Abstract
The circulation period of RH vacuum refining was studied to promote the refining efficiency. The influences of the lift gas flow rate and submersion depth of snorkels on the circulation period, and the relationship between mixing time and circulation flow were discussed. The effects of the lift gas flow rate and submersion depth on the degassing rate in one circulation period were studied by water modeling. The results show that the circulation period is shortened by increasing the lift gas flow rate. The circulation period is the shortest when the submersion depth of snorkels is 560 mm. The whole ladle can be mixed thoroughly after three times of circulation. Increasing the lift gas flow rate can enhance the degassing rate of RH circulation.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
F. Ahrenhold and W. Pluschkell, Circulation rate of liquid steel in RH degassers, Steel Res., 69(1998), p.54.
H.F. Shu, C. Song, X.F. Zhang, et al., Study on circulation flow rate in water model of RH-MFB vacuum refining process, J. Mater. Metall. (in Chinese), 2(2004), p.107.
X.Y. Jiang, J.H. Wei, L.J. Wen, et al., Flow and mixing characteristics of molten steel in a 150 t RH degasser and influence of gas injection port diameter, Shanghai Met. (in Chinese), 29(2007), p.34.
C. Kamata, H. Matrumura, H. Miyasaka, et al., Cold model experiments on the circulation flow in RH reactor using a laser Doppler velocimeter, Steelmaking Conf. Proc., 81(1998), p.606.
T.Q. Li, Y.P. Bao, J.H. Liu, et al., Study on different RH processes to produce pipeline steel-X70, J. Univ. Sci. Technol. Beijing (in Chinese), 2007, S1, p.32.
C.H. Huang and X. Yu, Studies on homogenization of compositions and temperature of liquid steel in RH refining, Steelmaking (in Chinese), 21(2005), p.22.
Y. Qu and J. Liu, Introduction to Metallurgical Reaction Engineering (in Chinese), Metallurgical Industry Press, Beijing, 1988, p.70.
H.T. Hu, J.H. Wei, H.F. Huang, et al., Effects of gas port inner diameter on molten steel flow and mixing characteristics during RH refining process, Spec. Steel (in Chinese), 25(2004), p.9.
F. Ahrenhold and W. Pluschkell, Mixing phenomena inside the ladle during RH decarburization of steel melts, Steel Res., 70(1999), p.314.
F.S. Qi, B.K. Li, and H.G. Chen, Investigation on mixing behavior of RH vacuum degassing vessel, Chin. J. Process Eng. (in Chinese), 8(2008), p.31.
Y.L. Jin, Y.P. Bao, F. Yue, et al., Water model study on mixing time in a 210 t ladle in the CAS process, Steelmaking (in Chinese), 23(2007), p.36.
R.K. Hanna, T. Jones, R.I. Blake, and M.S. Millman, Water modelling to aid improvement of degasser performance for production of ultralow carbon interstitial free steels, Ironmaking Steelmaking, 21(1994), p.37.
X.G. Xiao and Y.G. Xie, Foundation of Metallurgical Reaction Engineering (in Chinese), Metallurgical Industry Press, Beijing, 1997, p.36.
D.Q. Geng, H. Lei, J.C. He, Fluid flow in RH reactor under different parameters of immersion tubes, Iron Steel (in Chinese), 43(2008), p.35.
T. Lehner, Homogenization desulfurization and deoxidation of liquid steel by powder injection, [in] McMaster Symposium on Iron and Steelmaking, Hamilton, USA, 1979, p.1.
Author information
Authors and Affiliations
Corresponding author
Additional information
This work was financially supported by the National Key Technology R & D Program of China (No.2006BAE03A06).
Rights and permissions
About this article
Cite this article
Ai, Xg., Bao, Yp., Jiang, W. et al. Periodic flow characteristics during RH vacuum circulation refining. Int J Miner Metall Mater 17, 17–21 (2010). https://doi.org/10.1007/s12613-010-0103-4
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12613-010-0103-4