, Tzeng SC: Numerical research of nature convective heat transfer enhancement filled with nanofluids in rectangular enclosures. Int Commun Heat Mass Transfer 2006, 33: 727–736. 10.1016/j.icheatmasstransfer.2006.02.016
Jung J-y, Oh H-s, Kwak H-y: Forced convective heat transfer of nanofluids in microchannels. Int J Heat Mass Transfer 2009, 52: 466–472. 10.1016/j.ijheatmasstransfer.2008.03.033
Jung J-y, Yoo JY: Thermal conductivity enhancement of nanofluids in conjunction with electrical double layer (EDL). Int J Heat Mass Transfer 2009, 52: 525–528. 10.1016/j.ijheatmasstransfer.2008.07.016
Keblinski P, Prasher R, Eapen J: Thermal conductance of nanofluids: is the controversy over? J Nanoparticle Res 2008, 10: 1089–1097. 10.1007/s11051-007-9352-1
Kenneth EG: Diffusion, aggregation, and the thermal conductivity of nanofluids. Appl Phys Lett 2008, 93.
Khanafer K, Vafai K, Lightstone M: Buoyancy-driven heat transfer enhancement in a two-dimensional enclosure utilizing nanofluids. Int J Heat Mass Transfer 2003, 46: 3639–3653. 10.1016/S0017-9310(03)00156-X
Khandekar S, Joshi YM, Mehta B: Thermal performance of closed two-phase thermosyphon using nanofluids. Int J Therm Sci 2008, 47: 659–667. 10.1016/j.ijthermalsci.2007.06.005
Kim D, Hwang Y, Cheong SI, Lee JK, Hong D, Moon S, Lee JE, Kim SH: Production and characterization of carbon nano colloid via one-step electrochemical method. J Nanoparticle Res 2008, 10: 1121–1128. 10.1007/s11051-008-9359-2
Kim H, DeWitt G, McKrell T, Buongiorno J, Hu L-w: On the quenching of steel and zircaloy spheres in water-based nanofluids with alumina, silica and diamond nanoparticles. Int J Multiphase Flow 2009, 35: 427–438. 10.1016/j.ijmultiphaseflow.2009.02.004
Kim H, Kim J, Kim M: Experimental studies on CHF characteristics of nano-fluids at pool boiling. Int J Multiphase Flow 2007, 33: 691–706. 10.1016/j.ijmultiphaseflow.2007.02.007
Kim H, Kim J, Kim MH: Effect of nanoparticles on CHF enhancement in pool boiling of nano-fluids. Int J Heat Mass Transfer 2006, 42: 2003–2013.
Kim H, Kim M: Experimental study of the characteristics and mechanism of pool boiling CHF enhancement using nanofluids. Heat Mass Transfer 2007, 45: 991–998.
Kondaraju S, Jin EK, Lee JS: Direct numerical simulation of thermal conductivity of nanofluids: the effect of temperature two-way coupling and coagulation of particles. Int J Heat Mass Transfer 2010, 53: 862–869. 10.1016/j.ijheatmasstransfer.2009.11.038
Koo J, Kleinstreuer C: A new thermal conductivity model for nanofluids. J Nanoparticle Res 2005, 6: 577–588.
