Abstract
A356 aluminum casting alloys are used in fabrication of aircraft components where high strength is a requirement. The requirement of parts with light weight and high strength is constantly increasing. Aluminium matrix composites are considered to be new generation potential materials for many engineering applications. A356 alloy reinforced with Al2O3, SiC and Gr particulates with varied wt% was used to fabricate the hybrid composites by using squeeze casting method. The prepared composites were investigated for its structural and mechanical properties such as density, microstructural characterization, hardness, tensile strength, yield strength and elongation%. The composite density increased with increase in wt% of reinforcement. Microstructural examination revealed uniform distribution of reinforcement and XRD identified the presence of A356 matrix alloy and reinforcement Al2O3, SiC and Gr. A356/3wt%Al2O3/3wt%SiC/3wt%Gr exhibited superior hardness and tensile strength value of 119 BHN and 315 MPa. Gr reinforcement known for its soft characteristics compromised the addition of Al2O3 and SiC reinforcement towards the improved mechanical properties. The results obtained encouraged that A356 composite showed 40% improved hardness and 35%. The improved hardness and tensile strength than squeeze cast pure A356 aluminum alloy clearly shows it remains a clear substitute for aircraft components with high strength.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
Dwivedi SP, Sharma S, Mishra RK (2014) A356 aluminum alloy and applications- a review. Adv Mat Manuf Charac 4:81–86
Mahdavi S, Akhlaghi F (2011) Effect of the graphite content on the tribological behavior of Al/gr and Al/30SiC/gr composites processed by in situ powder metallurgy (IPM) method. Tribol Lett 44(1):1–12
Hassani A, Bagherpour E, Qods F (2014) Influence of pores on workability of porous Al/SiC composites fabricated through powder metallurgy + mechanical alloying. J Alloys Compd 591:132–142
Vedani M, D’Errico FD, Gariboldi E (2006) Mechanical and fracture behaviour of aluminium-based discontinuously reinforced composites at hot working temperatures. Compos Sci Technol 66(2):343–349
Nemati N, Khosroshahi R, Emamy M, Zolriasatein A (2011) Investigation of microstructure, hardness and wear properties of Al–4.5 wt.% cu–TiC nanocomposites produced by mechanical milling. Mater Des 32(7):3718–3729
Ruiz-Navas EM, Fogagnolo JB, Velasco F, Ruiz-Prieto JM, Froyen L (2006) One step production of aluminium matrix composite powders by mechanical alloying. Compos Part A: Appl Sci Manuf 37(11):2114–2120
Abdoli H, Salahi E, Farnoush H, Pourazrang K (2008) Evolutions during synthesis of Al–AlN-nanostructured composite powder by mechanical alloying. J Alloys Compd 461(1–2):166–172
Varol T, Canakci A, Ozsahin S (2013) Artificial neural network modeling to effect of reinforcement properties on the physical and mechanical properties of Al2024–B4C composites produced by powder metallurgy. Compos Part B: Eng 54:224–233
Fogagnolo JB, Velasco F, Robert MH, Torralba JM (2003) Effect of mechanical alloying on the morphology, microstructure and properties of aluminium matrix composite powders. Mater Sci Eng A 342(1–2):131–143
Cook BA, Peters JS, Harringa JL, Russell AM (2011) Enhanced wear resistance in AlMgB14–TiB2 composites. Wear 271(5–6):640–646
Kubota M, Kaneko J, Sugamata M (2008) Properties of mechanically milled and spark plasma sintered Al–AlB2 and Al–MgB2 nano-composite materials. Mater Sci Eng A 475(1–2):96–100
Sivasankaran S, Sivaprasad K, Narayanasamy R, Iyer VK (2010) Synthesis, structure and sinterability of 6061 AA100−x–x wt.% TiO2 composites prepared by high-energy ball milling. J Alloys Compd 491(1–2):712–721
Natrayan L, Senthilkumar M, Palanikumar K (2018) Optimization of squeeze cast process parameters on mechanical properties of Al2O3/SiC reinforced hybrid metal matrix composites using taguchi technique. Mater Res Exp 5(6):66516
Kok M, Ozdin K (2007) Wear resistance of aluminum alloy and its composites reinforced by Al2O3 particles. J Mater Proc Technol 183:301–309
Senthil Kumar M, Managalaraja RV, Senthil Kumar K, Natrayan L (2019) Processing and characterization of AA2024/Al2O3/SiC reinforced hybrid composites using squeeze casting technique. Iranian J Mater Sci Eng 16(2):55–67
Rajaram G, Kumar S, Rao TS, Kamaraj M (2010) Studies on high temperature wear and its mechanism of Al-Si/ graphite conditions under dry sliding conditions. Tribol Int 43(11):2152–2158
Saravanan RA, Surappa MK, Pramila Bai BN (1997) Erosion of A356 Al-SiCp composites due to multiple particle impact. Wear 202(2):154–164
Bains PS, Sidhu SS, Payal HS (2016) Fabrication and machining of metal matrix composites: a review. Mater Manuf Proc 31:553–573
