Abstract
The anodic dissolution process of a crack tip at 2024-T351 aluminium alloy (AA2024-T351) was determined by means of scanning Kelvin probe (SKP). Wedge-open loading (WOL) specimens were immersed in a 3.5wt% NaCl solution. After various durations of immersion, the Volta potential distributions around the crack were measured by SKP and the surface morphologies were observed by scanning electron microscopy (SEM). It is found that there is a nonuniform distribution of Volta potential around the crack. Before immersion, the Volta potential at crack tip is more negative than that in other regions. However, after immersion, a converse result occurs with the most positive Volta potential measured at the crack tip. SEM observations demonstrate that the noticeable positive shift of Volta potential results from the formation of corrosion products which deposit around the crack tip. Energy-dispersive spectrometry (EDS) analysis shows that the corrosion products are mainly Al oxide and Cu-rich particles. These observations implicate that the applied stress contributes to the preferential anodic dissolution of the crack tip and the redistribution of Cu.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
E.A. Starke Jr. and J.T. Staley, Application of modern aluminum alloys to aircraft, Prog. Aerosp. Sci., 32(1996), No.2–3, p.131.
C.F. Dong, H. Sheng, Y.H. An, X.G. Li, and K. Xiao, Local electrochemical behavior of 2A12 aluminium alloy in the initial stage of atmospheric corrosion under Cl− conditions, J. Univ. Sci. Technol. Beijing, 31(2009), No.7, p.878.
B.J. Connolly and J.R. Scully, Corrosion cracking susceptibility in Al-Li-Cu alloys 2090 and 2096 as a function of isothermal aging time, Scripta Mater., 42(2000), No.11, p.1039.
X. Liu, G.S. Frankel, B. Zoofan, and S.I. Rokhlin, In-situ observation of intergranular stress corrosion cracking in AA2024-T3 under constant load conditions, Corros. Sci., 49(2007), No.1, p.139.
K. Jones, S.R. Shinde, P.N. Clark, and D.W. Hoeppner, Effect of prior corrosion on short crack behavior in 2024-T3 aluminum alloy, Corros. Sci., 50(2008), No.9, p.2588.
M. Dixit, R.S. Mishra, and K.K. Sankaran, Structure-property correlations in Al 7050 and Al 7055 high-strength aluminum alloys, Mater. Sci. Eng., A, 478(2008), No.1–2, p.163.
N. Birbilis, M.K. Cavanaugh, L. Kovarik, and R.G. Buchheit, Nano-scale dissolution phenomena in Al-Cu-Mg alloys, Electrochem. Commun., 10(2008), No.1, p.32.
R.G. Song, W. Dietzel, B.J. Zhang, W.J. Liu, M.K. Tseng, and A. Atrens, Stress corrosion cracking and hydrogen embrittlement of an Al-Zn-Mg-Cu alloy, Acta Mater., 52(2004), No.16, p.4727.
J. Hahm and S.J. Sibener, Stress-modified electrochemical reactivity of metallic surfaces: Atomic force microscopy imaging studies of nickel and alloyed aluminum, Appl. Surf. Sci., 161(2000), No.3, p.375.
Al.Th. Kermanidis, D.G. Stamatelos, G.N. Labeas, and Sp.G. Pantelakis, Tensile behaviour of corroded and hydrogen embrittled 2024 T351 aluminum alloy specimen, Theor. Appl. Fract. Mech., 45(2006), No.2, p.148.
T. Magnin, A. Chambreuil, and B. Bayle, The corrosion-enhanced plasticity model for stress corrosion cracking in ductile fcc alloys, Acta Mater., 44(1996), No.4, p.1457.
D. Najjar, T. Magnin, and T.J. Warner, Influence of critical surface defects and localized competition between anodic dissolution and hydrogen effects during stress corrosion cracking of a 7050 aluminium alloy, Mater. Sci. Eng., A, 238(1997), No.2, p.293.
K.R. Cooper and R.G. Kelly, Crack tip chemistry and electrochemistry of environmental cracks in AA 7050, Corros. Sci., 49(2007), No.6, p.2636.
T. Shoji, Z. Lu, and H. Murakami, Formulating stress corrosion cracking growth rates by combination of crack tip mechanics and crack tip oxidation kinetics, Corros. Sci., 52(2010), No.3, p.769.
L. Lacroix, L. Ressier, C. Blanc, and G. Mankowski, Statistical study of the corrosion behavior of Al2CuMg intermetallics in AA2024-T351 by SKPFM, J. Electrochem. Soc., 155(2008), No.1, p.C8.
X. Tang and Y.F. Cheng, Micro-electrochemical characterization of the effect of applied stress on local anodic dissolution behavior of pipeline steel under near-neutral pH condition, Electrochim. Acta, 54(2009), No.5, p.1499.
P. Bergveld, J. Hendrikse, and W. Olthuis, Theory and application of the material work function for chemical on the field principle, Meas. Sci. Technol., 9(1998), No.11, p.1801.
C.F. Dong, H. Sheng, Y.H. An, X.G. Li, K. Xiao, and Y.F. Cheng, Corrosion of 7A04 aluminum alloy under defected epoxy coating studied by localized electrochemical impedance spectroscopy, Prog. Org. Coat., 67(2010), No.3, p.269.
T. Suter and R.C. Alkire, Microelectrochemical studies of pit initiation at single inclusions in Al 2024-T3, J. Electrochem. Soc., 148(2001), No.1, p.B36.
J.G. Speight, Lange’s Handbook of Chemistry, 15th ed., McGraw-Hill Book Company, New York, 2005, p.1.132.
R.G. Buchheit, L.P. Montes, M.A. Martinez, J. Michael, and P.F. Hlava, The electrochemical characteristics of bulk-synthesized Al2CuMg, J. Electrochem. Soc., 146(1999), No.12, p.4424.
Author information
Authors and Affiliations
Corresponding author
Additional information
This work was financially supported by the Fundamental Research Funds for the Central Universities (No.FRF-BR-10-037B) and the National Natural Science Foundation of China No.51131005]
Rights and permissions
About this article
Cite this article
Sheng, H., Dong, Cf., Xiao, K. et al. Anodic dissolution of a crack tip at AA2024-T351 in 3.5wt% NaCl solution. Int J Miner Metall Mater 19, 939–944 (2012). https://doi.org/10.1007/s12613-012-0651-x
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12613-012-0651-x