Kulkarni DP, Vajjha RS, Das DK, Oliva D: Application of aluminum oxide nanofluids in diesel electric generator as jacket water coolant. Appl Therm Eng 2008, 28: 1774–1781. 10.1016/j.applthermaleng.2007.11.017
Lee JS: Thermal conductivity measurement and sedimentation detection of aluminum oxide nanofluids by using the 3? method. Int J Heat Fluid Flow 2008, 29: 1456–1461. 10.1016/j.ijheatfluidflow.2008.04.007
Leong KC, Yang C: Investigations of thermal conductivity and viscosity of nanofluids. Int J Therm Sci 2008, 47: 560–568. 10.1016/j.ijthermalsci.2007.05.004
Leong KC, Yang C, Murshed SMS: A model for the thermal conductivity of nanofluids-the effect of interfacial layer. J Nanoparticle Res 2006, 8: 245–254. 10.1007/s11051-005-9018-9
Li J, Kleinstreuer C: Thermal performance of nanofluid flow in microchannels. Int J Heat Fluid Flow 2008, 29: 1221–1232. 10.1016/j.ijheatfluidflow.2008.01.005
Liao J, Zhang Y, Yu W, Xu L, Ge C, Liu J, Gu N: Linear aggregation of gold nanoparticles in ethanol. Colloids Surf A Physicochem Eng Aspects 2003, 223: 177–183. 10.1016/S0927-7757(03)00156-0
Liao L, Liu Z-h: Forced convective flow drag and heat transfer characteristics of carbon nanotube suspensions in a horizontal small tube. Int J Heat Mass Transfer 2009, 45: 1129–1136. 10.1007/s00231-009-0483-z
Lin Y-h, Chen H-l: Effect of silver nano-fluid on pulsating heat pipe thermal performance. Appl Therm Eng 2008, 28: 1312–1317. 10.1016/j.applthermaleng.2007.10.019
Liu Z, Xiong J, Bao R: Boiling heat transfer characteristics of nanofluids in a flat heat pipe evaporator with micro-grooved heating surface. Int J Multiphase Flow 2007, 33: 1284–1295. 10.1016/j.ijmultiphaseflow.2007.06.009
Lotfi H, Shafii MB: Boiling heat transfer on a high temperature silver sphere in nanofluid. Int J Therm Sci 2009, 48: 2215–2220. 10.1016/j.ijthermalsci.2009.04.009
Meibodi ME, Vafaei-Sefti M, Rashidi AM, Amrollahi A, Tabasi M, Kalal HS: Simple model for thermal conductivity of nanofluids using resistance model approach. Int Commun Heat Mass Transfer 2010, in press.
Milanova D, Kumar R: Role of ions in pool boiling heat transfer of pure and silica nanofluids. Appl Phys Lett 2005, 87: 185–194.
Minkowycz WJ: Nanofluids and critical heat flux, experimental and analytical study. Appl Therm Eng 2009, 29: 1281–1288. 10.1016/j.applthermaleng.2008.05.005
Mintsa HA, Roy G, Nguyen CT, Doucet D: New temperature dependent thermal conductivity data for water-based nanofluids. Int J Therm Sci 2009, 48: 363–371. 10.1016/j.ijthermalsci.2008.03.009
Mirmasoumi S, Behzadmehr A: Numerical study of laminar mixed convection of a nanofluid in a horizontal tube using two-phase mixture model. J Appl Therm Eng 2008, 28: 717–727. 10.1016/j.applthermaleng.2007.06.019
Mirmasoumi S, Behzadmehr A: Effect of nanoparticles mean diameter on mixed convection heat transfer of a nanofluid in a horizontal tube. Int J Heat Fluid Flow 2008, 29: 557–566. 10.1016/j.ijheatfluidflow.2007.11.007
Moghtaderi B: Comments on the effect of liquid layering on the thermal conductivity of nanofluids. J Nanoparticle Res 2008, 11: 1501–1507.
Mudawar I: Assessment of the effectiveness of nanofluids for single-phase and two-phase heat transfer in micro-channels. Int J Heat Mass Transfer 2007, 50: 452–463. 10.1016/j.ijheatmasstransfer.2006.08.001
Murshed SMS: Correction and comment on "thermal conductance of nanofluids: is the controversy over? J Nanoparticle Res 2009, 11: 511–512. 10.1007/s11051-008-9553-2
Murshed SMS, Leong KC, Yang C: Enhanced thermal conductivity of TiO2- water based nanofluids. Int J Therm Sci 2005, 44: 367–373. 10.1016/j.ijthermalsci.2004.12.005
Murshed SMS, Leong KC, Yang C: Investigations of thermal conductivity and viscosity of nanofluids. Int J Therm Sci 2008, 47: 560–568. 10.1016/j.ijthermalsci.2007.05.004