Anand SS, Mohan B (2012) Enhanced hardness property in the development of Al-TiC composites through P/M techniques. Adv Mater Res 548:243–249
Sajjadi SA, Ezatpour HR, Beygi H (2011) Microstructure and mechanical properties of Al-Al2 O3 micro and nano composites fabricated by stir casting. Mater Sci Eng A 528(29–30):8765–8771
Zhong Y, Su G, Yang K (2024) Microsegregation and improved methods of squeeze casting 2024 aluminum alloy. J Mater Sci Technol 19:413–416
Murali S, Yong MS (2010) Liquid forging of thin Al-Si structures. J Mater Sci Technol 210:1276–1281
Ghomashchi MR, Vikhrov A (2000) Squeeze casting: an overview. J Mater Process Technol 101:1–9
Vijian P, Arunachalam VP (2005) Experimental study of squeeze casting of gunmetal. J Mater Process Technol 170:32–36
Brito CCD, Magalhaes FD, de Morais Costa AL, Siqueira CA (2010) Microstructural analysis and tensile properties of squeeze cast Al-7%mg alloy. Mater Sci Forum 643:119–123
Yue TM, Chadwick GA (1996) Squeeze casting of light alloys and their composites. J Mater Process Technol 58:302–307
Kim SW, Durrant G, Lee J-H, Cantor B (1998) The microstructure of direct squeeze cast and gravity die cast 7050 (Al-6.2Zn-2.3Cu-2.3Mg) wrought Al alloy. J Mater Synth Process 6:75–87
ASTM E10 - 01E1, Standard Test Method for Brinell Hardness of Metallic Materials
Alaneme KK, Ademilua BO, Bodunrin MO (2013) Mechanical properties and corrosion behaviour of Aluminium hybrid composites reinforced with silicon carbide and bamboo leaf ash. Tribol Ind 35:25–35
Tham LM, Gupta M, Cheng L (2001) Effect of limited matrix–reinforcement interfacial reaction on enhancing the mechanical properties of aluminium–silicon carbide composites. Acta Mater 49:3243–3253
Shorowordi K (2003) Microstructure and interface characteristics of B4C, SiC and Al2O3 reinforced Al matrix composites: a comparative study. J Mater Process Tech 142:738–743
Lai SW, Chung DDL (1996) Consumption of SiC whiskers by the Al–SiC reaction in aluminium-matrix SiC whisker composites. J Mater Chem 6:469–477
Thakur SK, Dhindaw BK (2001) The influence of interfacial characteristics between SiCp and mg/Al metal matrix on wear coefficient of friction and micro hardness. Wear 247:191–201
Suresha S, Sridhara BK (2010) Effect of addition of graphite particulates on the wear behavior in aluminium–silicon carbide–graphite composites. Mater Des 31:1804–1812
Natrayan L, Senthil Kumar M 2018 Study on squeeze casting of aluminum matrix composites- a review. Adv Manuf mater Sci. Springer, Cham 75-83
Manoj S (2009) Development of aluminium based silicon carbide particulate metal matrix composite. J Miner Mater Charac Eng 8:455–467
Thakur SK, Dhindaw BK (2001) Influence of interfacial characteristics between SiCp and mg/Al metal matrix on wear, coefficient of friction and microhardenss. Wear 247:199–201
Suresha S, Sridhara BK (2010) Effect of addition of graphite particulates on the wear behaviour in aluminium–silicon carbide–graphite composites. Mater Des 31:1804–1812
Sahin Y (2003) Preparation and some properties of SiC particle reinforced aluminium alloy composites. Mater Des 24:671–679
Myriounis DP (2009) Effects of heat treatment on microstructure and the fracture toughness of SiCp/Al alloy metal matrix composites. J Adv Mater 41:18–27
Umanath K, Palanikumar K, Selvamani ST (2013) Analysis of dry sliding wear behaviour of Al6061/SiC/Al2O3 hybrid metal matrix composites. Compos Part B-Eng 53:159–168
Yigezu BS, Mahapatra MM, Jha PK (2013) Infuence of reinforcement type on microstructure, hardness, and tensile properties of an aluminum alloy metal matrix composite. J Miner Mater Charac Eng 1:124–130
Tian J, Shobu K (2004) Fracture strength of melt-infiltrated SiC-mullite composite. J Mater Sci 39:3751–3755
Lin JT, Bhattacharyya D, Lane C (1995) Machinability of a silicon carbide reinforced aluminium metal matrix composite. Wear 181:883–888
Rao BT (2018) An experimental investigation on mechanical and wear properties of Al7075/SiCp composites: effect of SiC content and particle size. J Tribol 140(3):031601
Acknowledgements
The authors thank the Management of VIT University and the Dean- School of Mechanical Engineering, VIT Chennai, India and School of Electrical and Communication Sciences, B S Abdur Rahman Crescent Institute of Science and Technology, Chennai, India for their support and encouragement to publish this work. This research did not receive any specific grant from funding agencies in the public, commercial, or not-for-profit sectors.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Senthil Kumar, M., Vanmathi, M. & Sakthivel, G. SiC Reinforcement in the Synthesis and Characterization of A356/AL2O3/Sic/Gr Reinforced Composite- Paving a Way for the Next Generation of Aircraft Applications. Silicon 13, 2737–2744 (2021). https://doi.org/10.1007/s12633-020-00625-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12633-020-00625-9