Abstract
Austenite grain size is an important influence factor for ductility of steel at high temperatures during continuous casting. Thermodynamic and kinetics calculations were performed to analyze the characteristics of Ti(C,N) precipitates formed during the continuous casting of micro-alloyed steel. Based on Andersen-Grong equation, a coupling model of second phase precipitation and austenite grain growth has been established, and the influence of second precipitates on austenite grain growth under different cooling rates is discussed. Calculations show that the final sizes of austenite grains are 2.155, 1.244, 0.965, 0.847 and 0.686 mm, respectively, under the cooling rate of 1, 3, 5, 7, and 10 °C·s-1, when ignoring the pinning effect of precipitation on austenite growth. Whereas, if taking the pinning effect into consideration, the grain growth remains stable from 1,350 °C, the calculated final sizes of austenite grains are 1.46, 1.02, 0.80, 0.67 and 0.57 mm, respectively. The sizes of final Ti(C,N) precipitates are 137, 79, 61, 51 and 43 nm, respectively, with the increase of cooling rate from 1 to 10 °C·s-1. Model validation shows that the austenite size under different cooling rates coincided with the calculation results. Finally, the corresponding measures to strengthen cooling intensity at elevated temperature are proposed to improve the ductility and transverse crack of slab.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Weng Yuqing. Ultrafine grained steel. Metallurgical Industry Press, 2003: 290–292. (In Chinese).
Gunabalapandian K, Samanta S, Ranjan R, et al. Investigation of austenitization in low carbon micro-alloyed steel during continuous heating. Metallurgical & Materials Transactions A, 2017, 48(5): 2099–2104.
Derda W, Wiedermann J. Some aspects of continuous casting of low carbon micro-alloyed steels with niobium and titanium. Archives of Metallurgy & Materials, 2012, 57(1): 303–310.
Li Y, Chen X, Liu K, et al. Reasonable temperature schedules for cold or hot charging of continuously cast steel slabs. Metallurgical and Materials Transactions A, 2013, 44(12): 5354–5364.
Dippenaar R, Bernhard C, Schider S, et al. Austenite grain growth and the surface quality of continuously cast steel. Metallurgical and Materials Transactions B, 2014, 45(2): 409–418.
Li Y, Wen G, Luo L, et al. Study of austenite grain size of Microalloyed steel by simulating initial solidification during continuous casting. Ironmaking & Steelmaking, 2015, 42(1): 41–48.
Dong D, Chen F, Cui Z. Modeling of austenite grain growth during austenitization in a low alloy steel. Journal of Materials Engineering and Performance, 2016, 25(1): 1–13.
Lee S J, Lee Y K. Prediction of austenite grain growth during austenitization of low alloy steels. Materials & Design, 2008, 29(9): 1840–1844.
Den Ouden D. Mathematical modelling of nucleating and growing precipitates: distributions and interfaces. Dissertation, Delft University of Technology, 2015.
Perrard F, Deschamps A, Maugis P. Modelling the precipitation of NbC on dislocations in α-Fe. Acta Materialia, 2007, 55(4): 1255–1266.
Xiao N, Tong M, Lan Y, et al. Coupled simulation of the influence of austenite deformation on the subsequent isothermal austenite–ferrite transformation. Acta Materialia, 2006, 54(5): 1265–1278.
Miettinen J, Louhenkilpi S, Holappa L. Coupled simulation of heat transfer and phase transformation in continuous casting of steel. ISIJ International, 1996, 36(Suppl): S183-S186.
Yasumoto K, Nagamichi T, Maehara Y, et al. Effects of alloying elements and cooling rate on austenite grain growth in solidification and the subsequent cooling processes of low alloy steels. Tetsu-to-Hagane, 1987, 73(14): 1738–1745.
Bernhard C, Reiter J, Presslinger H. A model for predicting the austenite grain size at the surface of continuously-cast slabs. Metallurgical and Materials Transactions B, 2008, 39(6): 885–895.
Wang Mingling, Yang Chunzheng, Tao Hongbiao. Formation mechanism of transverse corner crack on micro-alloyed steel slab. Iron and Steel, 2012, 47(10): 27–33 (In Chinese).
Lei Jialiu, Xue Zhengliang, Jiang Yuedong, et al. Effect of carbon content on TiN inclusion precipitation in tire cord steel. Journal of Materials and Metallurgy, 2014, 13(2): 125–127 (In Chinese).
Yong Qilong. Secondary Phases in Steels. Metallurgical Industry Press, 2006: 357–392 (In Chinese).
Andersen I, Grong O. Analytical modelling of grain growth in metals and alloys in the presence of growing and dissolving precipitates. Normal Grain Growth. Acta Metallurgica et Materialia, 1995, 43(7): 2673–2688.
Hu H, Rath B B. On the time exponent in isothermal grain growth. Metallurgical and Materials Transactions B, 1970, 1(11): 3181–3184.
Uhm S, Moon J, Lee C, et al. Prediction model for the austenite grain size in the coarse grained heat affected zone of Fe-C-Mn steels: Considering the Effect of Initial Grain Size on Isothermal Growth Behavior. ISIJ International, 2004, 44(7): 1230–1237.
Ma Fangjun. Precipitation behavior of the second phase and microstructural evolution of the surface layer of mirco-alloyed slabs in continuous casting. Dissertation, Chongqing University, 2010 (In Chinese).
Zener C. Theory of growth of spherical precipitates from solid solution. Journal of Applied Physics, 1949, 20(10): 950–953.
Stock J. NbC and TiN precipitation in continuously cast microalloyed steels. Dissertation, Colorado University, 2014.
Reiter J, Bernhard C, Presslinger H. Austenite grain size in the continuous casting process: Metallographic methods and evaluation. Materials Characterization, 2008, 59(6): 737–746.
Author information
Authors and Affiliations
Corresponding author
Additional information
*Yang Li Female, born in 1988, Ph.D. Associate Professor. Research interests: microstructure transformation and quality control in continuous casting.
This work was financially supported by the National Natural Science Foundation of China (No. 51504172) and (No. 51474163), and China Postdoctoral Science Foundation (No. 2015M572212).
Rights and permissions
About this article
Cite this article
Yang, L., Li, Y., Xue, Zl. et al. Influence of Ti(C,N) precipitates on austenite growth of micro-alloyed steel during continuous casting. China Foundry 14, 421–428 (2017). https://doi.org/10.1007/s41230-017-7098-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s41230-017-7098-7