Namburu PK, Das DK, Tanguturi KM, Vajjha RS: Numerical study of turbulent flow and heat transfer characteristics of nanofluids considering variable properties. Int J Therm Sci 2009, 48: 290–302. 10.1016/j.ijthermalsci.2008.01.001
Nayak A, Gartia M, Vijayan P: An experimental investigation of single-phase natural circulation behavior in a rectangular loop with Al2O3nanofluids. Exp Therm Fluid Sci 2008, 33: 184–189. 10.1016/j.expthermflusci.2008.07.017
Nguyen C, Desgranges F, Roy G, Galanis N, Mare T, Boucher S, Anguemintsa H: Temperature and particle-size dependent viscosity data for water-based nanofluids - hysteresis phenomenon. Int J Heat Fluid Flow 2007, 28: 1492–1506. 10.1016/j.ijheatfluidflow.2007.02.004
Nguyen C, Galanis N, Polidori G, Fohanno S, Popa C, Lebechec A: An experimental study of a confined and submerged impinging jet heat transfer using Al2O3-water nanofluid. Int J Therm Sci 2009, 48: 401–411. 10.1016/j.ijthermalsci.2008.10.007
Nguyen CT, Desgranges F, Galanis N, Roy G, Maré T, Boucher S, Mintsa HA: Viscosity data for Al2O3-water nanofluid-hysteresis: is heat transfer enhancement using nanofluids reliable. Int J Therm Sci 2008, 47: 103–111. 10.1016/j.ijthermalsci.2007.01.033
Noie SH, Heris SZ, Kahani M, Nowee SM: Heat transfer enhancement using Al2O3/water nanofluid in a two-phase closed thermosyphon. Int J Heat Fluid Flow 2009, 30: 700–705. 10.1016/j.ijheatfluidflow.2009.03.001
Oztop H, Abunada E: Numerical study of natural convection in partially heated rectangular enclosures filled with nanofluids. Int J Heat Fluid Flow 2008, 29: 1326–1336. 10.1016/j.ijheatfluidflow.2008.04.009
Pantzali MN, Kanaris AG, Antoniadis KD, Mouza AA, Paras SV: Effect of nanofluids on the performance of a miniature plate heat exchanger with modulated surface. Int J Heat Fluid Flow 2009, 30: 691–699. 10.1016/j.ijheatfluidflow.2009.02.005
Pantzali MN, Mouza AA, Paras SV: Investigating the efficacy of nanofluids as coolants in plate heat exchangers (PHE). Chem Eng Sci 2009, 64: 3290–3300. 10.1016/j.ces.2009.04.004
Patel HE, Das SK, Sundararajan T, Nair AS, George B, Pradeep T: Thermal conductivities of naked and monolayer protected metal nanoparticle based nanofluids: manifestation of anomalous enhancement and chemical effects. Appl Phys Lett 2003, 83: 2931–2933. 10.1063/1.1602578
Peterson GP: Mixing effect on the enhancement of the effective thermal conductivity of nanoparticle suspensions (nanofluids). Int J Heat Mass Transfer 2007, 50: 4668–4677. 10.1016/j.ijheatmasstransfer.2007.03.015
Phelan PE: Brownian dynamics simulation to determine the effective thermal conductivity of nanofluid. J Appl Phys 2004, 95: 6492. 10.1063/1.1736319
Phuoc TX, Massoudi M: Experimental observations of the effects of shear rates and particle concentration on the viscosity of Fe2O3-deionized water nanofluids. Int J Therm Sci 2009, 48: 1294–1301. 10.1016/j.ijthermalsci.2008.11.015
Pil S, Choi SUS: Role of Brownian motion in the enhanced thermal conductivity of nanofluids. Appl Phys Lett 2004, 84: 4316–4318. 10.1063/1.1756684
Polidori G, Fohanno S, Nguyen CT: A note on heat transfer modelling of Newtonian nanofluids in laminar free convection. Heat Mass Transfer 2007, 46: 739–744.
Ponnappan PR: Thermophysics panel session 113-tp-8 introduction: impact of nanotechnology in thermal management. Presentation at the 44th AIAA Aerospace Sciences Meeting and Exhibit, Reno, NV 2006.
Prakashnarayan G, Anoop K, Sateesh G, Das S: Effect of surface orientation on pool boiling heat transfer of nanoparticle suspensions. Int J Multiphase Flow 2008, 34: 145–160. 10.1016/j.ijmultiphaseflow.2007.08.004
Quaresma J, Macedo E, Orlande H, Cotta R: An analysis of heat conduction models for nanofluids. Heat Transfer Eng 2010, 31: 1125–1136.
