Abstract
Characteristics of the deposited layer in a powder bed fusion (PBF) system depend on the formation of the fed-powder layer. The objective of this paper is to investigate the influence of feeding parameters of the powder on the formation of the fed-powder layer in a PBF system. The effects of the gap between the feeding blade and the base plate, the volume of the powder and the supplied shape of the powder on the formation of the fed-powder layer and the defect mode of the powder bed were investigated via manual powder feeding experiments. From the results of the manual experiments, appropriate feeding conditions for achieving the desired formation of the fed-powder layer were estimated. The influence of the speed of the feeding blade and the supplied shape of powders on the formation of the fed-powder layer was examined through automatic powder feeding experiments. From the results of the automatic experiments, a practical speed of the feeding blade and an appropriate supplied shape of powders were determined.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Abbreviations
- φ:
-
gap between feeding blade and base plate
- Ω:
-
volume of the powder
- Δ:
-
supplied shape of the powder
- ω:
-
maximum width of the fed-powder layer
- ψ:
-
width of the fed-powder layer in the centerline of the building platform
- ζ:
-
maximum length of the fed-powder layer on the building platform
- η:
-
filling ratio on the building platform
- λf :
-
filled area by powders on the building platform
- λt :
-
total area of the building platform
- φc,w :
-
critical gap from the viewpoint of the width of the fed-powder layer in the centerline of the building platform
- φc,l :
-
critical gap from the viewpoint of the maximum length of the fed-powder layer on the building platform
- φw :
-
minimum gap without any defect
- κ:
-
normalized volume ratio
- t:
-
deposition thickness of the powder
- d:
-
diameter of the building platform
- V:
-
speed of feeding blade
- Dp.max :
-
Maximum diameter of the powder
References
Bikas, H., Stavropoulos, P., and Chryssolouris, G., “Additive Manufacturing Methods and Modelling Approaches: A Critical Review,” International Journal of Advanced Manufacturing Technology, Vol. 83, Nos. 1-4, pp. 389–405, 2016.
Ko, H., Moon, S. K., and Hwang, J., “Design for Additive Manufacturing in Customized Products,” Int. J. Precis. Eng. Manuf., Vol. 16, No. 11, pp. 2369–2375, 2015.
Matsumoto, M., Yang, S., Martinsen, K., and Kainuma, Y., “Trends and Research Challenges in Remanufacturing,” Int. J. Precis. Eng. Manuf.-Green Tech., Vol. 3, No. 1, pp. 129–142, 2016.
Kang, H. S., Lee, J. Y., Choi, S. S., Kim, H., Park, J. H., et al., “Smart Manufacturing: Past Research, Present Findings, and Future Directions,” Int. J. Precis. Eng. Manuf.-Green Tech., Vol. 3, No. 1, pp. 111–128, 2016.
Ho, C. M. B., Ng, S. H., and Yoon, Y.-J., “A Review on 3D Printed Bioimplants,” Int. J. Precis. Eng. Manuf., Vol. 16, No. 5, pp. 1035–1046, 2015.
Gao, W., Zhang, Y., Ramanujan, D., Ramani, K., Chen, Y., et al., “The Status, Challenges, and Future of Additive Manufacturing in Engineering,” Computer-Aided Design, Vol. 69, pp. 65–89, 2015.
Ahn, D.-G., “Direct Metal Additive Manufacturing Processes and their Sustainable Applications for Green Technology: A Review,” Int. J. Precis. Eng. Manuf.-Green Tech., Vol. 3, No. 4, pp. 381–395, 2016.
Cheah, C., Chua, C., Lee, C., Feng, C., and Totong, K., “Rapid Prototyping and Tooling Techniques: A Review of Applications for Rapid Investment Casting,” International Journal of Advanced Manufacturing Technology, Vol. 25, Nos. 3-4, pp. 308–320, 2005.
Frazier, W.E., “Metal Additive Manufacturing: A Review,” Journal of Materials Engineering and Performance, Vol. 23, No. 6, pp. 1917–1928, 2014.
Wohlers, T. T. and Caffrey, T., “Wohlers Report 2015: 3D Printing and Additive Manufacturing State of the Industry Annual Worldwide Progress Report,” Wohlers Associates, 2015.
Beaman, J. J. and Deckard, C. R., “Selective Laser Sintering with Assisted Powder Handling,” US Patent, 4938816A, 1990.
Deckard, C. R., Beaman, J. J., and Darrah, J. F., “Selective Laser Sintering with Layerwise Cross-Scanning,” WO Patent, 1992008567 A1, 1992.
Colin, C., Bartout, J.-D., Shaker, E., Marchat, D., and Nimal, D., “Selective Laser Melting Process,” US Patent, 20160052162A1, 2016.
Küsters, Y., Lupp, F., Rehme, O., and Schäfer, M., “Process for Selective Laser Melting and System for Carrying Out Said Process,” US Patent, 20140131921A1, 2014.
SLM-SOLUTIONS, “Selective Laser Melting Machine SLM 500,” https://slm-solutions.com/products/machines/selective-laser-meltingmachine-slm-500 (Accessed 10 MAR 2017)
CONCEPTLASER, “M2” https://newsroom.concept-laser.de/ videos.html (Accessed 10 MAR 2017)
Agile-Manufacturing Inc., “SINTERSTATION® HIQTM SERIES SLS® SYSTEMS” http://www.agile-manufacturing.com/files/ products/sinterstation-hiq.pdf (Accessed 10 MAR 2017)
3D SYSTEMS, “ProX SLS 500,” https://www.3dsystems.com/3dprinters/ prox-sls-500 (Accessed 7 MAR 2017)
3D SYSTEMS, “ProX DMP 300,” https://www.3dsystems.com/3dprinters/ prox-dmp-300 (Accessed 7 MAR 2017)
e-Manufacturing Solutions, “EOSINT M 280,” https://www.eos.info/systems_solutions/metal/systems_equipment/eosint_m280 (Accessed 7 MAR 2017)
Arcam AB, “Arcam Q20plus–for Production of Aerospace Components,” http://www.arcam.com/technology/products/arcamq20/ (Accessed 7 MAR 2017)
Spears, T. G. and Gold, S. A., “In-Process Sensing in Selective Laser Melting (SLM) Additive Manufacturing,” Integrating Materials and Manufacturing Innovation, Vol. 5, No. 1,Article No. 2, 2016. (DOI: 10.1186/s40192-016-0045-4)
Van der Schueren, B. and Kruth, J.-P., “Powder Deposition in Selective Metal Powder Sintering,” Rapid Prototyping Journal, Vol. 1, No. 3, pp. 23–31, 1995.
Kurzynowski, T., Chlebus, E., Kuźnicka, B., and Reiner, J., “Parameters in Selective Laser Melting for Processing Metallic Powders,” Proc. of SPIE, Vol. 8239, Paper No. 823914, 2012. (DOI: 10.1117/12.907292)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Lee, HJ., Song, JG. & Ahn, DG. Investigation into the influence of feeding parameters on the formation of the fed-powder layer in a powder bed fusion (PBF) system. Int. J. Precis. Eng. Manuf. 18, 613–621 (2017). https://doi.org/10.1007/s12541-017-0073-9
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-017-0073-9