Rea U, McKrell T, Hu L-w, Buongiorno J: Laminar convective heat transfer and viscous pressure loss of alumina-water and zirconia-water nanofluids. Int J Heat Mass Transfer 2009, 52: 2042–2048. 10.1016/j.ijheatmasstransfer.2008.10.025
Santra AK, Chakraborty N, Sen S: Prediction of heat transfer due to presence of copper-water nanofluid using resilient-propagation neural network. Int J Therm Sci 2009, 48: 1311–1318. 10.1016/j.ijthermalsci.2008.11.009
Santra AK, Sen S, Chakraborty N: Study of heat transfer due to laminar flow of copper-water nanofluid through two isothermally heated parallel plates. Int J Therm Sci 2009, 48: 391–400. 10.1016/j.ijthermalsci.2008.10.004
Sefiane K, Bennacer R: Nanofluids droplets evaporation kinetics and wetting dynamics on rough heated substrates. Adv Colloid Interface Sci 2009, 147–148: 263–271.
Seon H, Kim H, Jo H, Kang S, Chang W, Hwan M: Experimental study of critical heat flux enhancement during forced convective flow boiling of nanofluid on a short heated surface. Int J Multiphase Flow 2010, 36: 375–384. 10.1016/j.ijmultiphaseflow.2010.01.004
Sergis A, Hardalupas Y: Anomalous heat transfer modes of nanofluids: a statistical analysis approach review. 9th HSTAM Congress on Mechanics, Limassol, Cyprus 2010, 12–14.
Sharma NN: Radiation model for nanoparticle: extension of classical Brownian motion concepts. J Nanoparticle Res 2007, 10: 333–340.
Sik K, Pil S, Choi SUS: Flow and convective heat transfer characteristics of water-based Al2O3nanofluids in fully developed laminar flow regime. Int J Heat Mass Transfer 2009, 52: 193–199. 10.1016/j.ijheatmasstransfer.2008.06.032
Singh PK, Anoop KB, Sundararajan T, Das SK: Entropy generation due to flow and heat transfer in nanofluids. Int J Heat Mass Transfer 2010, 53: 4757–4767. 10.1016/j.ijheatmasstransfer.2010.06.016
Soltani S, Etemad SG, Thibault J: Pool boiling heat transfer performance of Newtonian nanofluids. Heat Mass Transfer 2009, 45: 1555–1560. 10.1007/s00231-009-0530-9
Teja AS: The effect of particle size on the thermal conductivity of alumina nanofluid. J Nanoparticle Res 2009, 11: 1129–1136. 10.1007/s11051-008-9500-2
Tiwari R, Das M: Heat transfer augmentation in a two-sided lid-driven differentially heated square cavity utilizing nanofluids. Int J Heat Mass Transfer 2007, 50: 2002–2018. 10.1016/j.ijheatmasstransfer.2006.09.034
Tolmachev YV: Heat- and mass-transport in aqueous silica nanofluids. Int J Heat Mass Transfer 2009, 45: 1583–1588. 10.1007/s00231-009-0533-6
Trisaksri V, Wongwises S: Nucleate pool boiling heat transfer of TiO2-R141b nanofluids. Int J Heat Mass Transfer 2009, 52: 1582–1588. 10.1016/j.ijheatmasstransfer.2008.07.041
Vajjha RS, Das DK: Experimental determination of thermal conductivity of three nanofluids and development of new correlations. Int J Heat Mass Transfer 2009, 52: 4675–4682. 10.1016/j.ijheatmasstransfer.2009.06.027
Vajjha RS, Das DK, Kulkarni DP: Development of new correlations for convective heat transfer and friction factor in turbulent regime for nanofluids. Int J Heat Mass Transfer 2010, 53: 4607–4618. 10.1016/j.ijheatmasstransfer.2010.06.032
Vasiliev L, Hleb E, Shnip A, Lapotko D: Bubble generation in micro-volumes of "nanofluids". Int J Heat Mass Transfer 2009, 52: 1534–1539. 10.1016/j.ijheatmasstransfer.2008.08.009
Walsh PA, Egan VM, Walsh EJ: Novel micro-PIV study enables a greater understanding of nanoparticle suspension flows: nanofluids. Microfluidics Nanofluidics 2009, 8: 837–842.
Wang G-S, Bao R: Two-phase flow patterns of nitrogen and nanofluids in a vertically capillary tube. Int J Therm Sci 2009, 48: 2074–2079. 10.1016/j.ijthermalsci.2009.03.016
Wei X, Zhu H, Kong T, Wang L: Synthesis and thermal conductivity of Cu2O nanofluid. Int J Heat Mass Transfer 2009, 52: 4371–4374. 10.1016/j.ijheatmasstransfer.2009.03.073
Wen D: Mechanisms of thermal nanofluids on enhanced critical heat flux (CHF). Int J Heat Mass Transfer 2008, 51: 4958–4965. 10.1016/j.ijheatmasstransfer.2008.01.034
Wen D, Ding Y: Formulation of nanofluids for natural convective heat transfer applications. Int J Heat Fluid Flow 2005, 26: 855–864. 10.1016/j.ijheatfluidflow.2005.10.005
Wen D, Zhang L, He Y: Flow and migration of nanoparticle in a single channel. Heat Mass Transfer 2009, 45: 1061–1067. 10.1007/s00231-009-0479-8
Xie H, Lee H, Youn W, Choi M: Introduction I: Nanofluids containing multiwalled carbon nanotubes and their enhanced thermal conductivities. J Appl Phys 2003, 94: 4971.
Yang C: A combined model for the effective thermal conductivity of nanofluid. Appl Therm Eng 2009, 29: 2477–2483. 10.1016/j.applthermaleng.2008.12.018
Yao Z: Lattice Boltzmann model for nanofluid. Int J Heat Mass Transfer 2005, 41: 199–205.
You SM, Kim JH, Kim KH: Effect of nanoparticles on critical heat flux of water in pool boiling heat transfer. Appl Phys Lett 2003, 83: 3374–3376. 10.1063/1.1619206
Yu W, France DM, Smith DS, Singh D, Timofeeva EV, Routbort JL: Heat transfer to a silicon carbide/water nanofluid. Int J Heat Mass Transfer 2009, 52: 3606–3612. 10.1016/j.ijheatmasstransfer.2009.02.036
Zhang Z: Radiative properties of nanomaterials and radiative heat transfer at the nanoscale. Presentation at the 44th AIAA Aerospace Sciences Meeting and Exhibit, Georgia Institude of Technology, Atlanda, Georgia 2006.
Zhou L, Xuan Y, Li Q: Multiscale simulation of flow and heat transfer of nanofluid with lattice Boltzmann method. Int J Multiphase Flow 2010, 36: 364–374. 10.1016/j.ijmultiphaseflow.2010.01.005
Yang B, Han ZH: Thermal conductivity enhancement in water-in-FC72 nanoemulsion fluids. Appl Phys Lett 2006, 88: 261914–261914. 10.1063/1.2218325
Sul HY, Jung J-Y, Kang YT: Thermal conductivity enhancement of binary nanoemulsion (O/S) for absorption application. Int J Heat Mass Transfer 2011, 54: 1649–1653. 10.1016/j.ijheatmasstransfer.2010.11.016
Chiesa M, Garg J, Kang YT, Chen G: Thermal conductivity and viscosity of water-in-oil nanoemulsions. Colloids Surf A Physicochem Eng Aspects 2008, 326: 67–7. 10.1016/j.colsurfa.2008.05.028
Acknowledgements
The authors would like to thank EPSRC and Culham Centre for Fusion Energy (former UKAEA) for the award of CASE PhD studentship and associated financial support.
Author information
Authors and Affiliations
Corresponding author
Additional information
Competing interests
The authors declare that they have no competing interests.
Authors' contributions
AS conceived the study and performed the statistical analysis. YH participated in the design and coordination of the study. All authors read and approved the final manuscript.
Authors’ original submitted files for images
Below are the links to the authors’ original submitted files for images.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 2.0 International License (https://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
About this article
Cite this article
Sergis, A., Hardalupas, Y. Anomalous heat transfer modes of nanofluids: a review based on statistical analysis. Nanoscale Res Lett 6, 391 (2011). https://doi.org/10.1186/1556-276X-6-391
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/1556-276X-6-391